Kenmore Washer Wire Plugs and Connectors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Kenmore Washer Wire Plugs and Connectors
Your Price
$23.68
In Stock
Kenmore Washer Drive Block - 2 5/16 Inch High
PartSelect Number PS11741977
Manufacturer Part Number WP389140
This part is for large capacity belt drive and direct drive appliances.
Fixes these symptoms
- Leaking
- Spins slowly
- Will not agitate
- See more...
Installation Instructions
Dexter from Milwaukie, OR
Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go.
Read more...
Your Price
$65.90
In Stock
Your Price
$17.83
In Stock
Your Price
$103.94
In Stock
Your Price
$43.67
In Stock
Your Price
$70.56
In Stock
Your Price
$43.67
In Stock
Your Price
$22.40
On Order
Your Price
$85.94
In Stock
Your Price
$16.52
On Order
Kenmore Washer Connector Assembly
PartSelect Number PS7786632
Manufacturer Part Number ACJ73350401
Installation Instructions
Richard from RED LION, PA
Water leaking into drum
Figured out how to remove the top door and the top panel that covered the solenoid bank. That was the hardest part. Swapping out the solenoid bank and the connector was easy. No more water leaking.
Read more...
Related Kenmore Washer Parts
- All Kenmore Washer parts
- Kenmore Washer Agitators
- Kenmore Washer Bearings
- Kenmore Washer Belts
- Kenmore Washer Brackets and Flanges
- Kenmore Washer Caps and Lids
- Kenmore Washer Circuit Boards and Touch Pads
- Kenmore Washer Dispensers
- Kenmore Washer Doors
- Kenmore Washer Drawers and Glides
- Kenmore Washer Drums and Tubs
- Kenmore Washer Filters
- Kenmore Washer Handles
- Kenmore Washer Hardware
- Kenmore Washer Hinges
- Kenmore Washer Hoses and Tubes
- Kenmore Washer Knobs
- Kenmore Washer Latches
- Kenmore Washer Legs and Feet
- Kenmore Washer Motors
- Kenmore Washer Panels
- Kenmore Washer Power Cords
- Kenmore Washer Pulleys
- Kenmore Washer Pumps
- Kenmore Washer Seals and Gaskets
- Kenmore Washer Springs and Shock Absorbers
- Kenmore Washer Switches
- Kenmore Washer Timers
- Kenmore Washer Transmissions and Clutches
- Kenmore Washer Valves