Jenn-Air Dishwasher Parts

Dishwasher Lower Dishrack Wheel Assembly - Gray

★★★★★

★★★★★

301 Reviews

This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult. This can happen due to normal wear and tear, and the part should be replaced if this occurs. Check your model number and user manual to make sure this part is correct. It attaches directly to the dishrack. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel. It measures roughly 3x6 inches.

Dishwasher Upper Rack Adjuster

★★★★★

★★★★★

97 Reviews

This OEM Dishwasher Upper Rack Adjuster is a grayish-black, plastic part which will require a screwdriver to install. It fits onto dishwasher rack and connects it to the track allowing it to slide in and out. If broken then the rack will no longer slide properly, and the part must be replaced. The installation has been rated as "easy" by customers. Before beginning any repair, you should unplug the dishwasher and wear gloves to protect your hands. Check your model number and user manual to see if this part is right for you! Your dishwasher should have a left and right upper rack adjuster, and both are the same part. These parts are sold individually, so if you are looking to replace both, you will need to order two parts. Please see as follows for detailed repair instructions: Release the track stops from the upper dishrack rails and pull the upper rack from the dishwasher and place it upside down on a work surface. Raise the wheels to the maximum height. Release the top of the long rear clip from the dishrack tine and push the clip down to the release point and remove it. Press the tab down on the front clip move the clip up to pull it off. Release the locking tabs on the clip in the middle of the height adjuster and remove the clip. Using a slot screwdriver pry the housing cover down and out to release the upper tabs on each side. Pry the bottom of the housing cover out of the 2 lower locking tabs. Pull the housing cover off the rack. Remove the adjuster housing and wheel assembly and repeat the procedure on the other side. Slide the vertical portion on the new wheel assembly between the fourth set of vertical tines from the back of the dishrack and rotate the wheel assembly so that it lays flat against the side. Insert a positioner clip above the rear wheel and snap the tab into the slot. Install a positioner clip on the front wheel. Position the adjuster body over the vertical portion of the wheel assembly and push in into the slots. Locking tabs at the bottom of the adjuster body engage the wheel assembly once it is fully inserted the tabs. Insert the actuator lever into the adjuster body with the thumb pad facing the front of the rack. Two half-circle cutouts on the adjuster body hold the actuator in place. Push the adjuster body down and install the adjuster cover. Install the adjuster cover mounting screws. Repeat this process on the other side of the rack. Push the upper dishrack onto its tracks.

Dishwasher Dish Rack Adjuster Kit - Left and Right Side

★★★★★

★★★★★

991 Reviews

This rack adjuster kit (Dishrack Adjuster Kit, Adjuster Kit, Dishwasher Rack Adjuster) will adjust the height of the upper rack of your dishwasher. It connects to the dishrack. The kit is constructed of grey plastic and metal, and measures approximately 12 inches wide and 6.5 inches tall. The rack adjuster can break from material fatigue or prolonged high temperature exposure. High temperature exposure can compromise the integrity of the materials. If the rack adjuster breaks, your upper rack may fall down, may be unlevel, or the door may not close. This kit includes the parts to replace the left and right-side rack adjusters and has been upgraded to a more durable metal design (2 adjuster assemblies, 1 left hand and 1 right hand actuator cover, 2 gray adjuster covers, and 2 gray adjuster housings)

Mounting Bracket

★★★★★

★★★★★

12 Reviews

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.

Door Balance Link Kit

★★★★★

★★★★★

191 Reviews

This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The kit includes two door balance links and two door balance mounts with wheels, which will replace both the left and right sides. The only tool needed is a 5/16 nut driver. Before removing the existing kit, take note of how the door balance link kit is assembled for a smooth replacement process. It is recommended to check the door springs in case they need to be replaced as well.

Silverware Basket - Gray

★★★★★

★★★★★

79 Reviews

This silverware basket is gray in color and measures 8 inches wide by 11-1/2 inches high by 12 inches deep. The silverware basket is used to hold small utensils such as forks, spoons, and knives during dishwashing. The manufacturer has redesigned this part to be a complete, full basket with a handle and covers. The basket comes apart in two pieces if you prefer to place them along the sides of your dishwasher instead of at the front section of your bottom dish rack. To prolong the life of this part, try to place utensils into the holders carefully instead of dropping them in.

Rack Track Stop

★★★★★

★★★★★

48 Reviews

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy and takes less than 30 minutes to complete. Simply snap the old part out and snap the new part into place. You will not require any tools to complete the job. This is an authentic part approved by the manufacturer.

Dishwasher Door Seal

★★★★★

★★★★★

27 Reviews

Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.

Lower Wheel Assembly

★★★★★

★★★★★

16 Reviews

The lower wheel assembly in your dishwasher allows the lower dish rack to roll in and out effectively. If you notice that one of the dish rack wheels is damaged or missing, this is the part you will need to replace it. This part consists of the wheel and axle or clip that holds it on the dish rack. This wheel assembly is sold individually. This lower wheel assembly is made of plastic, is gray in color and the wheel itself is approximately 1 and 3/4 inches in diameter. Many of our customers have rated this repair as easy. To complete this repair, simply remove the old wheel assembly, and snap the new one into place.

Dishwasher Filter

★★★★★

★★★★★

31 Reviews

This filter works with the water pump in your dishwasher. It prevents debris from entering the pump and causing damage. As a result, the filter can occasionally become clogged or damaged, and will need to be replaced. A good indication of a damaged filter is if your dishwasher is not draining or cleaning the dishes properly. This filter has a gray plastic top and bottom that are approximately 5 inches in diameter. This is a genuine OEM part that comes directly from the manufacturer. To replace the filter, simply turn it counterclockwise to unlock, and then screw in the new filter