Husqvarna Lawn Tractor Seals and Gaskets

Seal--Oil (PTO Side)

★★★★★

★★★★★

2 Reviews

This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty as Medium. This part provides a seal around the crank shaft and engine block. When installing onto the engine block around the crank shaft, use something that makes contact around the entire seal, like a large socket or pipe, and tap into place evenly, ensuring that the housing is clean and dry. If the part is broken, likely due to fatigue, there will be leaking oil, and this part should be replaced using the model number on the original part to confirm it is the right fit for your model.

Gasket--Rocker Cover This OEM Gasket Rocker Cover, which can also be called the Valve Cover Gasket, is used to provide a seal between the valve cover and engine. This is a gray-colored part, measuring 5 1/2 x 4 Inch, and it is sold individually. It can be attached using a wrench or socket. Note: this part also requires a Torque Wrench. When installing, tighten and torque in alternating patterns, following the manufacturer specficiations. You will know when it needs to be replaced when there is oil leaking around the valver cover gasket, which is a sign the part is broken, likely due to simple wear and tear or constant dryness. To make sure you are purchasing the right part, check your model number. Customers rated this repair as easy.

Gasket--Crankcase (.015 Thick)

Gasket--Exhaust This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice the presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.

Gasket--Float Bowl (Nikki)

Gasket--Intake

★★★★★

★★★★★

1 Review

This manufacturer-certified Gasket-Intake, more commonly known as the Intake Gasket, is a gray, 3 x 2 inch, individually sold part which can be installed using a Wrench or Socket and a torque wrench. This part provides a seal between the caburator and intake manifold, and can be easily installed. Just ensure you are tightening to the manufacturer specfications when repairing this part. If your engine is getting more air than fuel and appears under-powered, it may be a sign this part needs to be replaced. Try spraying a mixture of soapy water at the base of the carburator at the intake manifold with the engine running, and if the engine runs more smoothly then you have discovered the problem.

Seal-O Ring

★★★★★

★★★★★

1 Review

The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and manifold, to prevent air from entering. If your engine loses power, creates a hissing noise, or if the gasket appears damaged or your engine running improperly it may be time to replace the part. If you run the engine and spray the outside of the carburator with soapy water, you can test whether or not the gasket is leaking by listening to the sounds produced. If the sound smooths out then you've found your leaky gasket. Damage may occur over time, especially if the part dries out, and make the part appear stretched or worn out. When making this medium-difficulty repair, make sure the new gasket is fitted properly between the carburetor and intake manifold.

Seal--O Ring (Intake Manifold)

Gasket Set-Valve

★★★★★

★★★★★

1 Review

O Ring-16mm This O-ring, also known as a round seal, is an authentic OEM part used in lawn and garden equipment. It is a small, circular, rubber ring that helps create an airtight seal between the oil filter filler and engine to prevent leaking and ensure adequate lubrication. It is common for the O-ring to become brittle and lose its elasticity due to aging, and exposure to chemicals and high temperatures in the equipment. If an O-ring fails, it can result in oil leakage, leading to reduced equipment performance, and potential damage to the surrounding components. Carefully the oil ring off the sealing surface and clean the area thoroughly to ensure a proper seal for the new O-ring. Lightly lubricate the new O-ring and press it on to the sealing surface.