Maytag Dryer Belts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Maytag Dryer Belts
Your Price
$13.95
In Stock
Maytag Dryer Drive Belt
PartSelect Number PS346995
Manufacturer Part Number 341241
This dryer drum belt (Whirlpool Dryer Belt, Drive Belt) has four ridges, three grooves and is 1/4" wide, and 92 1/4 inches in length. It comes in black and is made of rubber. The belt transfers the rotation of the motor to turn the drum. The belt attaches to the drum, idler pulley, and motor pulley.
Fixes these symptoms
- Drum Not Spinning
- Heat stays on after drum has stopped
- Noisy
- See more...
Installation Instructions
Ray from Denton, TX
Dryer tub belt broke
Removed the two screws that attatch the lent channel to the top of the dryer, then lifted the top of the dryer by pushing in on the two locking tabs located at the front , left and right , corners of the dryer top with a small flat head screw driver. The top of the dryer will fold back out of the way. At this point I removed the two 1/4 inch screws that are located on the inside of the dryer front left and right corners that hold the front panel/door to the two side panels. Now I was able to lift the front panel up and set it to the side. The bottom of the front panel that contains the dryer door that I just removed was held on the bottom by two clips that slide into slots on the front panel and did not require any removal to disconnect the bottom of the front panel, just pull up on the front panel. Since the tub was held in place by floating on a seal at the back of the dryer and a seal on the front panel , which I just removed the tub is now free floating except for the two alignment roller wheels at the bottom of the tub. It is easier if you lay the dryer on its back at this point with front of the tub pointing up. I pulled the tub out and cleaned the years of built up lent and removed all the pieces of the old , destroyed, belt. Note, the belt tentioner is located at the front of the motor which on the bottom right hand side. If your belt is broke like mine the tensioner may/will fall to the back of the dryer when you tilt it back, but do not worry. Once the dryer was cleaned up I put the tub back in place , still on its back and made sure the two alignment rollers were in place and rolled freely when the tub was turned by hand. Another note, my original belt tensioner did not have a rolling wheel that the belt rode on , but was a semi-circle smooth surface that the belt remained in constant friction with when the dyer was running, so I made sure the replacement tensioner I ordered with my new belt did have a rolling wheel that the belt would ride on, which I believe will reduce wear and extend the belt life. The new belt came with a diagram of the belt and tensioner routing which was helpful. Note: do not take the tensioner wheel off/apart when trying to route the belt. Follow the instructions routing diagram. The tensioner is held in palce by inserting the bottom back half into the slot in the bottom floor of the dryer making sure it is aligned with the belt pully on the shaft of the dryer motor. The dryer is still on its back side. Now, it was easier for me to route the belt around the center of the tub, following the marks from the original belt, and hold in in place in a few spots with masking tape and then route it thru the tensioner and onto the front pully of the motor. Make sure you have the grooves of the belt against the tub and the grooves are aligned with the pully on the motor. Now you can remove the masking tape that was holding the belt around the tub and spin the tub by hand watching the belt making sure it is not in a bind and is traveling around the motor pully , tensioner and tub freely. Make sure the tub is still sealed on the back side wall. As you turn the tub by hand you can adjust the belt by hand so that is following the original marks around the tub left by the orignal belt. Also double check the two alingment rollers and make sure they are spinning and on track. Now put the front panel with the door on by sliding it onto the two clips that are one the bottom at each side and put the two screws in that hold the front panel to the two side panels. Now stand the dryer back up and spin the tub by hand again making sure it has a good seal on the back side and on the front panel. Pull the top back down and put the two screws in that hold the lent channle to the top. I am not sure when the belt started failing on my dryer, but was amazed at how quiet it runs now. Guess I was use to the extra noise made by a dryer that was about to die. This was a cheap and easy repair and glad I did it myself.
Read more...
Your Price
$35.95
In Stock
Maytag Dryer Repair Kit
PartSelect Number PS373088
Manufacturer Part Number 4392067
The Whirlpool Dryer Repair Kit is a universal maintenance kit for 27-inch dryers, compatible with various models from Whirlpool, Kenmore, Maytag, and others. It includes a belt, drum rollers, an idler pulley, clips, and a washer to fix common issues like noise and improper drum rotation.
Installation requires disassembling the dryer to replace parts using standard tools. Ensure the dryer is unplugged before starting. This durable OEM kit provides reliable repairs for quieter, more efficient operation.
Fixes these symptoms
- Drum Not Spinning
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
jason from HOLDEN, MA
very loud squeeling sound
The issue was the idler pulley. First I began opening up the front panel based on a youtube video but soon realized the model was slightly different and required a lot more items to remove. I saw the pulley in the back with nothing in the way so I put the front panel crap back on and removed the rear panel. There it was, very simple to remove and replace. I'm not looking forward to drum rollers though. Hopefully they're aren't as difficult as they appear.
Read more...
Your Price
$22.95
In Stock
Maytag Dryer Multi Rib Belt
PartSelect Number PS382430
Manufacturer Part Number 661570
The Drive Belt is a 93 1/2" belt which wraps around the dryer drum to allow tension and movement. If broken the dryer will not turn properly, or there may be loud noises. The part is rated as "medium" difficulty to install. Refer to your model number and user manual to ensure this part is correct for you. To complete this repair you will need a Phillips screwdriver, 1/4 inch nut driver, a putty knife, and a pair of needle nose pliers. Ensure you disconnect your power to the dryer before beginning this repair, which should take between 30 and 60 minutes maximum to complete.
Fixes these symptoms
- Drum Not Spinning
- Noisy
- Won’t Start
- See more...
Installation Instructions
Lucas from Nuevo, CA
Need it a new pulley and belt
I did the repair all by my self and just payed for the parts.
Read more...
Your Price
$23.95
In Stock
Maytag Dryer Tumbler And Motor Belt
PartSelect Number PS11757542
Manufacturer Part Number WPY312959
The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in color and it is made entirely of rubber. If your dryer will not tumble, is noisy during operation, or will not start you may need to replace the belt. To complete this repair, you will need to remove the front panel as well as the drum. You will need a 5/16 nut driver and a stubby Phillips screwdriver to complete the repair. Be sure to disconnect power to the dryer before you begin this repair. During the repair, make sure the belt doesn't fall into the groove in the drum, which will cause it to be too loose. You should be able to access the belt and replace it by removing the front panel and bulkhead.
Fixes these symptoms
- Drum Not Spinning
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Raymond from West Bend, WI
electric dryer was rumbling - wheel or belt?
Unplugged dryer. Front came off easily. Removed front of blower. Wheel came off fairly easily - could then see that shaft of motor was circular with flattened side but inside of old wheel was rounded. New wheel popped right on. Took tumbler off so I could clean lint out more easily and get a good view of how the belt threaded through. Put the tumbler back on and reached back with both hands to thread it. Took a half dozen tries until I was sure it was seated correctly and not twisted. Put front... of dryer back on. So far (a week or so) the rumble is gone. Seems blower wheel was the cause of the rumble. Belt didn't seem worn but replaced anyhow.
Read more...
Your Price
$24.95
In Stock
Maytag Dryer Multi Rib Belt - 91-5/8 Inches
After removing the screws to the front door and panel I removed the wires to the door switch. Carefully I removed the belt and removed the drum. I took the time to vacuum all of the lent from the inside and and remove from all the wiring, motor and heating elements, etc. I replaced the drum rollers, belt, front glides and a buzzer that was on the blink. I reassembled the dryer and unforetunately the dryer was still squeeking. I later repeated the process and found that the tensioner wheel for the belt was the culprit. I cleaned then greased the bearing portion and replaced it. I reassembled the dryer a second time and now it's quiet as a mouse. By the way, you will need a rivet gun to replace the front glides and I recommend you give the belt tensioner wheel a good inspection the first time.
If your dryer is squeeking, go ahead and order the tensioner wheel also, it's a little money spent toward making sure you get rid of the noise! It might save you a lot of time and trouble. Read more...
PartSelect Number PS11741110
Manufacturer Part Number WP33002535
This multi rib belt spins the dryer drum during the drying cycle. This belt is 91-5/8 inches in length, 3/8th of an inch wide and has five ridges. It is black in color and made of rubber. You may need to replace the belt if your dryer is noisy or will not tumble.
Fixes these symptoms
- Drum Not Spinning
- Noisy
- See more...
Installation Instructions
Mark from Lafayette, LA
Dryer squeeking loudly becoming worse quickly
I received my parts promptly and had no problems, they were accurate and fit well. After removing the screws to the front door and panel I removed the wires to the door switch. Carefully I removed the belt and removed the drum. I took the time to vacuum all of the lent from the inside and and remove from all the wiring, motor and heating elements, etc. I replaced the drum rollers, belt, front glides and a buzzer that was on the blink. I reassembled the dryer and unforetunately the dryer was still squeeking. I later repeated the process and found that the tensioner wheel for the belt was the culprit. I cleaned then greased the bearing portion and replaced it. I reassembled the dryer a second time and now it's quiet as a mouse. By the way, you will need a rivet gun to replace the front glides and I recommend you give the belt tensioner wheel a good inspection the first time.
If your dryer is squeeking, go ahead and order the tensioner wheel also, it's a little money spent toward making sure you get rid of the noise! It might save you a lot of time and trouble. Read more...
Your Price
$13.95
In Stock
Maytag Dryer Multi Rib Belt
Vacuumed inside of dryer (full of lint.) Read more...
PartSelect Number PS11742271
Manufacturer Part Number WP40111201
This dryer drum drive belt attaches to the motor pully and works the drum as the motor rotates. The belt has a length of 93- 3/6 inches, and wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pully. Replacing the rib belt could solve symptoms such as a screeching noise when the dryer tumbles, a broken belt (dryer will not tumble if its broken), no heat or not enough heat, or the dryer will not start. The tools needed for this repair are a nut driver and a putty knife. Remember to unplug the dryer before installing the part and protect your hands by wearing gloves.
Fixes these symptoms
- Drum Not Spinning
- Noisy
- See more...
Installation Instructions
Robert from Skokie, IL
Replace drive belt
Remove front panel, lint basket, motor mounts,exhaust hood, front drum brackets. Then slip serpentine belt around drum, pressure w/ tension idler pulley and slip around drive motor spindle. Replace all parts in reverse order (a two person job).Vacuumed inside of dryer (full of lint.) Read more...
Your Price
$47.95
In Stock
Maytag Dryer Belt
PartSelect Number PS11750135
Manufacturer Part Number WPW10198086
This authentic OEM drum belt is designed to fit with various models of dryers. The belt is a narrow strip of rubber that wraps around the drum and connects it to the dryer motor. This allows the drum to rotate smoothly and circulate warm air evenly through the drum. If the drum belt is faulty the drum will be unable to turn, you may hear unusual grinding, scraping a banging noise, and the belt itself may be frayed, cracked, or hanging loosely off the drum. If the belt is no longer able to support the drum, it should be replaced promptly to prevent further damage to the dryer and ensure it continues to run efficiently.
Fixes these symptoms
- Drum Not Spinning
- Noisy
- See more...
Installation Instructions
Wayne from Woodbridge, VA
THE DRYER HAD A HUMMING NOISE THEN NOTHING KNOWING THE MOTOR HAD JUST BURNT OUT
PULLED THE DRYER APART TO GET TO THE MOTOR , REMOVED MOTOR , LOOKED FOR MODEL NUMBER OF DRYER AND DID RESEARCH ON WHERE TO BUY THE MOTOR AND BOUGHT FROM PARTS SELECT BECAUSE BOUGHT FROM THEM BEFORE
Read more...
Your Price
$72.22
In Stock
Maytag Dryer Drum Belt
PartSelect Number PS11748388
Manufacturer Part Number WPW10112954
This drum belt is for dryers.
Drum belt attaches to the motor pulley and spins the drum as the motor rotates.
Unplug the dryer before installing this part. Wear work gloves to protect your hand
Fixes these symptoms
- Drum Not Spinning
- Noisy
- See more...
Your Price
$33.95
In Stock
Maytag Dryer Drive Belt
PartSelect Number PS11748749
Manufacturer Part Number WPW10131172
This drive belt is genuine OEM part for your dryer. The belt works with the idler pulley to spin the dryer by driving the drum, and can become worn or break over time. To complete this repair, you will need a screwdriver, putty knife, and socket or nut driver. Accessing the belt involves disassembling the front panel of the dryer. Make sure your new belt is not twisted when installing it on the drum.
Fixes these symptoms
- Noisy
- See more...
Your Price
$47.95
In Stock
Maytag Dryer Belt
PartSelect Number PS11731121
Manufacturer Part Number W10849499
Get your dryer back in top condition with our Whirlpool Dryer Drum Drive Belt. This genuine OEM part is designed specifically for select models of Whirlpool, as well as other select brands including KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef. Our Whirlpool belt directly attaches to the motor pulley, effortlessly spinning the drum as the motor rotates. Please, bear in mind, even though parts may appear the same, sizes and shapes can exhibit minor variations. We recommend unplugging the dryer before installation and wearing work gloves to protect your hands. Remember to verify the part number matches your model for seamless installation!
Fixes these symptoms
- Noisy
- See more...
Related Maytag Dryer Parts
- All Maytag Dryer parts
- Maytag Dryer Brackets and Flanges
- Maytag Dryer Caps and Lids
- Maytag Dryer Circuit Boards and Touch Pads
- Maytag Dryer Doors
- Maytag Dryer Drums and Tubs
- Maytag Dryer Ducts and Vents
- Maytag Dryer Elements and Burners
- Maytag Dryer Fans and Blowers
- Maytag Dryer Filters
- Maytag Dryer Fuses
- Maytag Dryer Handles
- Maytag Dryer Hardware
- Maytag Dryer Hinges
- Maytag Dryer Hoses and Tubes
- Maytag Dryer Knobs
- Maytag Dryer Latches
- Maytag Dryer Lights and Bulbs
- Maytag Dryer Panels
- Maytag Dryer Pulleys
- Maytag Dryer Seals and Gaskets
- Maytag Dryer Sensors
- Maytag Dryer Springs and Shock Absorbers
- Maytag Dryer Switches
- Maytag Dryer Thermostats
- Maytag Dryer Timers
- Maytag Dryer Valves
- Maytag Dryer Wheels and Rollers
- Maytag Dryer Wire Plugs and Connectors