All Installation Instructions for General Electric Range 10571-2

just needed new GE burner bowls

Only instructions I have has nothing to do with installation. But I'd like to suggest that you find a better shipping method. Placed my order on Feb. 7, received message later same day that it'd shipped. I didn't receive it until Feb. 16th -- very poor delivery service.

Parts Used:

Burner Bowl - 8 Inch

Burner Bowl - 6 Inch

Jacqueline from E WENATCHEE, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Part rusted over time...22 years.

Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.

Parts Used:

Bottom Trim - White

Jeannene from HUNTINGTON, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

replaced door handle and end caps

the first end cap broke when I tried to tighten the screws, the end cap holes were too small, Thirty some dollars down the drain. Drilled out the second end cap before I tighten the screws, worked fine. Make sure you drill out the holes of the end caps or they will split out and you lose your money. There are no warnings about this problem.

Parts Used:

Door Handle

Door Handle End Cap

Thomas from COXS CREEK, KY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Both end caps were broken removed

Removed torx head screws. Removed broken pieces of the end caps. Replaced the handle installed the end cap screws.

Parts Used:

Door Handle End Cap

Johnson from LUFKIN, TX
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bottom trim piece on 24 year old stove had rusted. Replace trim piece was still available.

Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.

Parts Used:

Bottom Trim - White

Donald from FAYETTEVILLE, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The trim piece on the bottom of the door was rusted making the unit look really dirty and used.

It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.

Parts Used:

Bottom Trim - White

Glenn from West Melbourne, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

rusted trim strip

remove screws, re-install screws

Parts Used:

Bottom Trim - White

Larry from Sarasota, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

old unit failing to heat all coils

I first removed the unit by pulling gently from connection. Replaced the new one in that same manner - simply inserting into connection.

Very easy, I'll probably try it again soon.

Parts Used:

Surface Element - 6 Inch - 240V

Emma from The VIllags, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Melted plastic colander on a burner

I simply replaced the element. HOWEVER, the most wonderful parts of this repair...Because of the pictures and closeups and descriptions I knew exactly 'what' to order! And I had the replacement in less than 24 hours. I can do some home repairs but this company provided such detailed information AND speed of delivery...that this was a no-fuss fix. I'll definitely stop by to buy, again. Thanks!

Parts Used:

Surface Element - 6 Inch - 240V

Paula from Dyersburg, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

bottom trim had rusted out from water build-up

disassembled bottom trim on oven door.cleaned area of excess rust and installed trim piece.

Parts Used:

Bottom Trim - White

john from buford, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old burner bowl needed to be replaced

Took out the old & put in the new one-Done!

Parts Used:

Burner Bowl - 8 Inch

bonnie from N KINGSTOWN, RI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

a plug on the element broke off while cleaning and replacing

Absolutely no tools required for this task. Simply align the prongs to the female portion on the stove top. Carefully push in until the element is in place then line up with the drip pan slot. No instructions are necessary!!

Parts Used:

Surface Element - 6 Inch - 240V