10650203992 Kenmore Refrigerator - Instructions

Undid the bolts to the ice maker, unplugged it and took it out of the freezer. Removed the cover, unplugged the motor and unscrewed the motor from the casing. To install new motor screw it into the casing, plug it in and replace the cover.

Heard double clicking sound every couple minutes. Unplugged unit then using a coil brush, cleaned all dirt, lint, everything from bottom of fridge. Finished with vacuum cleaner. Located start relay. It was on the left side of the compressor. Pulled relay straight off of compressor, much like a plug from a wall. Unhooked two wires from relay. No need to disassemble old relay. Parts received from partselect.com go back onto compressor individually. Using the instructions provided, from the kit, select the correct parts for your unit and carefully attach them to the compressor. Plug in the wire to the relay, then following the instructions, attach the jumper wire and plug into the relay. The cover in the kit is a little tricky to put on but it will fit. Took me about 15 mins and the hardest part was getting the old part off. Plugged unit back in and it started right up. 24 hrs later, everything is working great!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Watched video of repair. Took all drawers and drawer holders out of freezer to acesss back panel. Removed 6 screws from back panel,slid up and out. Cut 2 wires to remove old bi-mtl defroster. splice the wires and attached new bi-metal def.

Using instructions found on the internet and the illustrated parts breakdown it was just a matter of following instructions.

Very easy you pullup and the old bin snaps out.Then you align the new bin to the notches on both sides.then very easily push down on the new bin.And the job is finished.

Told Wife To Watch The Instructional Movie, Got Me A Beer And Watched Football. She Finished In about Thirty Minutes.Good Job

The icemaker on oour Kenmore was fading fast. Ice was only being harvested once every 4-5 hours instead of every two. Then finally it stopped altogether. I did some research and decide that it was the motor assembly that needed to be replaced. I ordered the part and within 3 days it arrived. Within 45 minutes I replaced the part with the assistance of the youtube video. I am not a Mr. Fix-it but this was fairly straight forward. I am now a hero.

internet search

Took two screwdrivers and inserted bottom of bezel pryed up and out gently. Removed (4) screws and unpluged (3) electronic plugs removing the circuit board. After you remove bezel & circuit board you have a chance to see what you are doing and get to the problem area with more ease. Remove old parts and reverse it putting the new parts. Process is very simple just pay attention to the order everything was removed. On my frig one of the plastic ears that hold the pin which holds the spring and door was broke. The piece I needed was no longer avaliable. I had to use a piece of the plastic from the old parts I removed, drilled a hole the size of the pin in it and glued it to the broken off ear. Put everything back together and I am pleased to say that everything works fine! So you might need to go a little MacGyver on it. All in all very simple fix.

Popped the cover off took panal off to access ice door screws.Removed old parts and replaced with new kit.Works fine now.

Removed the nut holding the plastic cover plate at the top of the door. Removed the 3 nuts holding the latch to the fridge. Lifted the door up and laid it on its' side. Removed the nut holding the door cam and replaced it with the new one. removed the nut holding the lower door cam and replaced it. Put a little vaseline on both cams and re-in-stalled the door. Took less than 15 minutes and the door is like new. Watching the video on the web site was perfect.

Removed food from door. Shut off fridge. Removed dust cap at top hinge. Marked location of top hinge with masking tape so lining up when reassembling would be easier. Removed screws holding top hinge to fridge. Removed door, placed on blanket&towel. Removed old door cam. Put on new door cam. Removed old hinge cam. Put on new hinge cam. Put door back on. Replaced top hinge, lining up with tape. Replaced dust cap. Note that door did not really self close very well until it was filled with food. By far the hardest part of the whole operation was that my wife wanted to clean the fridge in the process!

Removed flap and three screws holding tray. one screw holding plug protector. Slid tray out and unplugged . Removed three screws holding control & motor assembly.Put new unit in reassembled.

removed facial then the board replaced the lever retainer and reversed process very easy when part's are correct also shipping time fantastic good job 5 stars thank you