Kenmore Refrigerator Door Shelves
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Kenmore Refrigerator Door Shelves
Your Price
$10.62
In Stock
Kenmore Refrigerator Door Shelf Retainer Bar End Cap (right Side)
PartSelect Number PS429668
Manufacturer Part Number 240311502
This replacement bar end cap can be used for a shelf in your freezer. The end cap is 4.25 inches long and 2.4 inches wide. You may need a flat blade screwdriver in order to pop out the existing end cap. Slide the new cap in place, making sure the locking tab is secure, and replace the bar.
Installation Instructions
Nancy from Pleasant Prairie, WI
tenants had broken door brackets in fridge
cut brackets to size and snapped them into place with the caps purchased. I will continue to use PartSelect for all my appliance repair needs. Not only did I receive my order within 2 days but the cost was over half of what I have been paying for the local parts store to order for me. Thank you PartsSelect.
Read more...
Your Price
$10.62
In Stock
Kenmore Refrigerator Door Shelf Retainer Bar End Cap (left Side)
PartSelect Number PS429667
Manufacturer Part Number 240311501
This is a replacement end cap for your freezer or refrigerator shelf retainer bar. You will need a flat blade screwdriver to complete this repair. To replace this part, remove the retainer bar by popping the end caps out of place. Use the screwdriver to pop out the individual end cap you are replacing. Secure the new one in place with the locking tabs and re-insert the retainer bar.
Installation Instructions
Nancy from Pleasant Prairie, WI
tenants had broken door brackets in fridge
cut brackets to size and snapped them into place with the caps purchased. I will continue to use PartSelect for all my appliance repair needs. Not only did I receive my order within 2 days but the cost was over half of what I have been paying for the local parts store to order for me. Thank you PartsSelect.
Read more...
Your Price
$7.71
In Stock
Kenmore Refrigerator Door Shelf End Cap (left Or Right Side)
When the defrost timer is advanced to the defrost cycle the switch closes sending power to the defrost thermostat. If the temperature is low enough, the defrost thermostat switch will close and sends power to the heating elements. When the temperature rises high enough about 55 degrees the switch at the thermostat will open and the heating elements will turn off (not allowing the freezer temperature to get too high, just enough to defrost the coil). The refrigerator will turn back on when the timer advances. The defrost timer will defrost every 8-12 hours. Read more...
PartSelect Number PS422444
Manufacturer Part Number 215267701
This end cap can be used for the right or left side of the refrigerator door shelf or the freezer door shelf. It is white in color, made of plastic material and measures about 2 inches high by 3 inches deep. This might need to be replaced if it has broken or worn over time. This repair requires no tools. You will need to open your fridge, pull upwards on the existing end cap, and pull outwards. There is a locking tab on either end so it does not matter if the top or bottom comes out first. Slide the new end cap onto the rail and it is installed.
Installation Instructions
David from Fleetwood, PA
Freezer / refrigerator warm (not defrosting)
I checked the defrost timer (bottom front of the freezer / outside). I advanced it to send it into the defrost cycle. The heating elements in the freezer (behind the panel) did not heat up. I cut the wires going to the defrost thermostat. Turned the power back on, made sure the defrost timer was still in the defrost cycle and checked the voltage at the wires to the defrost thermostat (before the heating elements). There was power / voltage there. I jumped out / bypassed the defrost thermostat turned the power back on and the heating elements came on. The problem was the defrost thermostat. So I replaced it with a new one from PartSelect.com. How it works...When the defrost timer is advanced to the defrost cycle the switch closes sending power to the defrost thermostat. If the temperature is low enough, the defrost thermostat switch will close and sends power to the heating elements. When the temperature rises high enough about 55 degrees the switch at the thermostat will open and the heating elements will turn off (not allowing the freezer temperature to get too high, just enough to defrost the coil). The refrigerator will turn back on when the timer advances. The defrost timer will defrost every 8-12 hours. Read more...
Your Price
$50.30
In Stock
Kenmore Refrigerator Door Bin (clear)
PartSelect was helpful to acquire the parts. Read more...
PartSelect Number PS976767
Manufacturer Part Number 241511701
Sold individually.
Installation Instructions
Mark from Shorewood, MN
Refrigerator didn't come with racks
The repair was very easy - the door and can racks just click into place. No tools were needed.PartSelect was helpful to acquire the parts. Read more...
Your Price
$9.65
In Stock
Kenmore Refrigerator Door Shelf End Cap (left Or Right Side)
The refrigerator and freezer door gaskets were the first step. They were easy to swap out. You just need to empty the door of all food items, then pull back the old gasket to see the screws. There are alot of them. You should leave 2 loosened screws on each side of the refrigerator door to hold the panel in place while you work and remove the rest. Then you can remove the old gasket and slide the new one into place. Make sure as you tighten the screws and replace the ones you removed, the new gasket fits into the door panel groove securely and is in place as you tighen the screws. Make sure it is in place all the way around the door as you work. You repeat the procedure for the freezer using only one loosened screw on each side to keep the interior panel in place while you work. It takes some time due to the number of screws, but the work is pretty easy. I never even broke a nail.
The end caps for the shelf bars just snap into place just as the old ones can be snapped out with a bit of pressure. They do not have to be wrestled and you need to work carefully so that you do not break them. (I ordered an extra just in case, but I didn't need it. I will have it in case I need it in the future)
My electric bill dropped from $450 to $110 a month with all the improvements I made. Thank you Part Select for taking the fear of screwing it up, out of the repair process and making it manageable. I can afford my electric bill now. Thanks for your help. Read more...
PartSelect Number PS422925
Manufacturer Part Number 215473602
The door shelf end cap, or door bin support, secures the rack in a refrigerator or freezer door. Note that this fits on either the left or right hand side. If the end caps of your refrigerator or freezer are broken or cracked, or if your food retainer bar is not staying in place, then replacing the door support can solve this problem. No tools are needed for this repair project. To repair, first remove the end cap by pushing upward or downwards to slide it out the end of the rail. Next, replace with new end cap and line it up to clip it back onto the rail. It comes in white and measures about two inches high. Remember to wear gloves for safety.
Installation Instructions
Lynn from New York,, NY
My electric bill was super high. $450 for 1 month for a 1bdrm apt in NY city
I took a look at the web site where I purchased the parts, then I took a look at the paper enclosed with the order. Thankfully, I have a battery operated screw driver since there are so many screws. There are plenty of screws in my refrigerator and freezer doors. I thought that since my old door gaskets were all chewed up looking, if I changed them, the 10 year old air conditioners and the old fashioned light bulbs to instant on energy saver light bulbs, the electric bill would become more manageable. The refrigerator and freezer door gaskets were the first step. They were easy to swap out. You just need to empty the door of all food items, then pull back the old gasket to see the screws. There are alot of them. You should leave 2 loosened screws on each side of the refrigerator door to hold the panel in place while you work and remove the rest. Then you can remove the old gasket and slide the new one into place. Make sure as you tighten the screws and replace the ones you removed, the new gasket fits into the door panel groove securely and is in place as you tighen the screws. Make sure it is in place all the way around the door as you work. You repeat the procedure for the freezer using only one loosened screw on each side to keep the interior panel in place while you work. It takes some time due to the number of screws, but the work is pretty easy. I never even broke a nail.
The end caps for the shelf bars just snap into place just as the old ones can be snapped out with a bit of pressure. They do not have to be wrestled and you need to work carefully so that you do not break them. (I ordered an extra just in case, but I didn't need it. I will have it in case I need it in the future)
My electric bill dropped from $450 to $110 a month with all the improvements I made. Thank you Part Select for taking the fear of screwing it up, out of the repair process and making it manageable. I can afford my electric bill now. Thanks for your help. Read more...
Your Price
$10.62
In Stock
Kenmore Refrigerator Door Shelf Retainer Bar End Cap
PartSelect Number PS11738927
Manufacturer Part Number WP2156003
The door shelf retainer bar end cap connects to the retainer bar on your refrigerator’s door shelf, and attaches it to the refrigerator door. If your shelf retainer bar has become disconnected, a damaged end cap could be the cause. To remove the end cap, first unhook the release tab on both ends of the retainer bar. Slide out the bar and the end caps, and slide out the defective cap. Now, simply replace the end cap and snap the bar with end caps back in place on the refrigerator door. This part is made of white plastic and is sold individually.
Installation Instructions
Stefanie from Sycamore, IL
broken end cap
Simple....snapped it right on...the important thing is that we ordered it for a reasonable price, and it arrived quickly...within 3 days. thanks!!!
Read more...
Your Price
$114.86
In Stock
Kenmore Refrigerator Door Bin Shelf
PartSelect Number PS7794183
Manufacturer Part Number MAN62570401
This door basket, commonly referred to as a door shelf, is a genuine OEM replacement part designed for use in LG refrigerators. It is a translucent, plastic shelf that is positioned on the inside of the fridge door. It provides a convenient space to store your food items and containers. The door shelf should be replaced if it is cracked, warped, or can no longer remain attached to the door. A faulty door shelf may cause your food items to fall and break and it may damage the interior of the fridge. Each door shelf is sold separately. You do not need fasteners to mount the shelf.
Your Price
$109.12
In Stock
Kenmore Refrigerator Door Basket
PartSelect Number PS10066452
Manufacturer Part Number MAN62749601
This door bin, also known as a door basket, is an authentic manufacturer replacement part made for your LG fridge. It is made of clear plastic and it fits on to mounting brackets inside of the door fridge. The door bin provides storage for various food items such as condiments, bottles, and jars. If door bin cracks or breaks you will need to replace it to avoid falling food items and potential damage to the door frame.
Installation Instructions
Evangelina from GETTYSBURG, PA
Very simple replacement
it was as easy as taking a basket door off and replacing it with a new one and taking a deli drawer out and replacing it with a new one. The most difficult process was ordering because I didn’t have product numbers so I had to go buy these pictures and some were difficult to understand.
Read more...
Your Price
$6.74
In Stock
Kenmore Refrigerator Door Shelf Retainer Bar End Cap (right Side)
If the end cap doesn't lock into place when you slide it into the metal retainer bar, you may need to bend the bar (gently) to get the notches around the plastic clips. You don't need a lot of force to do this since all you want is to lock the end cap in place. Read more...
PartSelect Number PS429834
Manufacturer Part Number 240331502
This part is the replacement door shelf retainer bar end cap for your refrigerator. It is made of white plastic and measures approximately 3 inches by 4 inches. The door shelf retainer bar end cap is found at the end of the shelf retainer bar, which it connects to the refrigerator door. The main reason to change out the shelf retainer bar is if it is broken or missing, and you can’t connect the retainer bar to the refrigerator door. This part is for the right side of the end cap only. The left side end cap is sold separately. This is an authentic OEM part sourced directly from the manufacturer.
Installation Instructions
George from Worcester, MA
Door shelf bar broke
This was a really simple repair. The hardest part was getting the broken piece of the plastic end cap out of the metal retainer bar. I had to use a small screwdriver to gently pry it out of the two notches in the retainer bar. Then I just slipped on the new part, and snapped the whole retainer bar into the fridge door and that was it. If the end cap doesn't lock into place when you slide it into the metal retainer bar, you may need to bend the bar (gently) to get the notches around the plastic clips. You don't need a lot of force to do this since all you want is to lock the end cap in place. Read more...
Your Price
$7.71
In Stock
Kenmore Refrigerator Door Shelf Retainer Bar End Cap (left Side)
PartSelect Number PS429833
Manufacturer Part Number 240331501
This part is the middle retainer bar end cap for the left side of your refrigerator door. It is designed to hold the retainer bar in place, and prevent food and beverage items from slipping out when the door is opened. It is made of white plastic, and is sold individually. This is a genuine OEM part, which comes directly from the manufacturer.
Installation Instructions
Erik from Portland, OR
Broken shelves in the fridge
Just had to pop the old pieces out, assemble the new ones, and pop them in. Very easy. Anyone can do it.
Read more...
Related Kenmore Refrigerator Parts
- All Kenmore Refrigerator parts
- Kenmore Refrigerator Brackets and Flanges
- Kenmore Refrigerator Caps and Lids
- Kenmore Refrigerator Circuit Boards and Touch Pads
- Kenmore Refrigerator Compressors
- Kenmore Refrigerator Deflectors and Chutes
- Kenmore Refrigerator Dispensers
- Kenmore Refrigerator Doors
- Kenmore Refrigerator Drawers and Glides
- Kenmore Refrigerator Drip Bowls
- Kenmore Refrigerator Ducts and Vents
- Kenmore Refrigerator Electronics
- Kenmore Refrigerator Elements and Burners
- Kenmore Refrigerator Fans and Blowers
- Kenmore Refrigerator Filters
- Kenmore Refrigerator Grates
- Kenmore Refrigerator Grilles and Kickplates
- Kenmore Refrigerator Handles
- Kenmore Refrigerator Hardware
- Kenmore Refrigerator Hinges
- Kenmore Refrigerator Hoses and Tubes
- Kenmore Refrigerator Ice Makers
- Kenmore Refrigerator Insulations
- Kenmore Refrigerator Insulations
- Kenmore Refrigerator Knobs
- Kenmore Refrigerator Latches
- Kenmore Refrigerator Lights and Bulbs
- Kenmore Refrigerator Motors
- Kenmore Refrigerator Panels
- Kenmore Refrigerator Power Cords
- Kenmore Refrigerator Seals and Gaskets
- Kenmore Refrigerator Sensors
- Kenmore Refrigerator Springs and Shock Absorbers
- Kenmore Refrigerator Switches
- Kenmore Refrigerator Tanks and Containers
- Kenmore Refrigerator Thermostats
- Kenmore Refrigerator Timers
- Kenmore Refrigerator Trays and Shelves
- Kenmore Refrigerator Trims
- Kenmore Refrigerator Trims
- Kenmore Refrigerator Valves
- Kenmore Refrigerator Wheels and Rollers
- Kenmore Refrigerator Wire Plugs and Connectors