Kenmore Refrigerator Insulations

Find your part

Enter your model number or a part number and click "Search"
Need help finding your model number?
Kenmore Appliance Parts
Shop By Part Type

Popular Kenmore Refrigerator Insulations

Your Price
$38.58
  In Stock
Door Insulation
PartSelect Number PS1526428
Manufacturer Part Number 241688601
Your Price
$29.45
  In Stock
Tub Sound Shield - Insulation
★★★★★
★★★★★
(2)
PartSelect Number PS12070612
Manufacturer Part Number W11086533
Your Price
$9.08
  In Stock
Spacer
★★★★★
★★★★★
(1)
PartSelect Number PS11743296
Manufacturer Part Number WP625834
Sold individually.
Fixes these symptoms
Installation Instructions
Raymond from KALAMAZOO, MI
The control bracket which holds the micro switches broken on the water side.
Removed the front cover, not easy, I was worried it was going to break but it did pop off. Be sure to locate the two notches on the bottom so your pulling in the correct location. Unplugged the wire harness from the front cover and control panel, there is a locking tab on one side that must be released to unplug. Removed two screws that hold the control bracket, slide it out and remove the micro switches and lamp holder. Unplug the wires from the micro switches, it is easier to do when they are not in the control bracket. Attach the wires to the new micro switches, I replaced both since it was apart. Install the spacers for the switches and then slide on each switch. Make sure they are locked into the notch on the two support pins for each switch. Snap in the lamp holder and check the wiring routes so nothing is pinched. Attach the control bracket and plug the front panel into the control bracket plug and then test the water and ice. If they both work you've done a good job. The new control panel has a place to slide the wiring connection in so it stays in place. Do it now and snap the cover back on. I had to hit the bottom corners pretty hard to get it to snap in but once it is in place it is solid. It took about 30 minutes but I had taken this apart before when I discovered the holders for the water micro switch were broken so that made it much easier the second time around. The new bracket and holders seem to be made better. The new drip tray is also much better and fits much better two. Good luck, don't be in a hurry. Read more...
Your Price
$23.04
  On Order
Insulation
★★★★★
★★★★★
(1)
PartSelect Number PS1632252
Manufacturer Part Number 67003796
Fiber Acoustic.
Your Price
$18.20
  In Stock
Styrofoam Duct Insert
PartSelect Number PS299044
Manufacturer Part Number WR2X8462
Installation Instructions
Vincent from Burlington, MA
Frost build-up in freezer and temperature too high
Cleared drain tube and replaced styrofoam duct insert. Had to remove 3 panels inside the freezer. Warmed up the freezer to melt all the ice and inserted a steel cable into the drain tube to be sure it was clear. The styrofoam insert simply sits in place (no screws or glue). Easy to replace. Read more...
Your Price
$12.94
  In Stock
INSULATION
PartSelect Number PS3495507
Manufacturer Part Number 242096001
Your Price
$25.02
  On Order
Insert Kit
PartSelect Number PS371967
Manufacturer Part Number 4388450
This kit comes with two pieces.
Fixes these symptoms
Your Price
$5.71
  In Stock
BLOCK- FIL
PartSelect Number PS11738614
Manufacturer Part Number WP12777701
Your Price
$8.67
  Special Order
INSULATION
PartSelect Number PS11775655
Manufacturer Part Number 5304508046
Your Price
$38.93
  Special Order
Water Filter Cover Insulation - White
PartSelect Number PS430416
Manufacturer Part Number 240394102
Fixes these symptoms
Installation Instructions
Carmen from Haverhill, MA
Filter cup was broken
removed the 2 screws then the housing. Then i removed the 2 hoses that are connected to the filter cup.Replaced it with the new one then i connected the water filter . Read more...

Related Parts

Back to Top