Switch to Classic
Models > 10571-2 > Instructions

10571-2 General Electric Range - Instructions

All Instructions for the 10571-2
61 - 71 of 71
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken heat element
Fit was perfect, slip right in prlace and works great thank u! R.e.Rice
Parts Used:
Surface Element - 6 Inch - 240V
  • robert from wernersville, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
the paint started to chip off.
remove the door, removed about six screws and did a clean up on the glass. the replacement part was screwed back in place. so easy
Parts Used:
Bottom Trim - White
  • vanessa from runnemede, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Wrench set
Was this instruction helpful to you?
Thank you for voting!
Burner bowls had been used and abused for year gone by in this rental.
Replaced them all. Next I want to replace the burners.
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Diane from Rio Rancho, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
bowls were worn out
Open the box and inserted the bowls
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • frances from winston salem, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
uneven heating of oven
This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!
Parts Used:
Oven Sensor
  • John from Sandstone, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
slot that heating element fits was worn down and caused burners to be uneven
replaced with new ones
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Judith from Broadway, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The range kept giving an F2 alarm
When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.
Parts Used:
Oven Sensor
  • Les from Coal Creek, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
6" and 8" burner bowl replacement
Slide out burner elements. Remove old burner bowls. Insert new burner bowls and reinstall burner elements.
Parts Used:
Burner Bowl - 8 Inch Burner Bowl - 6 Inch
  • Shawn from Lubbock, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Right Oven Door Handle End Cap Broke Off
Went on line and watched a couple of instr. videos which were very well done and explained just how to replace the end cap. I purchased and relaced both end caps and was able to clean the entire handle before putting it all together. Looks really good now. Thankyou. JJM
Parts Used:
Door Handle End Cap
  • James from Fort Myers, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
the center of the element had broken
just pulled the old one out and replaced with new one. very easy
Parts Used:
Surface Element - 6 Inch - 240V
  • Betty from Fayetteville, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
welded supports for the surface elements were broken
unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.
Parts Used:
Surface Element - 6 Inch - 240V
  • Thomas from Montgomery,, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 10571-2
61 - 71 of 71