Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10641519100 > Instructions

10641519100 Kenmore Refrigerator - Instructions

All installation instructions for 10641519100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10641519100
466-480 of 764
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

replaced oven lightbulb

  • Customer: peggy ann from forest city, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very easy

Refridgerator door would not close easily.

  • Customer: John from Battle Creek, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I unloaded the door, removed the cap covering the screws at the top hinge. I removed the screws then lifted the door off the pin. Next I removed the screws holding the door cams in place. Replaced both cams and screws, set the door back on the pin then reinstalled the three screws at the top. Snapped back on the cover and I was done. Door works perfectly.

rocker switch broke off

  • Customer: STANLEY from OAKLAND, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

Both fans running/No cooling/Compressor hot & Not running

  • Customer: Jeff from Belfair, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First I checked the compressor, very hot to the touch & not running. I unplugged for a few minutes to cool & when I plugged it back in, it started for maybe a second or two. Then I unplugged the relay from the compressor and new instantly it was fried. So I decided to google the issue which led me too partselect.com and I then realized this relay is called the start device/Relay and it also provides overload protection for the compressor. When I received the part or parts in this case, they came in a small box which included 2 combo relays, 2 overloads, 1 ptc start relay, 1 jumper wire, 1 electrical cover, 1 instruction sheet. By using the number on the compressor I was able to see that I needed to use the ptc start relay & one of the 2 overloads which plug onto the compressor & I needed to use the white jumper wire as the terminals were a different size on the ptc relay. At first I was a little confused because I unplugged one relay and the replacement was two separate parts. Had to read instructions carefully several times to make sure I was using the correct overload and ptc relay. I plugged in the fridge to test & it worked great so I unplugged and installed the electrical cover, reinstalled cardboard cover on back of fridge & I was done. Two weeks later fridge is working great!! Hope this helps.

The ice machine quit working.

  • Customer: Jean from Valley Mills, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It was so easy. This is the second Ice maker we have put in this fridge. Thank you very much.

Protective cover for bulb had melted

  • Customer: Lee from Brooklyn, NY
  • Difficulty: Very Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

Plastic Broken Drawer Needed Replaced

  • Customer: Brandon from Avondale, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took old one out put new one in and its like new! Costs for a simple drawer was $75! Expensive but the transaction was simple!

The refrigerator would run but would not always come back on after de-frost mode.

  • Customer: Larry from Burkeville, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the installation video on "Parts Select". Unfortunately I watched it twice b/c the first part ordered last October only lasted 4 months. This part seems to be alright as the refrigerator has been running for approximately 6 days now - so far so good.

Door no longer 'self' closes

  • Customer: Richard from Granite Falls, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replacing the door closing cams, starts with emptying the door of all foodstuffs. Remove upper hinge cover. While supporting the door, remove three upper hinge screws with the nutdriver. Lift upper hinge from top and lift door off lower hinge pin. Remove the cam retaining screws on both the bottom of the door and the lower hinge pin. Pry (if needed) the worn cams from their position. Install new cams making sure to line up the screw holes. Re-install screws, tightening just snug. Lift door back onto lower hinge pin. Set upper hinge back in place with screws loosely installed. Check door gap, top to bottom to ensure proper alignment. Tighten upper hinge screws and re-install hinge cover. Check door for proper function.

Refrigerator door would not close by itself

  • Customer: William from Apex, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I've replaced the door cams in the past, but they didn't last very long. I finally realized on my own that both parts need to be replaced at the same time. One piece is on the case-side of the bottom hinge and the mate is on the door-side of the bottom hinge. They both have a ramp shape, with door ramp riding up the hinge ramp as you open the door. The ramp shape makes the door want to slide back down the ramp to close automatically. These are plastic parts that wear out over time. If you don't replace both at the same time, the ramp shapes don't match and they wear out quickly. They are inexpensive parts, so always replace both at the same time. I added a thin layer of petroleum jelly to help them glide better. Hopefully this fix will last a long time. It's extremely easy. First take off the top hinge of the door. Then lift the whole door off the bottom hinge. You can set it on a chair with the bottom hinge hanging over the edge of the chair. Replace the two parts, one on the door bottom hinge and one on the refrigerator case bottom hinge. Easy as pie. The only tool needed is a nut driver. You need a helper to help lift and balance the door while you work on it.

broken crisper drawer sides

  • Customer: Joe from Williamsto, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
took out the old one and replaced with new. PERFECT FIT.

I had a crisper drawer that was cracking in the middle

  • Customer: Donna from Omaha, NE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
First I used some glue to stop the crack from spreading, and that worked for a while, but then I deceided to get a new replacement part. What I got was better than the original one as it had a white protective piece over the end of the drawer and I believe that will give more protection to the drawer. My kids did not always close the drawer all the ways and that is how the crack started. So now the refrigerator looks like new again.

Old ice maker not working right

  • Customer: Dorothy from Yuma, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Per instructions

Not cold very warm

  • Customer: Thomas from Hooksett, NH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Took the cover off the relay parts with pliers removed the relay replaced bad part with the new parts and put the new cover back on plug the refrigerator in and it started to cool off and it is running great so far . A 46 dollar parts and it saved me a lot of money and it only took 15 min. Thank you

Wrong valve bracket

  • Customer: David from Petersburg, AK
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I completed the ice maker installation but the bracket the automatic water valve was attached to in no way would fit my Whirlpool fridge. The one showed in instructions sent with the ice maker was different than the one Partselect sent me. I had to grind both sides of the bracket off and just hot glued it to the spot where it was supposed to go. I can see how this could be a real issue for some.
All Instructions for the 10641519100
466-480 of 764