11020992992 Kenmore Washer - Instructions

We received the part we needed in a timely manner. First we took the back off the washer and found out later we didn't have to, because you can access the pump from the bottom of the Whirlpool washer and when we turned it on it's back a brass colored pin about 2" long fell out and we have no idea where it goes.Looking around the bottom frame we saw another pin in a plastic little cup mounted to the frame and another empty cup .So we changed the pump easy,put the pin in the empty cup and the washer runs great! That's our story.Still don't know what the pin is for,it's not on the parts schematic.

1. Read many other repair stories for similar symptoms. PartSelect Forum was an excellent resource.

2. Posted my problem on PartSelect Forum and awaited reply. Read replies, and followed provided link to step-by-step guide for the procedure. PartSelect forum moderators were excellent advisors!

3. Performed the first half of the procedure to get to the diagnosed root cause. In some of the stories I had read, people had turned the washer on its back or tilted it up to get at the area from underneath. I am so glad I followed the conventional instructions, and left the washer standing and simply removed the cabinet. It was surprisingly easy. There's a reason why it was designed that way. I am also glad that I chose to remove the pump from the motor. While it is true that you don't *have* to remove the pump from the motor to get at the coupling...it hardly seems to make sense to remove the hoses instead. Removing the pump was incredibly easy, and by doing so, I never had to break any "wet" connections, and not one drop of water spilled over the course of the entire repair. (Even though I forgot to shut the water supply valves before I got started. Ooops! At least I remembered to unplug the power cord.)

4. But despite the open valves, the galoshes came into play not for their ability to repel water, but for their value as an electric insulator. I wrapped the galoshes around the handle of a long screwdriver when I discharged the motor's capacitor. :)

5. Ordered parts. Washed clothes in sink. Waited. Washed more clothes in sink. Waited some more. Washed more clothes in sink. Waited still more. Came very close to stopping payment to PartSelect because the very simple, commonly-requested part I ordered, which was supposedly in stock on the day I ordered it, didn't ship until the day it was supposed to arrive--even though I paid extra for expedited shipping. And I was never sent an e-mail to warn me that the parts were going to be delayed. And then to top it all off, rather than make up for some of the lost time caused by their own error, and ship it overnight, PartSelect chose to ship it 2nd day. All that good will generated by the excellent website completely evaporated by the failure to correctly complete the simple tasks that the business has needed to be good at since before computers were even invented. I will never use PartSelect again.

6. Prying the old coupler halves off of the motor and the washer took some effort, but was not overly difficult. I wound up removing the motor mounting plate in order to get better access to the half that was stuck on / needed to be attached to the drive train of the washing machine. Mounting plate was a breeze to remove and attach with a socket driver. I used one of those stubby flat-head screwdrivers to pry the old parts off. This was the one time where I thought it might have been easier to have the washing machine tilted up or on its back...but I muddled on through without even removing the bottom panel, and it wasn't too awkward. I used a large socket and a full-size hammer to not-so-gently tap the new parts into place. Putting all of the parts back together took a bit longer than it took to break them down, but it was easy. The instructions for putting the electronic control panel into test mode had been rolled up and taped to the cabinet inside the top panel. After I put the cabinet back on, I used those instructions to test all the cycles before fastening the top panel and testing the machine with an actual load. So far, so good...

Part Select provided the problem determination information and the video on how to install the replacement parts. I ran into one problem, I could not remove the lock nut to remove the inter and outer tub. I should have bought the special wrench for $14, no local DYI or hardware store had the wrench. So, after examination I used a large screwdriver and wood block to lift the tubs up just enough to remove the old pads and replace with the new. The old pads showed only a wear, but was enough to spin the tubs off balance. The new tabs made the washing machine work like new. New washer $500, repair man $150, parts and information from Part Select $20 bucks, priceless.

Removed the washing machine from the wall and found a broken spring on the floor. Began disassembling the unit before accessing your sight. (Later I viewed your video of the more simple dis assembly).Used your parts breakdown to identify the 6 parts I needed (3 springs and 3 retainers),and ordered them. They arrived on time and as per the video, installed them with ease and reassembled the unit. My wife is very happy. Thank you, Rusty

leaned and propped washing machine back to get access to pump, removed hose clamps and hoses,removed retainer clips, old pump was stuborn to remove but was able to pry off motor with screwdriver. sanded rust off metal shaft,put on new pump,replaced retainer clips, replaced hoses and clamps. set washer in upright position removed aggitator cap, used 7/16' socket with long extension,unscrewed bolt, pulled off aggitator sleave, removed cog unit, replaced cogs, put sleve back on and tightened bolt. I had the machine outside so I hooked up a water hose and an extension cord, put machine on small load and tested machine . worked like new. also when i finished the test I had noticed earlier that my hose screen had a mineral build up, cleaned that by lightly scraping and used little rust inhibitor that also tackles scales. total time was about 30 minutes. Wife is happy now and I was rewarded later.

The tub was out of alignment and water fell behind it and onto the floor. My brother-in-law suggested my problem could be the tub balancing spring and when I moved my washing machine, there it was on the ground.
The schematic does not show where it hooks up. So after I did what I thought looked right, the machine still did not work properly. Then I replaced the three suspension springs and that didn't solve the problem.
I found a whirlpool "do-it-yourself" repair book at the library and was prepared to tear into the machine. However, I did not have the tub balancing spring in the correct spot at one end. It hooks up from one of the outer bracket to the back of the housing unit along between the legs. There is a hole that had rusted through. I simply drilled a new hole nearby and low and behold it works!
Easy fix - the frustration was with the poor schematic.

First, I removed the softner cup from the top of the agitator. Second, I removed the plastic seal by pulling it out. I then used a socket to remove the bolt holding the agitator down. I then removed the agitiator from the machine and seperated the upper and lower agitator by placing my feet on the lower agitator and pulling up. The dog-ears were in the upper agitaotr section and easy to see and replace. I re-assembled in reverse order. The whole process took less than 30 minutes.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

First I turned off the water and unplugged the washer from the outlet. I took the two screws off the console and turned it up to undo the clips that hold the cabinet to the back. I took out the 2 phillips screws at the top corners of the back. I was then able to pull cabinet off and not have to remove the console, but carefully slid it to the side, as ther wires were still attached.
Pried off agitator cap & reached into agitator to pry out another cap to access 7/16 bolt. Checked over the agitator parts for wear (dogs) Took agitator, top outer (white) and inner (brown) tub rings off.
Sprayed lots of liqid wrench around spanner nut and drive block and gave it time to work. Used spanner tool to get spanner nut off. Hard work. Pounded and pounded and pounded and pounded with hammer. It gave a tiny bit. Then I got an idea: I pounded it back the other way, as you would to tighten. This helped. I then pounded back the other way and did this again. It worked amazingly well.
Got to drive block and it was rusted out along the bottom and also hard to get off. The diagram showed a "lock" (horseshoe shaped thing) on top of it, but mine was all in one piece but I couldn't tell that. I sprayed and pryed and pounded from the bottom and it split in half. It needed to be replaced anyway.
The inner tub was also hard to get out and I used some dish liquid. I pushed down, (using the rags here, the edges can cut you). I twisted, I pulled. I pushed, I pulled, I cussed, and begged. I then went to bed and then next day I pushed backwards and forwards and side to side & finally it came off. Then I undid the brackets on the bottom of the outer tub along the bottom and disconnected the clear hose in back. When loosening the black hose clamp in front to the pump, water started to come out of the hose so I grabbed a cool whip container to catch it. It smelled yucky. Once I had the outer tub off I put the new seal in, using some plumber's grease to help get ithe tub over the shaft..Then I hooked up the hoses & brackets on the bottom of the outer tub. I cleaned out the outer tub, as there was crud in the bottom. Then I poured about 5 gallons of water in it to see if the seal was set in right. Make sure the drain hose hasn't fallen out! (You can leave this water in the tub, you'll find out why) I cleaned up the rust on tube of the inner tub with steel wool and inspected everything else. Something didn't look quite right about the outer shaft that goes around the spin tube. It looked like something should go there. I discovered there SHOULD have been a seal there but one was never put in. So I put one in. I used a little grease to help put the new drive block on, and tightened the spanner nut with the spanner wrench. I put everything else back on EXCEPT for the cabinet-with the console attached. Ha Ha All the other directions I read wrote to take the console off first. If I had done that I wouldn't have been able to do the most important part of the job: testing the result. I finished filling the tub to the lowest water level to watch it go thru it's cycles and checked for leaks. If the console was "flopped over" the back how can you check? (I don't play with wiring)
I turned off the water & unplugged the washer and slid the cabinet on.. I tipped the console back to access the large gold squiggly brackets that hold the cabinet to the back and reattached them to the back, by removing them, hooking them onto the back, and snapping them into place. I double-DOUBLE checked to see if anything had come loose, then slid the console first on top of the back and put the two screws back in. The screws on my machine are not covered up by the end caps, but they are at a wierd angle, so I held the console up slighly and started the screws first. As they tightened down the console slid into the holes on the cabinet.
There is a small sppliance shop in my town & the guy loaned me the spanner wrench. It was very nice of him.I guess I will have to give his & his famil

Unplugged power cord and disconnected water lines; note which is hot/cold. Washer was then tipped on its front. Discharge hose was disconnected. Washer was then rolled over onto its back as this would put the pump on top for much easier removal.

Pried off two clips attaching pump on motor using a flathead screwdriver. The rear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.

Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.

Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.

Replaced clips to hold motor on transmission and reinstalled screws holding clips.

IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!

Attach pump onto motor and replace clips. Double check everything is back in place.

Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.

First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.

1) Unplugged electrical cord
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamps.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]

I had a little difficulty at first, trying to remove the back of the unit. I then figured out that the repair was to be made by leaning the washer back and removing it from underneath. That became really easy as the bottom is open.I had to remove one nut and then the agitator from inside, then tilt the machine back, disconnect the two hoses from the pump, remove three bolts and lower the motor/ transmission assembly. Then I had to disconnect the motor from the pump ( with two snap on clips) and remove the broken plastic coupling. The new coupling had a metal insert that seems to make it stronger than the original piece.I then just reversed the procedure to put it together again and it worked fine. The part was shipped immediately and I got it sooner than I expected so I greatly appreciate that. Overall it went well, and by the way, it was my daughters washer and she was happy as well.Thanks, Roger

Removed top cap on agitator w/ flathead screwdriver. Removed protective cap over bolt and cog housing shaft. Used 7/16 deep socket w/ extension to remove bolt. Removed housing where stripped cogs were located. Cogs seated loosely in shaft housing no tools required to remove cogs. Replaced cogs in housing, made sure everything was lined correctly. re-inserted housing into shaft. ,screwed bolt, replaced caps and works like new.

Read on Internet to diagnose and get at part.
Luckly they sent new fill hose along with level control switch
as that was problem. Visually there was no
kink or blockage. Upon removing hose, I discovered
a slit on hose which did not allow pressure
to actuate diaphram. I installed new switch
and never thought to return as savings instead
of calling repairman was a no brainer !!!
Word of caution " never force"when removing or
installing a part. It should be easy Steve, Ca.

turned the washer on it's back and shoved the tub to the side to release pressure on a spring ,pulled it loose and installed new one. this worked for the back two then turned washer on it;s face and repeted the process on the front spring.
Washer works great now.