Kenmore Dishwasher Pumps
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Kenmore Dishwasher Pumps
Your Price
$67.27
In Stock
Kenmore Dishwasher Drain Pump
PartSelect Number PS16744934
Manufacturer Part Number W11612326
This circulation pump is a genuine OEM replacement part designed for use in dishwashers. It is responsible for circulating water throughout the dishwasher during the wash and rinse cycles. The circulation pump draws water from the dishwasher tub, pressurizes it, and then distributes it to the spray arms, which spray the water onto the dishes to remove food particles and debris. The circulation pump may fail due to several reasons such as an electrical fault, a blockage in the pump impeller, motor failure, or physical damage. A faulty pump will result in water leakages, unusually loud noises during use, reduced water circulation, and poor cleaning performance.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Samoil from COOPER CITY, FL
The dish washer wasn’t cleaning dishes
The circulation pump is a super easy fix and the installation video parts select has on its website is accurate. I felt the most difficult part of the repair was removing the dishwasher from the kitchen counter to make the repairs. After you get the dishwasher out, you pretty much just pop the old pump out with your hands and a flat head screwdriver. (The supplied video is spot on ) Installing the new pump will require a pinch plier or a hose clamp. I chose a new hose clamp as it is cheaper and I would never use the pinch pliers after this job.
Read more...
Your Price
$59.35
In Stock
Kenmore Dishwasher Drain Pump 120v 60hz
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...
PartSelect Number PS11753379
Manufacturer Part Number WPW10348269
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Andrew from Alexandria, VA
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...
Your Price
$95.01
In Stock
Kenmore Dishwasher Drain Pump -120v 60hz
Under Dishwasher:
Removed water feed connection.
On top of Dishwasher:
Removed screws anchoring it to cabinet.
Pulled dishwasher out and flipped down so it’s resting on the front.
Removed drain hose on drain pump.
Removed 3 torx screws on pump, greased o-ring on new pump and reinstalled doing the reverse of these instructions.
Took 1 hour and now it works great! Read more...
PartSelect Number PS8689824
Manufacturer Part Number A00126401
This is a drain pump assembly for various compatible models of dishwashers, that is responsible for draining the water from the dishwasher after every cycle. This drain pump assembly is made of plastic and fits within the sump assembly, which controls the flow of water into the drain. This drain pump assembly is a genuine OEM part and is made of a high-quality plastic but is sold as an individual component without any other parts, like its drain pump check ball which works within the pump to prevent water from backwashing into the pump, as well as the drain pump cover. If you notice your dishwasher is not draining or has a lot of water buildup at the bottom of the sump assembly, this filter may be damaged, clogged or broken, and in need of a replacement. To replace this pump assembly, you will only need a Philips-head screwdriver, but should start by removing your dishwasher racks. Then, pull up on the lower spray arm, and drain trap to remove them. Next, rotate the spray arm support and pull that up to remove it, at which point you can remove the base and filter for the drain pump. With those out, you can use your Philips-head screwdriver to disconnect and remove the cover and drain pump assembly. With the pump removed, you can inspect it or install the new drain pump assembly, with the same hardware as before. Then it is as simple as reassembling the rest of your dishwasher, ensuring each connection point is fastened tightly.
Fixes these symptoms
- Leaking
- Noisy
- Not draining
- See more...
Installation Instructions
William from FRANKLIN, TN
Dishwasher stopped draining
Under sink: Disconnected drain hose to garbage disposal, shutoff water feed, unplugged power.Under Dishwasher:
Removed water feed connection.
On top of Dishwasher:
Removed screws anchoring it to cabinet.
Pulled dishwasher out and flipped down so it’s resting on the front.
Removed drain hose on drain pump.
Removed 3 torx screws on pump, greased o-ring on new pump and reinstalled doing the reverse of these instructions.
Took 1 hour and now it works great! Read more...
Your Price
$59.35
In Stock
Kenmore Dishwasher Drain Pump
Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn and push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front. Read more...
PartSelect Number PS11738151
Manufacturer Part Number W10876537
This drain pump is for dishwashers.
Drain pump removes the water from the dishwasher tub during the drain phase of the dishwashing cycle.
Unplug the dishwasher and shut off the water supply before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
- Leaking
- Not draining
- See more...
Installation Instructions
Kelli from BURLINGTON, MA
Dish washer would not drain properly
Shut off breaker. Took off front skirt of dishwasher . Used pliers to loosen the pressure clamp on drain pump , have towel handy as there will be some water. Turn pump to left as you push in on the clip on side of drain pump. It will come out. Remove wire plug from old pump and plug into new pump than insert new pump and turn and push in till it clicks. Use pliers to pinch hose clamp and push hose onto pump release hose clamp. Turn breaker on. Run a cycle and make sure all is tight before putting skirt on front. Read more...
Your Price
$33.95
In Stock
Kenmore Dishwasher Chopper Assembly
PartSelect Number PS1734917
Manufacturer Part Number W10083957
This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clogging the pump. You may need to replace this part if your dishes are not being cleaned properly, your appliance is particularly noisy, or you are noticing draining problems. The tools you will need to make this repair include a number 20 and a number 15 torque screwdriver, a small flat blade screwdriver, and a pair of needle nose pliers.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Steve from Killeen, TX
Not cleaning top tier,all dishes not getting clean
Disassembled inside bottom section of dishwasher found broken chopper part,removed and replaced with new part,only hard part was holding spring compressed when putting in new part,needed needlenose and thin screwdriver.Thank You for your great website and help
Read more...
Your Price
$67.27
In Stock
Kenmore Dishwasher Circulation Pump
PartSelect Number PS16744935
Manufacturer Part Number W11612327
The pump motor delivers water to the spray arms to clean the dishes during the wash cycle.
Fixes these symptoms
- Not cleaning dishes properly
- Will not fill with water
- See more...
Your Price
$59.19
In Stock
Kenmore Dishwasher Drain Pump - 55hz
It took me 20 minutes from start to finish Read more...
PartSelect Number PS8727352
Manufacturer Part Number 00611332
The pump ejects the water from the dishwasher through the drain hose.
Fixes these symptoms
- Noisy
- Not draining
- Will Not Start
- See more...
Installation Instructions
Steven from STATEN ISLAND, NY
Error code E24
when you receive the drain pump and you are ready to install make sure you put VASELINE around the rubber Gromit that will make putting the drain pump in very easy, also to give yourself more space to remove and install the pump remove the front door panel.It took me 20 minutes from start to finish Read more...
Your Price
$55.39
In Stock
Kenmore Dishwasher Drain Pump
PartSelect Number PS11756031
Manufacturer Part Number WPW10531320
This drain pump is an authentic OEM replacement part for models of dishwasher. It is responsible for removing wastewater from the dishwasher during the drainage cycle. It is located at the bottom of the dishwasher and can be accessed by removing the lower access panel or by tipping the dishwasher on to its rear side. When activated, the drain pump pushes the wastewater through the drain hose and into the household plumbing system or garbage disposal. If the drain pump malfunctions or becomes clogged, it can lead to drainage issues, resulting in water pooling at the bottom of the dishwasher, foul odors and potentially resulting in incomplete cleaning of dishes.
Fixes these symptoms
- Leaking
- Noisy
- Not draining
- See more...
Installation Instructions
Douglas from SAINT JOHN, IN
Dishwasher was making a moaning sound when draining.
Unplug dishwasher. Remove lower front accessible panel. Disconnect wires to the drain pump. Rotate pump to unlock and remove. Apply plumbers grease to rubber seal and install new pump. Connect wires. Plug in dishwasher and run rinse cycle to check for no water leak. If all okay replace access panel. Done.
Read more...
Your Price
$81.95
In Stock
Kenmore Dishwasher Drain Pump
PartSelect Number PS11706890
Manufacturer Part Number ABQ73503004
This drain pump assembly is a genuine OEM replacement part for your dishwasher. In order to complete this repair you will need a Phillips screwdriver, pliers, and a socket. You will need to pull the dishwasher out from the cabinet and lay it on its back in order to access through the bottom and replace the drain pump.
Fixes these symptoms
- Not draining
- See more...
Installation Instructions
Patrick from CHANDLER, AZ
Water not draining, causing "0E" number to appear and initiatate dishwasher shutdown.
According to your site, the part(s), to consider, to resolve the problem were: 1.Motor Assembly DC Pump, OR 2.Drain Pump. I simply selected the drain pump because it was cheaper and because it was making a clicking noise. (The only significant noise that this dishwasher was making) To be safe, I unplugged the unit and turned off the water, under the sink. I removed the kick plate and I unscrewed the anchor clips from under the counter and carefully pulled the unit out. I then opened the dishwasher and removed the lower rack. To minimize water clean-up, I took a rag and soaked up the standing water in the bottom until it was nearly dry. I then tipped the dishwasher on it's left side, knowing where the location of the drain pump (front, right), would be in an easier location for me to work. I first unplugged the pumps wiring. Then, with pliers, I was able to disconnect the clips on the short, rubber hoses that hold the pump in alignment.(Use caution: If reusing the same rubber hose(s) on the new pump, it will be easier if you put them on in the same direction as they were take off) Then I removed the rubber supports off their hooks, that allow the pump to hang from the bottom of the dishwasher. Once the rubber hoses are re-connected on the new pump and placed on to it's former proper alignment, you can re-attach the rubber supports to their hooks. And last, but not least, remember to plug the new pump's wires back in place. Carefully stand up dishwasher and push it slowly back into place. I plugged in the unit and turned on the water. Before I screwed the unit back to the counter and kick plate back on the front, I ran a load and watched for leaks beneath the new pumps area. No leaks. "Easy, Peasy".
Read more...
Your Price
$136.87
In Stock
Kenmore Dishwasher Drain Pump
PartSelect Number PS8729769
Manufacturer Part Number 00642239
The drain pump ejects the water from the dishwasher.
Fixes these symptoms
- Noisy
- Not draining
- See more...
Installation Instructions
Karen from CRESTON, IA
My dishwasher was not draining
With the help of You Tube, this 50 year old Mom got the job done. Not that complicated if you watch the step by step instructions on the Appliance Pro video. My repairman and husband were both determined to just buy a new one but this 20 year old dishwashing genius was just in need of a little repair. Only need a screwdriver, and slightly confusing as wires hook on a little different on new pumps. I suggest watching video the whole way through and then playing it step by step as you do the repair. Worked great for me. Thanks.
Read more...
Related Kenmore Dishwasher Parts
- All Kenmore Dishwasher parts
- Kenmore Dishwasher Brackets and Flanges
- Kenmore Dishwasher Caps and Lids
- Kenmore Dishwasher Circuit Boards and Touch Pads
- Kenmore Dishwasher Dishracks
- Kenmore Dishwasher Dispensers
- Kenmore Dishwasher Doors
- Kenmore Dishwasher Ducts and Vents
- Kenmore Dishwasher Elements and Burners
- Kenmore Dishwasher Filters
- Kenmore Dishwasher Grilles and Kickplates
- Kenmore Dishwasher Handles
- Kenmore Dishwasher Hardware
- Kenmore Dishwasher Hinges
- Kenmore Dishwasher Hoses and Tubes
- Kenmore Dishwasher Insulations
- Kenmore Dishwasher Insulations
- Kenmore Dishwasher Knobs
- Kenmore Dishwasher Latches
- Kenmore Dishwasher Legs and Feet
- Kenmore Dishwasher Motors
- Kenmore Dishwasher Panels
- Kenmore Dishwasher Racks
- Kenmore Dishwasher Seals and Gaskets
- Kenmore Dishwasher Sensors
- Kenmore Dishwasher Spray Arms
- Kenmore Dishwasher Springs and Shock Absorbers
- Kenmore Dishwasher Switches
- Kenmore Dishwasher Thermostats
- Kenmore Dishwasher Timers
- Kenmore Dishwasher Valves
- Kenmore Dishwasher Wheels and Rollers
- Kenmore Dishwasher Wire Plugs and Connectors