10656536400 Kenmore Refrigerator - Instructions

Verified that the sensors were working. After removing the Ice maker assembly from the sliding track, I found that the indexed drive wheel on the motor had broken off from the shaft mounting. I ordered the Icemaker control and motor assembly from Partselect and swapped out the bad part. It only has three screws to remove and replace so it's fast and easy to fix.

Water was not filling the ice tray and the ice tray coating was comming off. After the service repairman wanted to charge me over 500.00 for just replacing the ice maker, it told him to take a hike. I bought the icemaker and the electronic controls, which controls when and how much water goes into the tray for less than 250.00 and it took me less than 15 minutes to replace.

We were afraid of breaking the new part.But after watching the repair video about how much pressure to apply the part snapped right in. Thamk you for the video it helped alot.found the part quick and easy and it was shipped fast to us problem solved.

just removed tho old one and inserted the new one job complete.

Push it in to place very easy.

Remove ice storage container from inside freezer. Remove philips screw from the coupler underneath ice storage container. Removed coupler and flat washer. Installed new plastic coupling and metal flat washers. Relaced original coupler and screw. Tighten screws very carefully. Installed ice storage container and filled it with fresh ice. Ice is now coming out when the level on the outside of the freezer door is pressed. Yeah...

The problem with our ice maker started when it stopped making ice. It was a hit or miss problem. One day it would make a bin full then couple days later none. One morning I noticed that there was water overflowing from the ice maker which froze inside the freezer. I ordered the maker and valve after watching the videos on this site. With those videos I was able to fix the problem in no time. Ice maker has been working properly for over a week now. My wife was ready to get a new fridge but I was stubborn and wanted to see if I could fix it. Thank you to partselect.com for the fast shipping and great instructional vids.

Pull the ice maker out using a nutdriver Pull the use a srew driver to remove the srews did the same to replace it put it back in had ice in 20 min

Removed old crisper tray and inserted new crisper.jod done

After googling for a parts supplier, PartSelect.com came up. The site was well done and had the Parts List conveniently available. I watched the associated video which was the highest quality "how-to" repair video I have seen. As it turns out, though, the icemaker does not have to be removed from the freezer unit. I removed the icemaker's shutoff lever, removed 3 screws, pulled the motor assy off, slid the new motor assy in place and re-installed 3 screws. Reinstalled the shutoff lever per the video and JOB DONE.

I opened the refrigerator door, being careful to leave the freezer door closed. After verifying that refrigerator light was on, I squatted down to be at the same level as the crisper drawer. Firmly grasping the old crisper drawer by the convenient built-in handle, I pulled the drawer until it was fully opened. I removed the contents of the old crisper drawer, noting the original location of each item, so that I can place the contents into the replacement drawer in the same place. Grasping the old crisper drawer, I pulled outward and lifted slightly until the drawer was off the track and out of the refrigerator. Using both hands, I placed the rear of the new crisper drawer against the drawer track, lining the tabs on either side so that they would enter the track. I applied gentle, rearward pressure, guiding the new crisper door onto the track. This step was a little tricky. I had to wiggle the new crisper door up and down a bit, to get the new crisper door past the "stop bumps" in the track. After the new crisper door was sufficiently in the track to be supported by the track, I replaced the contents in (what I thought) the same locate from which they were removed from the old crisper drawer. After placing all contents back into the new crisper drawer, I applied a little more rearward pressure until the new crisper drawer was in the fully closed position. I then closed the refrigerator door. I quickly reopened the refrigerator door, to ensure the light went out. It was on. I slowly closed the refrigerator door, keeping an eye on the gap between the refrigerator door seal and the refrigerator cabinet, and noted the light did, in fact, go out when the door was about a half inch from being fully closed. Returning to a fully standing position, I announced to my wife that I repaired the broken crisper drawer. The congratulated me on my accomplishment and I felt a rush of satisfaction over a job well done.

Ordered a new Ice Maker and replaced old one. The installation was a breeze except for the water recepticle on the right side of the Ice Maker. It was taller than the original and difficul to move the rubber water line into the new recepticle. Other than that. Problem solved. Been working great ever since.

First gasket received was damaged. Returned for full credit, no problem. Got second gasket and THEN found the real problem was the hinge! PartSelect accepted second gasket for full credit. No problem, no hassle. Awesome customer service. Thanks PartSelect!

Very easy to install. Followed instructions so took about 1 minute (including unpacking). Saved big money. Great company to deal with

This fridge is s ultraease 2 its 8 years old. Icemaker would'nt make ice. Its fairly easy all you do is take out the screws i recommend a power drill tho. Pop out the cover put the new motor in. I did'nt hear anyththing or see anything for a hour or two thought it did'nt work. Then i heard a clunk like ice falling into a bin. 3 hours later ice was falling frequently.