10642106301 Kenmore Freezer - Instructions

After watching videos how to replace went very easy.removed ice maker cut wires replaced switch put back together now working ok so far.

1) Went to site. 2)Read trouble shooting section for recommended replacement part. 3)Selected part. 4) Watched detailed installation video on part specifications. 5)Installed part. Refer runs like new. (Note: May have to restart installation video if audio does not work the first time.)

Replaced gaskets on both doors. Followed the online video link that came with emailed receipt. Worked exactly like demonstrated in the video.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

replacement went easy most of the time was spent removing the ice build up

Followed the video instructions.

Pulled the refrigerator out from the wall, I had unplugged it prior so it didn’t burn out the compressor. Put both new pieces together, I ordered both just in case they were both bad. Used the screwdriver and removed the screws from the bottom cover. Removed the silver wire thing, unplugged the wire connector and pulled out the old piece. Plugged the wire connector into the new piece and pushed the new piece into the silver prongs, replaced the silver wire thing, put the back on the refrigerator and replaced the screws and crossed my fingers.
Plugged it in, turned on the refrigerator and freezer on from inside the refrigerator and joila it started right up and is working. I am a 63 year old female, and had watched the video first on how to remove and replace it.

The gasket has an inner lip that fits over the edge of the door plastic liner. The old gasket was removed by pulling it straight out, in the plane of the door. Try not to pull sideways as it could crack the door liner, which gets brittle with age. The new liner had a brown magnetic strip, which holds the door closed, and this fits behind the edge of the door liner. Start on the bottom of the door. A helper is useful to hold the gasket loosely vertical. A flat blade screwdriver can be used to pry away the liner to insert the new seal. Once you have worked in the lower edge, install both sides, and then the top. Some juggling side-to-side may be needed for an exact fit

Removed door and replaced bushing bracket was ok.

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

Make sure you order the right parts. The bar needs 2 caps so don't make the mistake of only ordering one. Once you push in the end caps into the retainer bar, gently insert bar into slots on door. Right parts will create a perfect fit.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

The bent hinge caused a bad seal which let in air into the freezer, so there was a ton of frost build up. I ordered the parts, and they came in 2 days! I figured what tools I needed, got my wife to help hold things, and in 20 minutes it was like new.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks