Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11060094991 > Instructions

11060094991 Kenmore Dryer - Instructions

All installation instructions for 11060094991 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11060094991
376-390 of 563
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My dryer had stop working and the terminal block, wires, and dryer plug burnt out

  • Customer: tiffanee from antioch, TN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I replace the terminal block, wires , and dryer plug I unscrewed the back of the dryer and basically replace was burnt out. I was about to pay 200.00 to have it done but I looked on youtube and seen how easy it was so I just chose the site to order what I needed to be replace and it arrived quickly and more affordable to do it myself. Thanks I hope the was useful.

door would not close

  • Customer: Daniel from Stratford, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Slipped screwdriver on top and bottom of catch and pullef out. Pressed new catch in plact. Job finished.

dryer doesn't complete it's cycle

  • Customer: MICHAEL from PHOENIX, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removal of the back panel was easy - 9 screws - replaced both the thermistor and the two-terminal thermal fuse - put back panel on - supplied power - tested it - works like a champ.

Felt wears on the dryer lint screen

  • Customer: Judy from Cloverdale, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
No repair. Just replaced the screens in the dryer and they slide in and out to clean. The felt gets worn fast.

Washer quit running when lid was closed

  • Customer: Colleen from Indianapolis, IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.

dryer would not turn on

  • Customer: Eric from Wallkill, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
found door switch was ng, replaced however the new part would not fit like the original. I had to use part of the old switch to make it work. It seems as if there was a piece missing from the new replacement part. There was no way it could have worked they way it was recieved. The door switch needs some sort of stand off spacer in order to match the original part. Lucky for me I saved the old part.

lint filter coming apart

  • Customer: Alan from Oklahoma City, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed old one, threw it away, and inserted new one.

Dryer stopped heating

  • Customer: Daniel from Palmyra, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Using information found on this site, I was able to quickly locate the two bolts on the lower front panel of the dryer to get at the heating element. Once I removed the panel, I was able to use a multi-meter to determine that the heating element was the issue as the resistance reading was infinite opposed to the expected 10 ohms. When the replacement part arrived, I then re-accessed the heating element to remove it. I removed two bolts from the front deflector to gain access to the heating element (after opening the lower panel) and also removed a third bolt that held the heating element in. Once those were removed, I was able to remove the old heating element which was indeed bad as the wire was broken. I did find that it took a little effort to remove the old heating element. It was quite firmly placed in its location however once I put enough effort into it, it came out quite nicely and the replacement element went in quickly.

Broken door catch

  • Customer: Chuck from Bozeman, MT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed two small screws on door edge, pop out broken part, insert new part, replace screws. Took 2 minutes 18 seconds. Nice to have various door catches in the Kit. This was a repair on a 1979 Whirlpool Dryer. Great price & service!!

Dryer was not heating up

  • Customer: Lynn from Spencer, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I watched a fix it video and than just followed what it said to do. My husband was very impressed and it saved us a lot of money. I had my dryer running in no time. Parts came very quickly after I ordered them. Thank you

old idler pulley was worn out

  • Customer: David J from Eagar, AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Simply slid new idler wheel on then popped thr tri ring on. The belt replacment was the hardest thing which was also easy. I think pulling the dryer away from the wall was the most difficult thing.

Needed to vent to side due to space requirements

  • Customer: Harlon from Browns Summit, NC
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Upon receipt of the new vent kit, I removed the dryer from its location and took it in to the garage. This facilitated a roomier work space. The directions were easy to follow and the work to be performed was very easy in this setting.

The Drier started making an unusual noise, then stoped in the middle of the cycle. I attempted to start it again after a while and it did start to stop again after a few minutes.

  • Customer: Armando from Sterterling Heights, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
This appliance is 14 years old. I debated whether or not if worth to be repaired. I decided to repair it since a new one of comparable model is about $600. Firts, Disconnect the appliance. Remove the control panel side covers and unscrew the screws in the bottom, (one on each side) Flip the control panel up. Now you have access to the 3 screws that hold the drier top on place. Remove the 3 screws and slide the panel towards you and lift standing on the front of the appliance. Set the top aside. The fron bottom panel is attached with two clips on top and hinges on two bottom clips. With a potty knife or flat screw press in each top clips and pulls the cover towards you and lift that will removed the cover. Next, un screw the two screws in the bottom of the top front panel. Disconect the wires of the close door switch. I usially take a picture of the connections before discconnecting anything so I can use as reference when putting it all together again. Remove the two top screws. Remove the spring of the door (two, one on each side), remove the lint trap. Be careful if you open the door after you remove the springs and make sure whne you close the door is snaped in the close position. Remove the front top panel. Next, remove the blower cover (two screws on the front of it, Remove the blower ring ( two screws) Remove the belt by pushing down the spring loaded pulley and sliding the belp to the side. Grabing the tub by the belt carfully lift it and slide it out from the drier enclosure. Using a 1/2 in socket wrench place it in the center of the blower and hold the motor shaft at the other end by the pulley using adjustable wrench. Unscrew and remove the blower. Remove the back cover of the blower (4 screws) Discconnect the motor harness and unclip the two clips holding the motor to the mount bracket. Remove the motor and replace with the new one. Follow these instructions in revers order. It was very easy and my drier is working great now. I inspected the belt and pulleys and lubricared all moving components and of course cleaned and vacum all debry and lint. I hope these instructions help you and good luck :)

Dryer door would not close and latch on both catches w/o pushing them shut individually.

  • Customer: David from Middleton, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Our make/model was not on the online instruction, but it was similar. Ours had a glass (plastic)front window in the door. To remove the top catch you had to take out the top four screws that hold the door together (philips head screws) allowing you to pull back the gray plastic strip to access the top latch, then replace it like in the online directions using a needle nose pliers. The bottom catch, once the two remaining the screws were out gives you access to the bottom catch. Remove it with the pliers and snap the new ones into place. You can completely take out the window when you replace the bottom latch if you want.

door wasn't shutting

  • Customer: Tom from Crystal Lake, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Just pulled the old parts out on door latch and put the new ones in. Thanks Parts Select for your prompt response and easy process for order and shipment.
All Instructions for the 11060094991
376-390 of 563