10651109110 Kenmore Refrigerator - Instructions

Found the control bracket housing had broken and micro switch for the water pump was not making contact with mechanical link. (In other words when you put a cup under the dispenser and push water did NOT come out.)

I removed the faceplate and switches, removed all the switches and installed them in the new control bracket. Installed new control bracket into fridge and tested. Works! Reinstalled faceplate and switches and drained system for a few minutes. Man I forgot how good filtered water tasted!

nothing to repair, simply removed the old ice container and auger from the freezer and replaced with it with the new one.

took back of refrigerator, removed water lines, removed electrical connections. removed 2 screws holding water valve, replaced water valve, replaced electrical connection, replaced water lines. Put back on refrigerator. Tested water on freezer door. Didn't work, had to take refrigerator back off again and check the electrical. I didn't get one of the connection put on securely, Put back on refrigerator, check water on freezer door. It worked. Make sure the electrical connection are connected this will sav you about 10 minutes of repair time

Removed food itmes on broken shelf. Removed old glass shelf cover. Removed broken shelf bracket. Installed new shelf bracket. Intalled new glass shelf cover. Replaced food items back on shelf

I removed the outer ice/water dispenser cover following directions I found on-line (push down and gently pry out at the bottom). I then removed several nut-head screws which were holding a plastic plate which had the door light and electric control wiring mounted in it. Behind that I found a broken tab on the Control Bracket which was why my water dispencer was not working and I found the chute door for the ice maker was chewed up which allowed warm air into the chute and was causing my ice build up problem. Replacing the Control Bracket was easy. Just note how things come apart. Putting the chute door in was a little more complicated, but again, note how things come apart and you should not have a problem putting it back together.

a simple replacement

Removed four screws from ice maker motor/light support.Then unplugged electrical plug from side of freezer.Used two slip joint pliers to remove coupler from motor shaft. installed new coupler to shaft hand tight as will tighten as motor is run.Then reversed tear down order.
Ice dispenser works better than when we first got the refrigerator

I removed the Ice door front cover on freezer door. Found door pivot was broken. I installed door pivot bracket, and dashpot in kit. I used most of the kit to repair it. The door now works like new. Thanks for the right parts Frank

Turn off the fridge and unplug the power. Inside the refrigerator unit, remove two plastic panels extending from the front to the rear cooling vent by unscrewing two screws. Gently unhook the thermostat tube from the rear vent.

On the control panel, gently pry off the two control knobs and the front control panel. Remove four screws to drop down the control assembly. Unplug the left electrical connector and unscrew the lever control arm being careful not to bend it. Disconnect the right side electrical connector and you can now remove the control unit to a table to easily work on it.

Undo two screws to remove the thermostat bracket. Undo two more screws to remove the thermostat assembly. Install the new thermostat and reverse the process just described. It takes about 15 minutes if you know what to do ahead of time. You will have to reuse the plastic tube that covers the thermostat sensing tube.

The design of this refrigerator door (it's a side-by-side) is somewhat unbelievable. The door is designed to hold things, yet when you do the weight of the door wears out the lower door cams. The cams are designed to "complete the door closing", i.e. when you gently push on the door the cam mechanism takes over. When the cams wear, the door fails to close. Note to others - you may mistakenly think that the failure of the door to close is related to the seal; it is not.

The repair is quite easy; remove the upper cover, using a not driver (socket), then remove the upper door bracket. Make sure you hold the door or have someone else hold it. After the fasteners are removed gently lift up on the door and remove it from the lower cam assembly. You will see two plastic cam pieces; one on the lower bracket and one on the door. Both need to be changed to effectively "renew" the door closing mechanism. Once the cams are replaced the door can be reassembled to the refrigerator.

Unplug refridge, shut off water supply, remove backing. Remove two screws holding in valve, pull out valve and remove water lines. Have towel to wipe up very little water that leaks out. Unplug electric sources, remove old valve. Take new valve , plug in electric sources, push in water supply until they bottom out, attach bracket to back of refridge. Replace backing, turn on water supply, plug in and bleed lines.

The part to fix this was a $50.00 part.
I purchased this Bracket Dispenser for $6.00 and it fit on My fridge perfectly. I just used the screw hole that was a little higher on the water dispenser. Simply cut off the broken end / or Buy a new Hose (Cost at Lowes about $6.00) guide hose along the bracket and use a socken set to reinstall the screw. Water is not squirting on people any more.

Replaced upper cam piece on bottom hinge and also replaced pivot thimble on upper hinge.
No problems, except pivot thimble glued in place. Had to cut up and pull out with pliers. Everything works like new now.

Removed six screws from cover in the back of the freezer. Removed old fan . Removed power wires from old motor. Unclipped old motor from the mounting bracket. Replaced old motor and reversed the rest of the parts. Done

At their site was ordering each piece by # and cost and it was adding up to be costly. Went to partselect and was doing the same and up pops the ice door kit. Was a little wary because my original had a heater tape to it. Got the kit and installed not a problem at all. 100% satisfied would recommend to anyone.