11028812790 Kenmore Washer - Instructions

Your instructions were right on...! I looked just to prepare myself for the repairman, but after viewing your instructions and buying the part. I had it on in 30 mins. Thanks. It's nicke to know you're there for when something goes wrong. SDawson

Simply removed the agitator and replaced dog ears. Really easy!

the lid switch probably would have taken about an hour, but when I moved the washer, one of the water lines sprung a leak, then couldn't get it un-screwed from the falset, so had to cut a pvc line, put the falset in a vise and the falset broke, so had made 2 trips to town, and had to replace both water lines, one falset, and lots of cleanup, so it was an all day job, but the switch I started out to fix, was easy, and a good video for instuction was included.

After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this. Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.

Followed the video that was attached to the link where i ordered my part. Seriously, could not have been easier!! Thank you so much!!

After a little research on line, I knew to remove the fabric softener cup, pull out the clear plastic divider, unscrew the agitator bolt, pop off the construction clips, slide a plate down a bit, remove the old cogs, put in the new, return all the pieces to their places, screw the bolt back in place and now it works perfectly. I also bought a cabinet clip, spacer & screw that I will use at a later date. This repair went quickly and easily.

From the central column, pull off the fabric softener dispenser (of course, with the machine off). Reach in and pull out the seal (looks like a diaphram). Using a socket, undo the bolt and pull out the plastic ratchet assembly. I found the 4 dogs in bad condition, ordered them, and received them in a couple days. Replace the old dogs and reassemble. Only the bolt requires a tool. Much simpler and cheaper than I had anticipated.

i did the repair by myself but based on the video that part repair provided me with.

2nd time partselact has saved my ~13 year old washer for a total of ~40$ Entered the symptom and they told me more than likely what to look for and VIOLA ! Would've been easy to spend $200 each time my washer quit working but with a suggestion from a menu and even a video to show me how I revived my old $400 AMERICAN made washer to wash another day. Thank you part select !!

replaced the agitator directional cap by simply removing the top of agitagor. unscrewing a bolt, slipprd off broken peice, slid new peice in place, and rescrewed it in. Voila washer runs and agitates as it should

I watched a u-tube video from a repair man by the name of angel // this man is a detacated mechanic knows his job //used his diagnostics and the job was a piece of cake // he covers every aspect of all problems //// praise to angel ////

Very easy - less than 30 min. Followed installation video available on PartSelect website, except did not have to disconnect all hoses or lay on back. Left washer in place all connected and raised up on blocks about 6" off floor. Removed cabinet as per video instructions. Changed pump as per video instructions. Video from website was crucial to easy repair. Would not have known how to release cabinet latches and remove cabinet without video. Cabinet was off in 3 min. and entire job was less than 30 min.

Following the video posted with the part made this repair a piece of cake, well documented, filmed, great explanations of tools needed and how to do it all. This is a fantastic site for do it yourself people with a little bit of mechanical skills. BTW I've been a hvy. eqt. mech. for over 40 years so this is something different to tangle with and a lot cleaner. Thanks so much for your time and consideration in produceing this instructional video, and keep up the excellent work.

It was extremely easy and went very well. Installed new switch

Videos made repair simple and easy.Only difficulty was re-installing cabinet.Hard to align.