Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10644252400 > Instructions

10644252400 Kenmore Refrigerator - Instructions

All installation instructions for 10644252400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10644252400
481-495 of 756
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Wrong valve bracket

  • Customer: David from Petersburg, AK
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I completed the ice maker installation but the bracket the automatic water valve was attached to in no way would fit my Whirlpool fridge. The one showed in instructions sent with the ice maker was different than the one Partselect sent me. I had to grind both sides of the bracket off and just hot glued it to the spot where it was supposed to go. I can see how this could be a real issue for some.

Refrigerator Door would not close on its own

  • Customer: Enrique Pulido from Miami, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Set out an area large enough to lay the door down once I took it off the refrigerator. Took off the top screws and hinge. Had my 12 year old so help me with the door and hand me all the tools so I could quickly change out the parts and not leave the Refrigerator open for too long. I think from the moment we took the door off to the moment it was back on was probably about 5-6 minutes tops. That is how easy this was. All the parts fit and thank you to PartSelect and it great website that advised me of the second part that went with the first if not I would never have known. Thanks again!!

icemaker went out

  • Customer: Larry from Heflin, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took old one out with a screw driver,replaced it with the new one. works great!. din't have to put part on at back bottom.I will say this.you guys sure got the part here fast! thanks..

the guide rail broke off would not let the drawer slide

  • Customer: CHARLES from Fairmount, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just removed tho old one and inserted the new one job complete.

Busted drawer

  • Customer: susan from fort mill, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Push it in to place very easy.

Refrigerator would not cool.

  • Customer: Bruce R from Beaufort, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Did some research on internet. Order part. Replaced part. New problem now. After running about 15 hours, the ground fault circuit gets out. And again the refgrigerator stops working. Reset ground fault circuit and after about 15 mins. it starts working again. Not sure what is causing the problem now. Anybody have any suggestions?

Guide slot had broken off and was difficult to slide

  • Customer: CHARLES from Fairmount, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old crisper tray and inserted new crisper.jod done

Crisper Drawer was cracked.

  • Customer: David from Henrico, VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I opened the refrigerator door, being careful to leave the freezer door closed. After verifying that refrigerator light was on, I squatted down to be at the same level as the crisper drawer. Firmly grasping the old crisper drawer by the convenient built-in handle, I pulled the drawer until it was fully opened. I removed the contents of the old crisper drawer, noting the original location of each item, so that I can place the contents into the replacement drawer in the same place. Grasping the old crisper drawer, I pulled outward and lifted slightly until the drawer was off the track and out of the refrigerator. Using both hands, I placed the rear of the new crisper drawer against the drawer track, lining the tabs on either side so that they would enter the track. I applied gentle, rearward pressure, guiding the new crisper door onto the track. This step was a little tricky. I had to wiggle the new crisper door up and down a bit, to get the new crisper door past the "stop bumps" in the track. After the new crisper door was sufficiently in the track to be supported by the track, I replaced the contents in (what I thought) the same locate from which they were removed from the old crisper drawer. After placing all contents back into the new crisper drawer, I applied a little more rearward pressure until the new crisper drawer was in the fully closed position. I then closed the refrigerator door. I quickly reopened the refrigerator door, to ensure the light went out. It was on. I slowly closed the refrigerator door, keeping an eye on the gap between the refrigerator door seal and the refrigerator cabinet, and noted the light did, in fact, go out when the door was about a half inch from being fully closed. Returning to a fully standing position, I announced to my wife that I repaired the broken crisper drawer. The congratulated me on my accomplishment and I felt a rush of satisfaction over a job well done.

changing a broken fridge part

  • Customer: Samir M. from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very easy to install. Followed instructions so took about 1 minute (including unpacking). Saved big money. Great company to deal with

Cracked bin and side rail broke

  • Customer: Shirley from Glendora, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received new drawer in 2 days and effortlessly exchanged it for broken one. Color of writing didn't match but I just removed it from the old one and replaced it. Very pleased.

The refrigerator would not defrost and would freeze up and no longer cool.

  • Customer: Mike from Frankfort, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.

Refrigerator door would not close properly

  • Customer: Charles from Riverside, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
I removed the upper hinge cover and then the the hinge itself. Then lifted the door off the lower hinge peg. I placed a blanket on my pool table and positioned the door on it. The bottom screws were a little difficult to get the nutdriver seated so I used a quarter inch drive with socket to remove the screws. The replacement Closing Cam was quickly inserted and reassembled the hinge and lubricated with vaseline. Next I removed the Door Cam that was still on the peg on the refrigerator (it was completely worn flat). Quick work for this too. I tried to set the door back on the pivot hinge but eventually I needed another person to guide the door onto the peg. Reassembled the top hinge and voila, the door works just like new.

Broken crisper drawer

  • Customer: Donald D from Kennewick, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply slid the replacement into place. 30 seconds at most.

Loud fan motor

  • Customer: Brian from Saint Augustine, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed lower plate on back of refridgerator and changed out fan. The video was great and made the repair a snap. Fan is quiet and no more overheating refridgerator.

Broken vegetable drawer . Broken plastic front

  • Customer: Edgar from West Babylon, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I just changed old drawer to new drawer
All Instructions for the 10644252400
481-495 of 756