Jenn-Air Dryer Hardware

Jenn-Air Appliance Parts
Shop By Part Type

Popular Jenn-Air Dryer Hardware

Your Price
$5.52
  In Stock
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect Number PS11746840
Manufacturer Part Number WP90767
This screw is sold individually.
Installation Instructions
Alexander from Lakeland, FL
Broken Dryer Knob
First let me just say that Partselect.com is now one my stored favorites in my web browser. I came home from a business trip and saw a pair of pliers on the dryer. I thought that was odd until my wife informed me that the knob on the dryer had broken. So she was using the pliers to select the cycle. Somehow she knew where the missing pointer was actually pointing. Since the dryer was over 5 years old I saw this as an opportunity to upgrade both appliances. Not with my frugal wife. A search of the Internet popped up partselect. I ordered Wednesday morning and the parts where on my doorstep late Thursday. Trust me I was very surprised. Everything worked perfectly. Two thumbs up!!! Read more...
Your Price
$5.52
  In Stock
Screw
★★★★★
★★★★★
(3)
PartSelect Number PS11740978
Manufacturer Part Number WP3196164
This screw is sold individually.
Installation Instructions
Quail Valley from Clive, IA
Glass broken on outside oven door
Checked to see that I had all the parts I needed.
Installed bottom door trim then side trim pieces.
Do not tighten screws. Install door handle with top
trim attached over glass. Tighten screws just snug
all around.
Read more...
Your Price
$9.43
  In Stock
Blower Wheel Clamp
★★★★★
★★★★★
(3)
PartSelect Number PS11740752
Manufacturer Part Number WP312967
This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and properly. If your clothes dryer has any of the following symptoms then replacing the clamp can be a solution: making loud noises, not producing enough heat or no heat at all, and/or clothes are taking too long to dry. Make sure to unplug thedryer from power source before installing this part and refer to the installation instructions provided by the manufacturer for further guidance.
Fixes these symptoms
  • No heat or not enough heat
  • Noisy
  • Takes too long to dry
  • See more...
Installation Instructions
Tim from Jacobus, PA
Dryer was making horrible noise,
First I removed the 2 screws behind the door just below the slot for the lint trap(t-15 torx screws). I then popped the top of the dryer off using a flat tipped screw driver and using a 8mm. socket and extension I removed the 2 sheet metal screws from inside of the top corners of the front panel which attach it to the side panels. After that I could lean the front panel away from the unit and unplug the door switch being careful to mark the wires so I wouldn't have to take it apart again in the instance that I hooked them up wrong. I then leaned the front panel out a little more and lifted it off of the pins that lock the bottom of the front panel in. After that, I removed the sheet metal screws(8 mm.) that secure the fan housing cover and removed the old fan which was easy as it had spun the center out of itself and basically fell off, this is what was making all the racket. I removed the c-clip which rides in the groove at the end of the shaft with a flat tip and a pair of pliers, slid the new fan blade over the shaft, gave it a few light taps with the end of a hammer handle to seat it properly and installed the tension clamp with some pliers and popped the c-clip back on. I reversed the tear down procedures and reassembled the drier. Thanks to a little no-how, mechanical inclination, and the right parts, I was able to restore my drier to like new, virtually silent operation for about $40 as opposed to buying a new unit or paying a repairman $80 to $100 per hour plus parts to do the job. PartSelect.com made specifying and ordering the correct parts the first time a breeze and their prices are a bargain to boot.
Thanks,
Read more...
Your Price
$5.52
  In Stock
Screw
★★★★★
★★★★★
(1)
PartSelect Number PS11745622
Manufacturer Part Number WP8281196
Sold individually.
Installation Instructions
Carol from Monroe, NY
Refrig making a lot of noise
The motor kit had only two wires coming out of it. The existing one in the refrig had 6. I spliced the 2 red to one black on the new part and 2 white to the other black wire on the new part. The two green I attached to a screw. I left the 6 wire harness in place just cut off the plug piece that went into the old motor, and spliced all my wires.
Worked great!
Read more...
Your Price
$5.52
  In Stock
Screw
★★★★★
★★★★★
(1)
PartSelect Number PS11742754
Manufacturer Part Number WP489478
Sold individually.
Installation Instructions
Michael from Torrance, CA
lower left shelf support was broken
I removed all contents from the lower shelf. I, then removed both of the pull out drawers. Secondly, I removed the lower glass shelf and the glass support tray. At this point all four plastic shelf supports were accessible. I removed the inner screw from all four supports and replaced with four new shelf supports. Then reassembled in reverse order. Very easy to do! Read more...
Your Price
$5.52
  In Stock
Screw
★★★★★
★★★★★
(1)
PartSelect Number PS11743744
Manufacturer Part Number WP681414
This screw is sold individually.
Installation Instructions
Pamelia from LA CROSSE, VA
Our washer was purchased 1/6/2006 and it started banging and walking out of its place when the washer started into the spin cycle. This would occur no matter the size of the load.
We followed the instructions show on the video. However, our model was assembled slightly different. We had to remove the screws from both sides of the side panels so that we could remove the tub from inside of the machine. Also our model only has one belt not two.
Over all it was easy considering my husband and I had never attempted to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??

Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!
Read more...
Your Price
$5.52
  In Stock
Screw, Ground
PartSelect Number PS11741183
Manufacturer Part Number WP3351614
Installation Instructions
mark from fredericksburg, VA
oven would not light
replaced the igniter in oven Read more...
Your Price
$5.52
  In Stock
Hex Nut
PartSelect Number PS11738304
Manufacturer Part Number WP112432
This 10-32-inch hex nut works with multiple appliances in your home as a fastener. This specific model is sold individually. Hex nuts usually have 6 even sides and together they are used with bolts and screws in order to hold items firmly together. This piece is a fastener that attaches one item to another. This part has several advantages, the main one being that it is universal and can be used with most pieces and appliances in your home. This hex nut is an original equipment manufacturer part, meaning it is directly sourced from the manufacturer.
Installation Instructions
Heather from Pittsburgh, PA
Incoming power hot lead broke loose from mounting block and short-circuited
First I turned off power at the service panel. Then, I pulled out the range and tried to remove the access panel. The screw which held the black lead from the incoming power to the range wiring terminal had broken loose from the mounting block. It had welded itself to the panel, so I had to pry it loose. I tried to reattach it to the mounting block, but the block was cracked.

I turned on power at the service panel and used my digital multimeter to test the AC voltage of the receptacle to make sure it fell within the correct limits.

When the new mounting block and power cord arrived, I removed the screw that held the broken mounting block to the back of the range. Then, I used a screwdriver to remove the leads that attached the old power cord to the broken mounting block and range wiring terminals. The screw and nuts which held the old black lead and range wiring terminal to the block were welded together. This was the most difficult part of the repair. I was able to back them off a little bit, but not enough to remove the range wiring terminal. While holding one end of the screw in the pliers, my Dad used the heavy duty cut off wheel on my Dremel tool to cut the screw in half and free the terminal.

Then, we reversed the process to attach the new wiring block to the back of the range, incoming power cord to wiring terminals and range wiring. We plugged it back in and had it working before my dinner party.
Read more...
Your Price
$5.52
  In Stock
Clamp-Motor
★★★★★
★★★★★
(2)
PartSelect Number PS11743369
Manufacturer Part Number WP660658
This clamp is used to secure the drive motor.
Fixes these symptoms
Installation Instructions
Eric from Fort Dodge, IA
dryer drum not turning and no air circulating
replaced motor and drum rear seal as well as idler wheels, the old rear drum seal was completly worn out, since I had it all apart, I replaced lint chute and trap seals and belt and tensioner. I spent less money on parts than if I would have bought a new dryer. The motor was the main problem as the bearings were shot. Read more...
Your Price
$5.52
  In Stock
Screw
PartSelect Number PS11741524
Manufacturer Part Number WP3400074
This screw is sold individually.

Related Parts