11021102012 Kenmore Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
was not agitating
Pulled the top off the agitator, used the pliers to pull off the seal, used the socket to get the bolt off , pulled the rest of the agitator off and replaced the directional cogs. Put it back together in reverse. Piece of cake. Beats paying a repair man.
Parts Used:
-
charles from grand island, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Agitator Stopped rotating, because the ends of directional cogs had worn down.
Lift off the agitator top with hands. Use socket with long extension to reach to center, unscrew bolt that holds the agitator to the shaft. Lift agitator out, slightly tap with hand so it will come apart to get to the 4 small directional cogs. At this point I used soap & water to clean all parts. I found the Thrust spacer was cracked. Ordered parts and they came in 3 days. You can just set the thrust spacer back in place using the diagram supplied with the parts. With the agitator upright I positioned the 4 cogs in place, and used a stiff wire to pull up into position, turned whole thing upside down, and matched the groves. I then flipped the agitator upright and set back in washer and bolted back into place. Works like new. Thats the way I did it. A good diagram is including with the parts.
Parts Used:
-
Cliff from Lexington, KY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
The parts were worn but i think it still needs the top agitator
Took the fabric softener despencer off and center cap untightened the nut and pulled up on top agitator and put the new replacement parts back. It seems to be working good
Parts Used:
-
Donnie from Phelps, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Agitator not agitating (spun freely)
I watched the short video that was in the email with my order confirmation and all turned out well.
Parts Used:
-
Kelly from Register, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Lid lock would not ingague.
Removed two brackets on back top of washer that hold top secure. Pulled top forward and up off off pins located on front top of washer. Located switch removed two screws holding it in. Then removed Panel on back of top in order to get to controls and unplugged other end of switch. Then reversed procedure and waher was back in service.
Parts Used:
-
Tom from Franklin, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Used machine, unknown age, with zero upper agitator motion. The upper agitator could be turned easily in either direction.
Age and condition of the washer were unknown. I had no agitator grease available. I went for just the replacement of the Agitator Directional Cogs. I reviewed the video for replacing the whole kit. Removed fabric softener dispenser and the seal below. The seal needed to be cleaned. Removed the 7/16" bolt with a socket and extra long extension. Removed the agitator. Pulled off upper agitator. The part that holds the cogs is in about the center of the upper agitator. It also needed to be cleaned. One original cog was broken the other were past needing to be replaced. Replaced the cogs and the retainer. There was some effort with getting the upper agitator down far enough to re-install the bolt. That was just a slight alignment issue. The other parts were put back in place.
Parts Used:
-
Calvin from Homestead, FL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!