Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11047512602 > Instructions

11047512602 Kenmore Washer - Instructions

All installation instructions for 11047512602 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11047512602
46-60 of 141
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

pump impeller broken

  • Customer: Steve from OHATCHEE, AL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 1 people found this instruction helpful
Only needed a pair of pliers for the clamps on the hoses connected to the pump. Removed the old pump ( no tools needed) and reinstalled the hoses. Works like a charm!

F21 Error - Water in washer not draining.

  • Customer: Christopher from GLENDALE, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
This repair is something even the most casual DIY'er could accomplish. What made this even easier for me was the fact that my washer was on a pedestal so accessing the 1/4" screws were extremely easy. There is no need to tilt or lift the washer. Just open the drawer and all three screws are visible. It also made draining the water out of the washer very convenient. The video perfectly describes how to accomplish the repair and allowed me to diagnose the problem by taking off the panel, opening the trap door and allowing the water to drain into a small trashcan until all the water is removed. I could physically see that the impeller was detached from the motor and found the culprit that caused the problem - a small vile of eye drops... From there, ordered the pump, two days later, replaced it with the new and I swear the new pump must be stronger than the original because towels come out near dry after a spin cycle. Very satisfying repair!

The washer drain pump had to be replaced.

  • Customer: John from ARMINGTON, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Unplugged the washer from electric outlet. Removed front cover by using nut driver to remove the two screws. Drained the water from the washer into a pan by loosening the cap on the filter. Removed the two hoses by compressing clamps with pliers. Unplugged the electric wire from old pump. Used screw driver to pry rubber feet of old pump loose from washer floor panel. Set old pump aside. Installed new pump using a little dish soap to help attach rubber feet to washer. Attached the two hoses using pliers. Plugged electric wire into new unit. Ran washer to check for leaks. Replaced front cover using nut driver on the two screws.

replace the pump motor

  • Customer: Jay from MALVERN, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
First tilt the washer back so you can drain water from the lines to the pump and the pump itself. Disconnect the lines with a pair of pliers and use a screwdriver to move the rubber stopper so that the pump will move to the right. With pump now in position to lift up and out of the washer , do it so you can disconnect the wire assembly. Replace the pump starting with the wires, then slide it in place and secure it with the rubber stopper. Attach the lines and make sure they are well sitted and clamped. set on feet and you are ready to wash.

Leaking bellow on my front loader..

  • Customer: Frederick W from FLETCHER, OK
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
Followed the most helpful video.with some system differences. Had quite a bit of fitment challenge with the inner bellow sealing process...finally used dish soap to help 'stretch' the thing on.Works fine now thanks.

Bought a washer without front leveling feet

  • Customer: Rick from Lennon, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 2 people found this instruction helpful
The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

Washer posting a f6 error

  • Customer: Robert from Salt Lick, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 29 of 91 people found this instruction helpful
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

The bottom conter balance broke in half.

  • Customer: Judith M from Apple Valley, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Had my appliance man do it. It was the first one he had ever done in 20 years of working on Whirlpool. It was quick. The parts I received from you were cheaper than his supplier. Needless to say that made me very happy!

leaking water from door

  • Customer: Darrell from Ponca City, OK
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
After getting dress that wife denies closing in door out the repair wasant to hard. There are 3 or 4 phillips screws in back that holds top on that have to be taken out and the kick plate cover on bottom just snaps off but the rest is covered very well by other discriptions.(by the way the dress had to be thrown away so not only did i get to by bellow but a new dress also and the bellow was cheaper)

Timer was not advanced due to door lock failure

  • Customer: EMMANUEL from CLINTON, MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Searched internet for diagnosis. Ran diagnostic test using the diagnostic manual from whirlpool. The error code was F29. Replaced door latch but problem was not solved. Then order the Motor Control Unit. Removed old control unit through the top by removing the top washer cover and numbering harness positions with painter's tape. Install the new Control Unit and ran diagnostic procedure. The problem was solved. The washer is working fine.

the pump went out on the washer

  • Customer: amber from rochester, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
took the old part out by the front panel and put the new pump in and now it works great. only took a couple of minute to put the new one in. thank you for saving my washer.

Bellow had a tear in it water leaked out

  • Customer: Dwight from North Little Rock, AR
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I purchased the downloadable Maytag Maintenance Manual (PDF format) and followed some of the directions and pointers from this web site. All in all, it was a pretty simple process. 1) Take the top off - 3 metal screws, 2) take the control console and detergent dispenser out - 1 T-20 Torx screw and multiple plastic clips and 1 wire connector, 3) take the lower panel off - 3 metal screws, 4)take bellows retaining ring off -- spring retainer used a needle nose pliers, 4) take off door latching mechanism - 2 T-20 Torx screws and multiple clips + 3 wire connectors, 5) take front panel and door off - 4 metal screws, 6) remove bellows retaining clamp with phillips screw driver, 7) remove old bellows. Reverse the process to install new bellows. On installation, make sure that bellows drain holes are at the bottom of the door. Also, hardest and most time consuming part was installation of the metal retaining ring (spring retainer) fought with it for about a half hour before I finally got it on. BTW all metal screws for my machine were 1/4" head the remainder were all Torx T-20. Good luck!

F21 code

  • Customer: Mike from Columbus Grove, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Thank You so much for the other stories folks wrote on here! We were getting an F21 code on a regular basis. After finding a necklace and about $2.50 in change in the filter tray we found the problem. Over time I thought the washer was getting louder but it was so gradule that we really did not realize it.I had read other posts on here and ordered a new pump. After taking out 3 screws and 2 clamps the pump came right out and went in just as easy. Less than 15 minutes and we were back in business with a wisper quiet washing machine,Thanks Again everyone, Mike D.

F30 error code. Water pouring out.

  • Customer: Dennis from Waco, TX
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
A previous person had broken the actuator switch connection so I replace it and got rid of the error code. But water poured out and I eventually took off the whole dispenser assembly and found a sock had stopped the big hose up where it enters the outer wash drum.

drain pump impellar busted

  • Customer: jeremiah from royalton, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
I drained the water out of the pump area. Then took off all clamps and holding brackets. Next I pulled off the quick connect power plug. Then I put new pump in the way I took old pump out. The hardest part was unscrewing the bracket from underneath the washer. Cloth washer working fine.
All Instructions for the 11047512602
46-60 of 141