Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11010502990 > Instructions

11010502990 Kenmore Washer - Instructions

All installation instructions for 11010502990 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11010502990
1,396-1,410 of 1,812
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water pump quit workding no water would drain

  • Customer: Tim from Whitesburg, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I was very happy the part arrived very fast and just what we needed, and service was super.. We took the old pump off slipped the new one into the slot and hooked the clips back on it and tighted it up and plug the washer back in and filled with water and it drained... We started doing laundry right away, and so far so good... Tired to leave a review but it won't let us into the site, but we would use the same company to order from again, thank you so much...

No cold water

  • Customer: Adam from Castaic, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I did a you tube search for "no cold water in washer" and found a video for what the fix is. Afte disconecting the power and water hoses it was Unbelievable how easy it was. Two screws in the back to open it up which I watch on a you tube video which was from part select. Then two spring clamps to open the inside and expose the water valve.. One screw and a hose clip and the valve was out. Did the reverse and put it back together..

Water pump was leaking

  • Customer: Michael from Spencerport, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair video was great. I decided not to remove the outer cover as there is room to get to the pump if the washer is tipped back. The pump was easy to fix with the exception of the root cause of the failure. There was water getting to the pump shaft and over time it rusted and expanded in the pump housing causing it to split and leak. Once the old pump was removed, a file was needed to reshape the drive shaft to allow the new pump to be installed. Not bad on a 16 year old washer!

The agitator top did not turn

  • Customer: Michael from Columbus, OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
The Whirlpool website provided an excellent repair video, showing a step by step procedure for making this repair. I did have to clean the old parts but other than that i just followed the video. I used a socket to loosen a single bolt holding the agitator,I pulled it apart, replaced the cogs, and then put it back together.

Spin cycle would not complete or spin fast enough

  • Customer: Evan from Batavia, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Replaced Cltch assembly. Hardest part was figuring out how to drop the motor. The clutch is located of the main shaft above the motor, under the drum. Three bolts hold the motor in from underneath, however there is a bolt at the top of the shaft in the agitator assembly. Note location of the snap ring on the shaft holding the clutch assembly, grooves in shaft. The only other issue that I had is the is a triangular metal peice that is not attached in anyway between the drum and framing. It had moved when I had the motor and had to be reset after I did my first test run of washer. Spins out great now!

Agitator wouldn't turn

  • Customer: Simone from Danville, ME
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the agitator and the broken directional cogs. Ordered the new ones; recieved them within a couple of days. Replaced the cogs; in no time the washer was working like new.

washer agitator wasn't working properly

  • Customer: Francis from Valley Lee, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I followed the video clip that showed how to make the repair that was attached to the email sent from Patrselect notifying me that my part had been shipped. The video clip was excellent and no other instructions needed. Thanks

top portion of agitator free spinning

  • Customer: gregory from camp hill, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Removed center top cap/sofetner dispenser. Removed center shaft bolt. Pulled off the top agitator section from bottom portion. Inside the upper agitator is the inner housing for the cogs, pushed right out. Remove cog retainer plastic ring. Careful, the cogs freely fall out and it a little tricky when reassembling. Reassemble every (cogs go in only one way), place the upper agitator back down and over lower portion in machine. Now Put the bolt back in place. Here's the tricky part. You will need a magnetic tip driver or socket to hold the bolt until you have it started because it sits in recessed "well" area. I used a dab of regular Elmer's glue from bolt head to socket. Worked like a charm. Be careful not to over tighten bolt. Remember, upper agitator should free spin one direction and "catch" in the apposing direction.

Spin cycle not working.

  • Customer: Thomas from Brighton, MI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Almost identical to the instruction video that was sent. Very straight forward. I did not take apart the washer to identify the problem. I was short on time so I took a chance and ordered the highest probability cause of the symptoms indicated by your website. It was dead on; the problem is fixed. Parts were received ahead of schedule. Excellent all around.

Washer was not spinning clothes on 1st spin

  • Customer: Jeff from Westfield, IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After researching possible failure modes and reviewing a video for teardown/access from the control panel and access top down I noticed a lot of 'break dust' on top of the transmission. Shorting out the lid switch and putting my little finger on the drum, it would not spin but the clutch was spinning fine. I ordered a new clutch... Interesting thing when I was taking the clutch out... the gear it was attached to slid right off! After figuring out it was too big to go 'back' into the transmission and reviewing the parts explosion diagram... it BELONGED INSIDE THE TRANSMISSION! So I took the transmission cover off, poured out out the black-ish oil with metal filings in it, put the gear inside, filled it back up with 10W30, put the lid on, added the new clutch while it was apart and finished reassembly. Wow! It spins much better than when it was new. I guess never assume what can happen on an assembly line. Thanks for the great site.

washer not spining

  • Customer: Israel from san antonio, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
took motor of 2 screws instaled motor coupling

Machine would not get up to speed on spin cycle.

  • Customer: Larry from Franklin, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Started by unpluging and disconnected water hoses.Removed agitator retaining bolt and pulled off. Tipped machine onto a support on it`s front side. Unplugged motor connector and removed drain hoses from pump.Removed the three motor bolts and rotated and pulled out motor and shaft. Removed retaining clip and installed new clutch assembly. Plastic clutch drive looked ok but since it was apart removed retaing clip and changed it too. Slid shaft and motor assembly back into machine and reconnected everything,works like a new one.

Broken Lid Switch

  • Customer: Ryszard from Morrison, CO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Follow Video Instructioon

switch burnt up and fell apart

  • Customer: james from thomaston, GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
removed the old one and replaced it with the new one. the ground screw on the washer was rusty and caused the only problem. delivery was super fast, the part was exactly like old one. good job parts select.

The washer would not spin.

  • Customer: Edward from Buhler, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered the part and it was delivered in 3 days! I viewed the video again and installed the lid switch. It was just that easy. It went exactly per the video! I will use PartSelect the next time I have an appliance problem. I figure I saved at least $100.00 and got it done in less time (shipping and all) than the repair people could get me in! Thanks PartSelect!
All Instructions for the 11010502990
1,396-1,410 of 1,812