Magic Chef Dryer Drums and Tubs

Magic Chef Appliance Parts
Shop By Part Type

Popular Magic Chef Dryer Drums and Tubs

Your Price
$9.45
  In Stock
Drum Glide
★★★★★
★★★★★
(10)
PartSelect Number PS11741931
Manufacturer Part Number WP37001298
If your dryer is noisy, will not tumble, or is leaving marks on your clothes, you may need to replace the drum glide. The drum glide is installed on the front bulkhead either at the top or the bottom, regardless of the brand of dryer. To gain access to the drum glide, you will have to open the cabinet on the dryer. This drum glide is sold individually but it is important to note that they should be replaced in pairs. Before beginning this repair, it is important to disconnect the dryer from the power source. The tools required for this repair are a putty knife and a 5/16 nut driver.
Fixes these symptoms
  • Marks left on clothes
  • Noisy
  • Will not tumble
  • See more...
Installation Instructions
David from Underwood, IA
Loud banging sound. Worn out roller.
Pulled off the lower panel with 5/16 socket.Pulled off the door assembly by removing the two screws at the bottom of the door assembly. I pulled down a little and then out. be carefull of the wires. Other posts said to remove. The wires were long enough I did not have to remove them. I just leaned it against the wall. I then removed the 4 screws that hold the front piece in.pulled it off replaced brackets , installed self adhesive felt(stuck good) and then glides. Mine were thin but not the problem. I then reached under the drum and released the belt from the tensioner. I then pulled the whole drum out.This is the time to vacum out good. I could get to the rear rollers very easy. The left roller was shot and the shaft half wore into(the problem). I pulled off the two screws holding the roller support. Normally You have to remove the wheel with snap ring pliers first to remove the support. In this case snap ring long gone. Replaced support shaft, installed thrust washers and roller with grease for both sides. The right support shaft was still good. Removed tensioner pulley and inspected. It was just as good as the new one. Cleaned and greased and reinstalled. Put new belt on the tub and slid it back in. Be carefull to get the belt on the proper side of the tensioner. I then installed the front supprt in place to support the tub with the 4 screws. Spun the tub(felt good) then reached under and reinstalled belt to motor and tensioner. Spun again to check for belt alignment. (Check) Reinstalled door an lower panel. Test Quiet Sounds like new. Very easy! I hope this helps someone just as the other post has helped me. Blessings to all. Read more...
Your Price
$48.83
  On Order
Two-Piece Split Ring Bearing
★★★★★
★★★★★
(7)
PartSelect Number PS334199
Manufacturer Part Number 279441
This is a replacement bearing ring kit for your dryer. The bearing rings are found on the top and bottom lips of the dryer drum. If your dryer is unusually noisy, or the drum will not turn during operation, or if there are marks left on your clothes after a cycle, you may need to replace the bearing ring kit. The kit comes with 2 bearings, one for the top and one for the bottom of the dryer drum. Remove the front panel of your dryer to access the dryer drum for this repair. At this point you can use a pair of needle nose pliers to release the old bearing rings from the drum. Snap the new bearing rings on, and reassemble the dryer to complete your repair.
Fixes these symptoms
  • Marks left on clothes
  • Noisy
  • Will not tumble
  • See more...
Installation Instructions
Edward from Andover, NJ
Dryer was sqeaking loudly when running
I Looked on internet sites for this type of problem.
Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I had also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.

Edward Brennan
Read more...
Your Price
$32.78
  In Stock
Cylinder Glide Bracket
★★★★★
★★★★★
(1)
PartSelect Number PS11741912
Manufacturer Part Number WP37001036
These brackets support each side of the tub. Order quantity needed.
Fixes these symptoms
  • Marks left on clothes
  • Noisy
  • Will not tumble
  • See more...
Installation Instructions
Jeffrey from Medina, OH
Noisy - Clothes getting stuck between drum and bulkhead
1) Removed lower panel
2) Removed door
3) Removed Front Panel - removed connectors from switch and marked connections
4) Removed Front Bulkhead
5) Glides and Felt pads were missing, and brackets were nearly worn through
6) Removed and Replaced old brackets
7) Attached self-adhesive felt pads
8) Attached Drum Glides
9) Removed old felt seal
10) Glued new felt seal in place with 5-min epoxy
11) Allowed Epoxy to set and stop stinking
12) Re-attached front bulkhead
13) Re-attached remaining parts

Dryer works great, is quiet again, and no longer eats clothes!!!!!!
Read more...
Your Price
$47.12
  In Stock
Drying Rack
★★★★★
★★★★★
(5)
PartSelect Number PS346849
Manufacturer Part Number 3406839
This dryer drying rack is great for drying shoes and other items that cannot tumble dry. This dryer rack fits dryers that are 29 inches wide, have the letter "E" following the numbers in the model number, and whose dimples are four and a half inches apart in the back of the dryer drum.
Your Price
$61.37
  On Order
Front Glide Kit
★★★★★
★★★★★
(2)
PartSelect Number PS2003584
Manufacturer Part Number 12002126
This kit includes 2 glides (left and right), 2 pads with adhesive backing and 1 support brace.
Fixes these symptoms
Installation Instructions
Thomas from Oneonta, NY
Dryer made a loud noise and vibrated badly
First I made sure the unit was unplugged. I popped the top of the unit with a slotted screw driver, lifted the top up and rested it against the wall behind the dryer. I removed the two screws - one on each side in front on top of the dryer cabinet. Then I tipped back the front panel of the dryer slightly with the door of the dryer closed. I unclipped the door switch with a slotted screw driver and then lifted the entire front panel including the door off of the the two floor clips on bottom. I set the front panel aside. Next I lifted the large drum slightly to dislodge the rollers in back and slid the drum back slowly while sliding the thin belt back on the drum until the drum was out of the unit and the belt was detached and loose. Then I cleaned the unit thoroughly, vacuumed all lint and dirt and wiped down the outside of the large drum with mineral spirits to make sure it was totally clean and smooth. Then I removed the two rollers and the roller shafts at the back of the unit following the directions enclosed. My slip-ring pliers came in handy to remove the retaining rings on the roller shafts. I replaced the rollers and roller shafts and the supplied washers and spacers as per the instructions. I sprayed a little WD-40 on the surface of the rollers and it stopped all squeaking and vibration of the drum. Next I replaced the front drum pads and runners as per the instructions. I then slid the drum back in place taking care to slide the new belt back around the drum in the same position as the old belt. Now came the difficult part - laying on the floor and reaching under the drum I positioned the belt around the motor shaft and tension pulley. This must be done by "feel" and must be done correctly!! Follow the instructions on the positioning of the belt very carefully and make sure it is in the correct position on the drum, motor shaft, and tension pulley! Next, get up and rock the drum up and down slightly to make sure it has engaged the two rear rollers properly. Rotate the drum manually one or two turns to make sure the belt is in the correct position. Then replace the front door panel by dropping it onto the two clips at the base of the unit and taking care to replace the door switch in reverse order of taking it out. Then replace the two screws at the top front on each side of the unit to secure the front panel. Lower the top of the unit back in place, plug in the dryer, turn it on and enjoy the lack of noise you have created. Read more...
Your Price
$44.27
  In Stock
Tall Drum Baffle
PartSelect Number PS11743769
Manufacturer Part Number WP692490
Sold Individually - Appliance originally takes 2.
Installation Instructions
John from Santa Margarita, CA
Dryer belt worn out, rear seal worn replaced drum baffle
Unplugged unit and removed top and front of dryer. Removed drum and belt. noting how belt ran through the belt tension-er. Removed old felt seal from rear of drum. Replaced broken baffle, replaced rear seal. reinstalled belt. Put unit back together and test ran. Read more...
Your Price
$50.68
  On Order
Drum Front Bearing Ring
★★★★★
★★★★★
(2)
PartSelect Number PS11741470
Manufacturer Part Number WP3394509
This part mounts to the front of the drum.
Fixes these symptoms
Your Price
$61.89
  In Stock
Dryer Drum Baffle
PartSelect Number PS11741750
Manufacturer Part Number WP342847
The drum baffle lifts and tumbles the clothes inside the drum as the drum rotates during the drying cycle.
Your Price
$58.30
  On Order
Drum Baffle - Short
PartSelect Number PS11741670
Manufacturer Part Number WP3403636
This part moves the clothes around inside your dryer and helps to direct the flow of hot air during the drying cycle.
Your Price
$33.51
  In Stock
RACK-DRY
PartSelect Number PS11743761
Manufacturer Part Number WP689790

Related Parts