Husqvarna Cultivator Parts
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Husqvarna Cultivator Parts
Your Price
$6.21
In Stock
Husqvarna Cultivator Bearing
HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
PartSelect Number PS9006914
Manufacturer Part Number 532009040
The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft. Over time, the part may become worn and damaged, which you will notice if you experience a squealing or grinding sound from the wheel in question, or you notice the wheel is sloppy on the shaft.
You will need a hammer and punch to complete this repair, which most of our customers rated as easy. Make sure you tap the new bearing into place evenly inside the tire rim.
Installation Instructions
robert from EUREKA, CA
transaxle rotated forward on 2015 Husqvarna YT42DXLS
2015 Husqvarna YT42DXLS. Both transaxle support struts broke causing the transaxle rotated forward and shear transaxle mounting bracket. The transaxle was not damaged. All 3 parts required replacement. There are some good youtube videos to watch to show how to complete the repair. HINT: I removed the mower deck and placed jack stands under the frame to support the rear end of the mower. I then supported the transaxle with a floor jack. This worked great for positioning/aligning the transaxle up to the frame after the new mounting bracket was installed.
HINT: Due to the shearing of the transaxle mounting bracket, it was difficult to get a socket to seat correctly on the some of the nuts securing the transaxle to the mounting bracket. I highly recommend getting 4 new nuts because you will likely damage/strip the nut while removing it.
HINT: The youtube videos all show removing the rear tires. The rear tires can be difficult to remove; and there are some interesting youtube videos on removing stuck rear tires. If you have a stuck rear tire, you can complete the repair with the tires on; it is just a bit more challenging to squeeze your hands behind the tire to reach the bolts. I was able to only get one tire off.
HINT: If I wasn't able to do the repair with the rear tire on, my idea for getting the rear tire off was to fabricate a bracket that would work with a gear puller. The plan was to utilize the two symmetrical 1/4 inch-ish size holes in the rim to install 12" long bolts. I would then install a C-channel over the bolts, which would place the C-channel directly over the axle. I would then drill a hold in the C-channel for the gear puller bolt to go through. The shoulders of the gear puller bracket would then push against the c-channel. I was planning on using a few large fender washers on the back side of the rim to help prevent the rim from getting damaged when pulling the tire. You will be pulling the rim about 3 inches to get it off the axle.
HINT: It look four hours to repair plus another half hour of watching youtube videos; probably would have taken two hours if I didn't spend two hours trying to take off one of the rear tires that was stuck.
HINT: Since I was working under the mower, I also replaced the drive (motion) belt as preventative maintenance. Read more...
Your Price
$3.99
In Stock
Husqvarna Cultivator Ring Klip Number T5304-75
PartSelect Number PS9143890
Manufacturer Part Number 812000029
The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle.
This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.
Installation Instructions
Anthony from OLIVEHILL, TN
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.
Read more...
Your Price
$3.99
In Stock
Husqvarna Cultivator Cap Axle Black 1 50 x 1 00
PartSelect Number PS9007667
Manufacturer Part Number 532104757
This genuine black cap axle, also sometimes known as the dust cap, is around 2 inches in diamater and sold individually. Comprised of plastic, it is designed to keep debris out of the hub and axle of your lawn mower or garden tractor. Over time, your dust cap may become damaged or lost due to wear and tear. If this happens, dirt and debris can freely enter the axle and hub, causing damage.
This is an easy repair to make and does not require any tools. Just look for the cap axle on the rim of the wheel to make your repair.
Installation Instructions
Anthony from OLIVEHILL, TN
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.
Read more...
Your Price
$3.99
In Stock
Husqvarna Cultivator Clevis Pin
PartSelect Number PS9009427
Manufacturer Part Number 532132673
This clevis pin is an OEM replacement part that is compatible with various makes and models of tiller and is sold as an individual part. The purpose of this pin is to snap or break under a certain amount of pressure if your tiller is jammed, to protect the more valuable components of your tiller. Measuring at approximately 2-inches long and made of high-quality metal, replacing this pin should only require pliers to swap out the old pin for the new.
Your Price
$3.99
In Stock
Husqvarna Cultivator Washer 25/32 x 1-1/4 x 16 Ga.
PartSelect Number PS9008998
Manufacturer Part Number 532121749
This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending on the equipment, its general function is to spread the load under a bolt. Ensure you consult your owners manual or check your model number to confirm this is the washer you need for your equipment.
This part will need to be replaced when your existing one is worn or damaged. It is an easy repair according to our customers, and does not require any special tools.
Installation Instructions
Frederick from BINGHAMTON, NY
Your Price
$13.69
In Stock
Husqvarna Cultivator Handle Parking Brake
PartSelect Number PS9372920
Manufacturer Part Number 532196439
Your Price
$48.56
In Stock
Husqvarna Cultivator Lawn Tractor Mandrel Assembly
PartSelect Number PS12087499
Manufacturer Part Number 587819701
Your Price
$4.99
In Stock
Husqvarna Cultivator Extension Spring
PartSelect Number PS12608566
Manufacturer Part Number 587358401
spring.extn.42.fcs.tr.deck.drv
Your Price
$8.71
In Stock
Husqvarna Cultivator Bolt and Washer Assembly
PartSelect Number PS9020856
Manufacturer Part Number 532193003
This manufacturer-approved bolt and washer assembly is for lawn tractors.
Wear work gloves to protect your hands when installing this part.
Your Price
$4.99
In Stock
Husqvarna Cultivator Washer Hardened
PartSelect Number PS9015920
Manufacturer Part Number 532188967
This OEM hardened washer spreads load under the bolts of your lawn tractor. It is silver, made of metal, and is sold individually. Over time, the washer may become damaged due to wear and fatigue, and will need to be replaced. You may notice this part is damaged if you start hearing a grinding or rubbing noise between the tire rim and ring clip.
You will need a pair of needle nose pliers to carry out this repair, which our customers generally found easy.
You will locate the washer on the spindle, between the wheel and the ring clip.
Husqvarna Cultivator Appliance Types
Popular Husqvarna Cultivator Models
Below are the most popular Husqvarna Cultivator models we have. Enter your model number in the search box to find your model.
- 700DRT 700 Drt 96093000502, 2009-01
- 700DRT 700 Drt (2009-01)
- 700DRT 700 Drt (2008-11)
- 650RTT 650 Rtt - 96093000201 (2006-12)
- 650RTT 650 Rtt - 954329172 (2003-01)
- 650RTT 650 Rtt - 954329325 (2003-12)
- CRT51 Crt 51, Hecrt51m, 954170041, 2003-09
- CRT51 Crt 51, 954001092d, 1996-02
- CRT51 Crt 51, 1995-03
- CRT51 Crt 51 - Hecrt51k (2002-03)
- CRT51 Crt 51, 96091000205, 2008-11
- CRT51 Crt 51 - Hecrt51n (2004-01)
- CRT51 Crt 51 - 96091000200 (2006-02)
- CRT51 Crt 51 - 96091000203 (2007-02)
- CRT51 Crt 51, 96091000200, 954170041, 2006-02
- CRT51 Crt 51, Hecrt51f, 1999-02
- CRT51 Crt 51, 1998-02
- CRT51 Crt 51, Hecrt51n, 954170041, 2004-01
- CRT51 Crt 51 - Hecrt51m (2003-09)
- CRT51 Crt 51 - Hecrt51l (2003-01)
