Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11042822201 > Instructions

11042822201 Kenmore Washer - Instructions

All installation instructions for 11042822201 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11042822201
91-105 of 207
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

tub would not turn

  • Customer: claude van from big sandy, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
take the back cover off and put belt on. the belt is a tight fit and requires sone effort, but can be done.

water was back filling into the tub when not in use

  • Customer: Larry from BONAIRE, GA
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Unplugged power cord, turned off both water valves on the wall, Disconnected the water hoses o the back where they are attached to the water inlet valve. Note: there will likely be some water left in the hoses. Then removed top lid of washer (this is a front load washer) by removing the 3 nut screws on the back of the lid and sliding it to the back and lifting off.. Disconnected the small hose that is attached to the water inlet valve by squeezing the hose clamp and sliding the hose off. Removed the 4 wires connected to the water inlet valve (marked each one with a number in order) then removed the Phillips head screw on the back of the machine holding the water inlet valve, sliding the valve to the right, . Removed valve, and replaced with new one, and re-installed by reversing order of removal.

Error codes SUD and Fo2

  • Customer: Gregory from LEXINGTON, SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump with the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good

Replace water inlet valve

  • Customer: Doug from ARROYO GRANDE, CA
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set, Wrench (Adjustable)
  • 1 of 1 people found this instruction helpful
Go to u tube video gives instructions. Very easy to replace

water inlet valve leak and hose

  • Customer: Paul from Big Torch Key, FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
disconect wayer inlet hoses.remove screws that hold the top cover. This will expose the water inlet valve. remove the defective valve and any other associated clamps,hose etc. test run for leaks.

Water Intlet Valve Stuck Open

  • Customer: MICHAEL from VALE, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
Shut water off to washer, unhook hoses, removed back panel of washer, removed screw that holds the valve in place then unhooked the water line that connects to the washer and removed part. Place new inlet valve in position and hooked hoses and mounted it in place, put back panel back on and hooked hoses up and turned water on. Did a test wash and it worked

one of the baffles came off

  • Customer: Tim from Kent, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
The design of the baffle assembly must be a little off. Seems that the baffles must come loose at the screw and it tends to cause the attachment nubs to wear. The parts were delivered in no time, had the screws to replace the old screws (which was cool) all in all, the install went without a hitch. Plus, the site is great, easy to identify parts and the order process is a piece of cake. Maybe your folks could come over and redesign our parts site!

water filled drum when off

  • Customer: Michael from Bear, DE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 2 of 4 people found this instruction helpful
so easy!!three screws to take top off,one screw held valve in take hose off then install new part and reverse take apart order and done!!!Would have been sick if had to pay service call for such a easy fix!! Mike

water backup when not in use, strip threads

  • Customer: Gary from Kenosha, WI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Remove top 3 screws.
Remove 1 screw that holds inlet valve.
slide valve to the right.
Mark and remove 4 connector wires.

Reverse order to install.

Washing machine wouldn't run. Kept making buzzing sound and didn't show door latched.

  • Customer: Keith from Amherst, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.

baffle broke off

  • Customer: Debra A. from Cinnaminson, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 5 people found this instruction helpful
snapped in place

Water in drum when not running

  • Customer: Kenta from Nashua, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Excellent instructions were found here and I followed them and it was quite easy. http://www.ehow.com/how_5934021_replace-water-inlet-valve-washer.html

WASHER WOULDNT DRAIN F21

  • Customer: Brenda from PLYMOUTH, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 1 of 2 people found this instruction helpful
REMOVE HOSES AND POWER PLUG REATTACH EVERYTHING AND THEN DONE.

broken latch

  • Customer: Hector from Richmond Hill, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 3 people found this instruction helpful
Unplug machine,remove three screws that hold on top cover.
Unplug latch switch assembly,then open front door of washing machine, remove three screws which hold latch
switch. Install in reverse order.

Washer posting a f6 error

  • Customer: Robert from Salt Lick, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 29 of 91 people found this instruction helpful
This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks
All Instructions for the 11042822201
91-105 of 207