Hoover Washer Parts

Hoover Appliance Parts

Popular Hoover Washer Parts

Your Price
$11.80
   In Stock
Hoover Washer Suspension Spring
★★★★★
★★★★★
7 Reviews
PartSelect Number PS11738823
Manufacturer Part Number WP21001598
This suspension spring is 7 inches in length, and is sold individually. It is a good idea to replace all six springs at once to maintain the same tension level. To complete this repair you will need a putty knife, 5/16ths nut driver, and a pair of pliers. The springs are located underneath the washer bin, to replace them you will need to remove the main top and front panel of the washing machine.
Installation Instructions
David from Butler, PA
Washer jumping in spin cycle (white flakes under the washer)
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING (DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK) Install the new ring, tighten the screws and put the tub back in connecting everything back up and use the 6 new springs. It really isn't that hard to do. Read more...
Your Price
$10.98
   In Stock
Hoover Washer Drive Belt - 51 inches long
★★★★★
★★★★★
25 Reviews
PartSelect Number PS11738882
Manufacturer Part Number WP21352320
This V-style drive belt measures 51 inches long and 3/8 inches wide. The belt is made to slip on the motor pulley to bring the basket up to the speed required. Continued use can result in the belt suffering from wear and tear. Replace the V-style drive belt if you notice that it looks damaged. The most common symptoms of a damaged drive belt include: a burning smell or a loud grinding noise coming from the washer; the drum will not spin, spins slowly, or will not agitate; the washer shakes and moves, will not start, or will not drain.
Fixes these symptoms
Installation Instructions
Ranse from Layton, UT
Pump was making a grinding noise
The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it. Read more...
Your Price
$11.18
   In Stock
Hoover Washer Lid Hinge
★★★★★
★★★★★
25 Reviews
PartSelect Number PS11741780
Manufacturer Part Number WP35-2044
The lid hinge on your washer is connected to the lid and allows it to open and close. If you find you cannot open or close the lid to your washing machine properly, you may need to replace the lid hinge. This lid hinge is an inch and a half long, all white in color, and it is made entirely of plastic. To complete this repair, you will need a Phillips screwdriver and a putty knife to remove the top of the washer, in order to access the screws that hold the lid hinge in place. Be sure to disconnect the power to the washing machine before beginning this repair.
Fixes these symptoms
Installation Instructions
Allen from North Little Rock, AR
One of the plastic hinge pins brroke
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated. Read more...
Your Price
$13.11
   In Stock
Hoover Washer Snubber Ring
★★★★★
★★★★★
16 Reviews
PartSelect Number PS11738845
Manufacturer Part Number WP21002026
The snubber ring is a piece that is specific to your washing machine. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the leg and the dome assembly. If during your spin cycle you notice your washer jumping and making loud whirring noises, you may need to replace your snubber ring. The tools you will need for this repair include: a putty knife, a 5/16 nut driver, a 1/4 inch nut driver, a 3/8 socket and a ratchet, a small flat blade screwdriver, a pair of locking pliers, and a pair of slip joint pliers.
Fixes these symptoms
  • Shaking and Moving
  • Spins slowly
  • Will not agitate
  • See more...
Installation Instructions
David from Butler, PA
Washer jumping in spin cycle (white flakes under the washer)
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING (DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK) Install the new ring, tighten the screws and put the tub back in connecting everything back up and use the 6 new springs. It really isn't that hard to do. Read more...
Your Price
$69.83
   In Stock
Hoover Washer Transmission Pulley and Bearing Kit
★★★★★
★★★★★
16 Reviews
PartSelect Number PS2003651
Manufacturer Part Number 12002213
This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race washer. These genuine Whirlpool parts are plastic and are not sold individually. The kit is used to help the washer drain, and may need to be replaced if the washer is experiencing slow or no spin, will not drain, or has no agitation. The washer will need to be tilted on its back or side to access the bottom. The tools needed to complete this repair are a small flat blade screw driver and a pair of slip joint pliers.
Fixes these symptoms
  • Burning smell
  • Spinning Issues
  • Spins slowly
  • See more...
Installation Instructions
James from Hueytown, AL
Washer tub would not spin, pump would empty water from tub.
Lay washer on front, removed belt. Removed center pulley with thrust bearing (pulley was worn on upper end, against thrust bearing, thrust bearing was worn also). Installed new thrust bearing & pulley kit. Cleaned & lubed slots that motor insulators slide in, installed new belt. Read more...
Your Price
$7.76
   In Stock
Hoover Washer Hose Clamp
★★★★★
★★★★★
1 Review
PartSelect Number PS11743008
Manufacturer Part Number WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
Fixes these symptoms
Installation Instructions
jeff from lindenhurst, IL
Washing Machine was leaking water
Loosened the hose clamp, removed the injector valve and injector nozzle assembly, replaced both and tightened with new hose clamp. Fixed the problem for less than $20!! Washing machine is 20 years old and this was the first problem--hopefully it is now good for another 20 years! Read more...
Your Price
$84.63
   In Stock
Hoover Washer Drain Pump with Pulley
★★★★★
★★★★★
24 Reviews
PartSelect Number PS11741799
Manufacturer Part Number WP35-6465
This drain pump with pulley, also known as the washing machine drain pump assembly, is a pump with two ports. The function of this pump is to help expel water from your washing machine. The pump is activated after the spin speed has been maintained for a specific period of time and is driven by the same drive belt that also runs the transmission pulley. If your washer is not draining properly the pump could be clogged by a small object or could be broken and in need of replacing. Tools you will need for this repair include a 5/16 nut driver, a putty knife, a 3/8 socket with a ratchet, and a pair of slip joint pliers.
Fixes these symptoms
Installation Instructions
David from Boca Raton, FL
washing machine was making alot of noise
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again. Read more...
Your Price
$120.13
   In Stock
Hoover Washer Drain Pump
★★★★★
★★★★★
28 Reviews
PartSelect Number PS11741803
Manufacturer Part Number WP35-6780
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If your machine is not draining properly or if it is noisy and shakes during operation, you may need to replace the drain pump. This is a redesigned part. The pump now mounts on to the base of the washer. This product is made of white plastic and has a metal center. Before you can replace the drain pump, you will have to disengage the drive belt under the machine. To reach the drain pump you will need to remove the access panel on the backside of the washing machine.
Fixes these symptoms
Installation Instructions
Ranse from Layton, UT
Pump was making a grinding noise
The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it. Read more...
Your Price
$22.28
   In Stock
Hoover Washer Lid Hinge Pin
★★★★★
★★★★★
10 Reviews
PartSelect Number PS11741781
Manufacturer Part Number WP35-2045
This lid hinge pin allows a washing machine lid to pivot open and closed properly. The hinge pin may need to be replaced if the lid will not open or will not close. The part is white and made of plastic. This lid hinge pin is just over an inch long, is sold individually, and does not include the mounting screw (consider ordering mounting screw if it rusted or stripped). It is recommended to check the opposite lid hinge pin before ordering because hinges may wear at the same rate. Be sure to not tighten the mounting screw to pin too tightly to avoid breaking the new part.
Fixes these symptoms
Installation Instructions
Allen from North Little Rock, AR
One of the plastic hinge pins brroke
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated. Read more...
Your Price
$163.40
   In Stock
Hoover Washer Motor with Pulley
★★★★★
★★★★★
6 Reviews
PartSelect Number PS11738839
Manufacturer Part Number WP21001950
This motor is a 2 speed, 1/2 HP, 120V, 60Hz.
Fixes these symptoms
  • Burning smell
  • Will not agitate
  • Will not drain
  • See more...
Installation Instructions
Michael from Warminster, PA
The belt and pulley on the drive motor broke
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the base, replace the pulley on the shaft (you may need to break or pry the old pulley off) install the new pulley making sure it is all the way up the shaft locking the tabs into the shat groove. Reinstallmotor to the base. To replace the belt, tilted the unit backwards to access the pulleys from the bottom and installed.
Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.
Read more...

Hoover Washer Appliance Types

Related Hoover Washer Parts

Popular Hoover Washer Models

Below are the most popular Hoover Washer models we have. Enter your model number in the search box to find your model.