Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve a...
This is a blower motor for your range, but you may also know it as a blower fan motor or a downdraft vent fan motor. This part is used with down draft models. It helps draw the steam and odors through...
$228.69
In Stock
Order now and your part arrives in 2-3 business days!
This exhaust vent blower wheel is almost seven inches in diameter, and just under four inches deep. It is made entirely of metal and is used with a range's venting system.
$90.87
In Stock
Order now and your part arrives in 2-3 business days!
This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the elec...
$10.94
In Stock
Order now and your part arrives in 2-3 business days!
This is an authentic OEM part from Briggs and Stratton and Snapper for use with Generators. The fuel tank mounting grommet forms a cushion between the fuel tank and the fuel tank mounting bolts. The m...
$5.19
In Stock
Order now and your part arrives in 2-3 business days!
This is an authentic item that is supplied by the original equipment manufacturer for use with Toro lawn and garden equipment. It is a standard hardware which has multiple applications depending on th...
$7.70
In Stock
Order now and your part arrives in 2-3 business days!
The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached spri...
$25.41
In Stock
Order now and your part arrives in 2-3 business days!
This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cov...
$3.99
In Stock
Order now and your part arrives in 2-3 business days!
1. Turn off power to range at circuit breaker 2. Remove grate 3 Remove control knobs 4, Remove two screws holding control panel 5. With wrench, remove locking nuts from control switches 6. Lift panel, exposing switches 7. With new switch in hand, unattach old switch one terminal at a time, attaching new swi
... Read moretch exactly as old switch, terminal by terminal. 8. Replace everything in reverse order 9.Turn on power
Just removed the broken vent cover. Injected foaming sealant. Pushed on the vent cover plate. Screwed it in place. More foaming sealant. Clipped on the flapper and secured the cover.
Important: Down load the helpful assembly diagram for the fan motor and study it for a few minutes. It's very straight forward. Also a good idea is to remove the bottom panel which comes off easy before starting.
My only problem was removing the existing blower/fan wheel without damaging it once I had the assembly on the work b
... Read moreench. It was rusted on tight and managed to remove after a few tries using penetrating oil. The wheel is in stock and I'd suggest buying a new one along with the new motor if I had to do the job again.
Bottom line; the fan motor fit perfect but did have to re-use part of the old existing electric pig tail because the motor does not come with the factory type motor terminal connectors. By using three twist on wire connectors was back in business. The down draft vent works like new.
