10656566400 Kenmore Refrigerator - Instructions

Follow the video.

I just wanted to tell about the good service they gave to me. The first one I received was broken, and with one phone call they sent me another, no problem. Installation was take the broken one out and replace it with the new one.

Turned off the water to the ice maker; disconnected the wiring harness to the ice maker; unscrewed it from the freezer (two screws). Unhooked the ice lever bar, opened up the motor assembly. Switch the motor out (two screws). Installed in reverse order.

removed the broken shelf and replaced it with the new one

If you are having this problem, read this. My refrigerator door would not stay closed. This was over a year and a half time period. I thought it was something complicated and told my wife to call a repairman. Thank goodness she does what she does best - not listening to me! I finally had enough and went online and googled my problem and found PartsSelect. PartSelect had a repair video showing how to fix the problem. If you are like me, I'm very cautious about purchasing from a website in which I'm not familiar. PartsSelect is a reputable site (I promise I do not work for them). My refrigerator is over 8 years old and they had the part I needed, a lower door cam, along with a video on how to install the part. This honestly took about 5-10 minutes to do and I did it without any help. I was so aggravated at myself for waiting so long at doing this!! I actually ordered 2 of these parts, just for the next time. You can do this.

Pulled out the icemaker. Switched out the Motor Assembly (so easy) and woke up the next morning with ice. Our ice dispenser wasn't working either. This repair inspired me to take the ice dispenser apart and I found that the lever arm wasn't touching the contact when pressed. We now have ice and a working ice despenser. Oh yeah--my wife was so impressed. The part came in on time and it was very very easy to replace.

It is was easy to repair and just as easy to order from parts direct.

Per the video, easy out & easy in.

Once we figured how to get front off, it was like a puzzle. One piece at a time. So thankful part has been improved and replaced. It works better than before, just wish would have done it sooner.

I pulled the refrigerator away from the wall, unplugged the electrical cord, and turned off the water going to the refrigerator. I then removed the cover on the bottom rear of the refrigerator by removing 7 or 8 small screws. Luckily the new and old valves were exactly the same except for some color coding. There were 2 screws to remove that attached the valve to the body of the fridge. There were 3 plastic tubes that connected to the valve and 2 wiring harnesses that plugged in. Before removing them, make sure to note which tubes and wires went where. The 3 tubes on the old valve were the push in type, just like the new one. I could not pull 2 of them out like the instructions said. I had to pry them out with a screw driver. In doing so I warped about 1 inch on the end of each tube which I then cut off with a razor blade. The electrical connections pulled out easily. I then pushed each tube back into the new valve which was very easy and pushed the electrical connections in. I attached the valve to the fridge with the 2 screws, turned the water on, plugged in the electrical cord, and checked for leaks. I put the back cover on and was back in business. It took me about 40 minutes but when I was younger could have done in in half the time.

Remove inside door trim plate. Then removed three screws that held in the light assembly. The only difficult thing was reconnecting the temperature adjustment rod. After replacing this rod you must slide the temperature control slide to midway and this hold the rod in place while reinstalling the light assembly. If I were to do it again it would probably take me half as long.

simply slid the new part in place...really simple

Unpluged the refrigerator. Removed the cover on the control unit by inserting a screw driver under the metal clips. Removed the three screws frrom the front of the control unit. Pulled toward the back of the refrigerator on the metal loop which turns the icemaker on and off and it came loose where it goes into the control unit. Wiggled the unit and it came free. place the new unit in approximately the right position. Reached into the icemaker and moved the ice eject leavers so the shaft would enter the control unit with the flat side of the ejector in the right position. Gently pushed the control unit into its place and aligned the screw holes. Replaced the three screws. Inserted the wire shut off loop into the hole on the back of the control unit housing. Pluged in the electric. The ice maker worked.

Followed instructions on video on website. Very easy to do. Removed old part, put in new and it took all of 15-20 minutes. Had ice in approximately 1 hour.

You saved us a bunch of money again! We love you!