Models > 11028812790 > Instructions

11028812790 Kenmore Washer - Instructions

All Instructions for the 11028812790
1021 - 1035 of 1546
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
agitator not turning
all you have to do is watch the video, it does not get any easier then this.
Parts Used:
Agitator Directional Cogs
  • George from Wallace, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
the washing machine no spin
it was so easy to do. i just warch the instructions video clip from partselect.com
Parts Used:
Direct Drive Motor Coupling
  • linh from Palmdale, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No hot water
Followed the video, as simple as that..
Parts Used:
Water Inlet Valve with Mounting Bracket
  • Frank from Oceanside, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
clothes were not spinning out enough
Take off motor so the transmission comes out easier.You need to remove the agitator first.Took off old clutch and replaced it with all the parts that comes with the kit. Takes about 30-45 mins. Works great. The clutch didn't look like it was bad,but what a difference.
Parts Used:
Clutch Assembly
  • stephen from milford, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Was this instruction helpful to you?
Thank you for voting!
couplings were broken
just followed the really simple installation video provided.REALLY SIMPLE...
Parts Used:
Direct Drive Motor Coupling
  • lelo from atlanta, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Washer would pump water but the spin cycle got slower & slower
Because the washer was over 5 yrs. old I took this opportunity to thoroughly clean the machine also. I took the cab.completely off including the back. I then removed the agitator,motor & pump as an assembly. I was shocked at the sledge that had built up at the top edge of the plastic tub. A thin brush and the water hose took care of that.Next I removed the old clutch & installed the new assem. reassembled the motor pump & cab. Ran the machine in the garage for a cycle to make sure it operated properly without any leaks before I hooked it up inside. I was impressed with the how to video it was a real confidence builder when undertaking this repair, also the price of the part was good and delivery was prompt. Parts Select has a new customer.
Parts Used:
Clutch Assembly
  • Monroe from Great Falls, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
pump
order the part got it in 5 days, and installed it 10 min. Just had to removed two clamps and two hoses. Saved alot on a repair men. Easy job to do
Parts Used:
Direct Drive Water Pump
  • Don from Ormond Beach, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
would not agetate
it was a little more of a problum I have the stackables . It was a little harder to lay them on there back . everthing great for me . But you need to send the directoins with the parts
Parts Used:
Clutch Assembly
  • Robert from Round Lake Beach, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Spin cycle would not engage
Followed the steps on the Video that was post on the site. The repair was so easy I will keep this site in my bookmarked pages.
Parts Used:
Clutch Assembly
  • Robert from New Meadows, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drive Motor Failed, No Agitation
Website very helpful in visually locating and purchasing the part. Utube video also helpful. Took 30 minutes to disasemble and about 1 hour to reassemble. Works great! Biggest issue is laundry rooms are small spaces to work in and washer/dryer units are big! Thanks bill
Parts Used:
Direct Drive Motor Coupling
  • william from LOGANVILLE, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Drive coupling
removed clips holding water pump on , then removed 1/4 inch screws holding the clips holding the motor, removing the clips then. Replacing new coupling unit and reversing process.
Parts Used:
Direct Drive Motor Coupling
  • Dennis from Spokane, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
my washer wouldnt start when you closed the lid
I simply ordered my part and used the video provided on the web site to do the repair.I followed it step by step pausing it when needed.Im very grateful to this company.
Parts Used:
Lid Switch Assembly
  • Annette from Hollister, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't agitate
My wife actually figured out the problem, ordered the part, which came quickly. I watched the video and fixed the problem. I'm sure this saved us a lot of money. Instead of a technician coming out and replacing the part for about $200, it cost us $25 and an hours work. Thanks. You'll be hearing from me for future repairs!
Parts Used:
Direct Drive Motor Coupling
  • Terry from Gardnerville, NV
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
bad water pump
found the how to on youtube, did it right in the laundry room, got it done in the morning before i went to work,
Parts Used:
Direct Drive Water Pump
  • tony from moses lake, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Would not spin all the water out
Your video made it easy, thanks
Parts Used:
Direct Drive Motor Coupling Clutch Assembly
  • Frank from Torrance, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11028812790
1021 - 1035 of 1546
Back to Top