KitchenAid Dishwasher Motors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular KitchenAid Dishwasher Motors
Your Price
$69.25
In Stock
KitchenAid Dishwasher Motor
PartSelect Number PS5136127
Manufacturer Part Number W10537869
Also know as a diverter valve. This diverter motor is for dishwashers.
Diverter motor controls the flow of water to the spray arms.
Unplug the dishwasher and shut off the water supply before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Dennis from PORTAGE, MI
Diverter valve was leaking.
After shutting off electricity, lay dishwasher on it's side (use a towel to absorb any water) then just use nut driver to remove faulty valve.
Read more...
Your Price
$148.75
In Stock
KitchenAid Dishwasher Circulation Pump And Motor
PartSelect Number PS11757388
Manufacturer Part Number WPW10757217
The circulation pump and motor is located near the bottom of the dishwasher. The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle. Before you begin this repair, it is recommended that you pull your dishwasher out of the cabinet, so you can tip the dishwasher to one side and gain better access to the circulation pump and motor. Be sure to disconnect the power source and the water source to the dishwasher before you begin this repair. To complete this repair you will need a 1/4 inch nut driver and a 3/8 inch nut driver.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Steve from Inver Grove Heights, MN
Loud grinding noise from water pump
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.
Read more...
Your Price
$147.79
In Stock
KitchenAid Dishwasher Motor Pump
PartSelect Number PS11773089
Manufacturer Part Number W11032770
This OEM circulation pump and motor assembly fits select Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Magic Chef, and Kenmore dishwashers. It powers water flow through the spray arms, ensuring effective cleaning.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
christopher from MOSES LAKE, WA
wash pump stopped working
change out the old pump with new one actually quieter running pump awesome
Read more...
Your Price
$137.69
In Stock
KitchenAid Dishwasher Motor Pump
PartSelect Number PS11765780
Manufacturer Part Number W10894668
The pump motor delivers water to the spray arms to clean the dishes during the wash cycle.
Fixes these symptoms
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Terry from BELLINGHAM, WA
Dishes not coming clean
Replace motor-pump. All was as advertised plus the surprise of included outlet hose. I didn't have the tool to operate the clamp, it leaked, so I replaced it with a stainless worm gear type.
Read more...
Your Price
$156.43
In Stock
KitchenAid Dishwasher Motor
PartSelect Number PS11730993
Manufacturer Part Number W10843811
Ensure the peak performance of your Whirlpool dishwasher with this genuine OEM diverter motor. This vital component directs the water flow to the spray arms for efficient cleaning cycles. It's an essential replacement part when facing issues such as poor washing results or leakage around the diverter motor area. This motor is designed to be user-friendly, allowing for hassle-free installation. Remember to unplug the dishwasher and shut off the water supply before installing, and wear work gloves to protect your hands. Count on this trusted Whirlpool part to enhance the longevity and functionality of your appliance.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- See more...
Installation Instructions
Tim from Newberry, MI
Motor burned out
Shut off water and power,remove dishwasher, put dishwasher on its back, remove screws with Phillips screwdriver and reinstall
Read more...
Your Price
$85.21
In Stock
KitchenAid Dishwasher Diverter Motor W/wire Harness
PartSelect Number PS2328555
Manufacturer Part Number W10155344
NOTE: This part has been updated by the manufacture and the shaft seal is now incorporated into the sump housing. The seal for diverter motor shaft only available with the pump sump housing.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- See more...
Installation Instructions
John from Springfield, OH
Water leaking underneath dishwasher
The leak was dripping from the diverter motor. After removing dishwasher the diverter motor was found to be corroded. The shaft grommet looked good. A new diverter motor was installed and dishwasher connected. After running it awhile the leak reappeared. It seemed the only possible thing left was the shaft grommet. Of course the grommet comes as part of the belly assembly. After searching for a better and cheaper solution I ordered a Whirlpool WPW10195677 grommet and it solved the leak.
Read more...
Your Price
$71.23
In Stock
KitchenAid Dishwasher Vent Fan Motor
PartSelect Number PS11755275
Manufacturer Part Number WPW10469575
Introducing a genuine OEM Whirlpool part - the Vent Fan Motor Door Vent Assembly. This high-quality component, designed for ultimate functionality and durability, works with selected models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef. This Vent Assembly is specifically used for dishwashers, where it plays an essential role in releasing moisture during the drying cycle. When it comes to installation, remember to unplug the dishwasher or switch off the house circuit breaker for safety. Don't forget to wear work gloves to protect your hands during this process. Enjoy enhanced performance and longevity with this premium Whirlpool appliance part.
Fixes these symptoms
- Leaking
- See more...
Your Price
$166.95
In Stock
KitchenAid Dishwasher Motor Pump
PartSelect Number PS11766745
Manufacturer Part Number W10907617
The pump motor delivers water to the spray arms to clean the dishes during the wash cycle.
Fixes these symptoms
- Not cleaning dishes properly
- See more...
Your Price
$155.47
In Stock
KitchenAid Dishwasher Circulation Pump And Motor Assembly
PREPARE FOR REMOVAL: Unscrew / Remove kickplate. Disconnected water connect just behind the kickplate. Be ready with a couple of dishtowels. Pull the door down and remove any screws that go into the under part of your counter top. Jack the front legs screw down.
REMOVE: Gently pull the Dishwasher from under counter. Push the insulation flat against the side of the dishwasher about every six inches that you pull the dishwasher out to prevent it from snaggin on the cabinet face edges. Remove the baskets and spray arms. Careful not to damage the heating element.
NOTE: Here I noticed that the guy who installed the dishwasher kinked the copper line limiting the water into to my dishwasher. So my circulation pump/motor was probably running dry. I replaced with a flex type "dishwasher" hose that will easily coil up behind / underneath without kinking when I push back in. DO THE REPAIR RIGHT - DO IT YOURSELF!
REPAIR: I gently laid the dishwasher on it's side (cardboard underneath). I disconnected the power - 2 wires. Then, I only disconnect one wire harness, the sump tubing and the I thought I'd better remove the impeller that the sump tubing was connected to (it was only attached with one screw). Remove the 3 plastic clips around the pump/motor. Carefully push the pump into the dishwasher. DO NOT LET THE PUMP FALL AS IT MAY DAMAGE THE HEATING ELEMENT IN THE DISHWASHER! Push the new pump/motor in place until the seal is at least flush with the bottom. I used the back of a wood spoon. Don't pull on any part of the motor from the bottom or you'll break the thin aluminum casting. Just inserting the plastic clips back in place will pull the seal flush with the bottom again.
I was lucky. I simply removed the motor/pump, replaced it with the new motor/pump, and put everything back together in reverse. I put a little bit of silicone grease on the o-ring of the temperature probe. I happened to have some silicone grease because I also have a pool.
Done. It cost me $220 Vs. $550 quoted by Sears. That doesn't count the extra Sears would have charged my for repairing the kinked copper line. And you know they would've kinked it again. That only cost me $20 more and the flexible line couldn't have been easier to install. I could have done the whole thing for less but I opted to replace the pump/ motor together.
Getting it all done right, no leaks, no kinked line, keeping the dishwasher that matches the other appliances (VS. replacing it at $550 repair price), all less than 1/2 the price of a quoted repair - PRICELESS. - THANK YOU PART SELECT. DISCLAIMER: I have no affiliation with Part Select. Read more...
PartSelect Number PS11699805
Manufacturer Part Number W10782773
*** This part no longer includes the Chopper Assembly as per the Manufacturer ***
The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Geoffrey from Indianapolis, IN
Dishwasher was not cleaning dishes.
SAFTY: Turn water off. Flip the circuit breaker.PREPARE FOR REMOVAL: Unscrew / Remove kickplate. Disconnected water connect just behind the kickplate. Be ready with a couple of dishtowels. Pull the door down and remove any screws that go into the under part of your counter top. Jack the front legs screw down.
REMOVE: Gently pull the Dishwasher from under counter. Push the insulation flat against the side of the dishwasher about every six inches that you pull the dishwasher out to prevent it from snaggin on the cabinet face edges. Remove the baskets and spray arms. Careful not to damage the heating element.
NOTE: Here I noticed that the guy who installed the dishwasher kinked the copper line limiting the water into to my dishwasher. So my circulation pump/motor was probably running dry. I replaced with a flex type "dishwasher" hose that will easily coil up behind / underneath without kinking when I push back in. DO THE REPAIR RIGHT - DO IT YOURSELF!
REPAIR: I gently laid the dishwasher on it's side (cardboard underneath). I disconnected the power - 2 wires. Then, I only disconnect one wire harness, the sump tubing and the I thought I'd better remove the impeller that the sump tubing was connected to (it was only attached with one screw). Remove the 3 plastic clips around the pump/motor. Carefully push the pump into the dishwasher. DO NOT LET THE PUMP FALL AS IT MAY DAMAGE THE HEATING ELEMENT IN THE DISHWASHER! Push the new pump/motor in place until the seal is at least flush with the bottom. I used the back of a wood spoon. Don't pull on any part of the motor from the bottom or you'll break the thin aluminum casting. Just inserting the plastic clips back in place will pull the seal flush with the bottom again.
I was lucky. I simply removed the motor/pump, replaced it with the new motor/pump, and put everything back together in reverse. I put a little bit of silicone grease on the o-ring of the temperature probe. I happened to have some silicone grease because I also have a pool.
Done. It cost me $220 Vs. $550 quoted by Sears. That doesn't count the extra Sears would have charged my for repairing the kinked copper line. And you know they would've kinked it again. That only cost me $20 more and the flexible line couldn't have been easier to install. I could have done the whole thing for less but I opted to replace the pump/ motor together.
Getting it all done right, no leaks, no kinked line, keeping the dishwasher that matches the other appliances (VS. replacing it at $550 repair price), all less than 1/2 the price of a quoted repair - PRICELESS. - THANK YOU PART SELECT. DISCLAIMER: I have no affiliation with Part Select. Read more...
Your Price
$140.95
In Stock
KitchenAid Dishwasher Pump & Motor
PartSelect Number PS11703497
Manufacturer Part Number W10805015
Introducing the Whirlpool Dishwasher Pump and Motor Assembly, a genuine OEM product expertly designed to enhance your dishwasher?s performance. This crucial appliance component works seamlessly with select models of Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dishwashers. Crafted to perfection, this pump and motor assembly play a vital role in pumping water through the spray arms during your dishwashing cycle. Ensure the house circuit breaker for your dishwasher is switched off before initiating the installation process. To protect your hands and ensure safety, it is advisable to wear work gloves during the installation. For optimal results and compatibility, please ensure the part number aligns with your dishwasher model prior to purchase.
Related KitchenAid Dishwasher Parts
- All KitchenAid Dishwasher parts
- KitchenAid Dishwasher Brackets and Flanges
- KitchenAid Dishwasher Caps and Lids
- KitchenAid Dishwasher Circuit Boards and Touch Pads
- KitchenAid Dishwasher Dishracks
- KitchenAid Dishwasher Dispensers
- KitchenAid Dishwasher Doors
- KitchenAid Dishwasher Ducts and Vents
- KitchenAid Dishwasher Filters
- KitchenAid Dishwasher Handles
- KitchenAid Dishwasher Hardware
- KitchenAid Dishwasher Hoses and Tubes
- KitchenAid Dishwasher Latches
- KitchenAid Dishwasher Panels
- KitchenAid Dishwasher Pumps
- KitchenAid Dishwasher Racks
- KitchenAid Dishwasher Seals and Gaskets
- KitchenAid Dishwasher Spray Arms
- KitchenAid Dishwasher Springs and Shock Absorbers
- KitchenAid Dishwasher Switches
- KitchenAid Dishwasher Wheels and Rollers
- KitchenAid Dishwasher Wire Plugs and Connectors