Hardwick Refrigerator Ice Makers

Hardwick Appliance Parts
Shop By Part Type

Popular Hardwick Refrigerator Ice Makers

Your Price
$130.33
  On Order
Replacement Ice Maker
★★★★★
★★★★★
(111)
PartSelect Number PS2121513
Manufacturer Part Number D7824706Q
This ice maker (Ice Maker Assembly, Refrigerator Ice Maker) produces ice cubes that are ejected into the storage bucket. It is located in the freezer section of your appliance, mounted on the freezer wall. The ice maker can break from normal wear and accidental damage. If this happens, your refrigerator may no longer make ice cubes, or may not make enough cubes, and the part should be replaced. This model measures approximately 11 inches long and 5 inches wide. It’s constructed of plastic and metal, and comes in black/white/silver. This assembly includes the ice mold and the control device.
Fixes these symptoms
  • Ice maker dispenses too little ice
  • Ice maker dispenses too much ice
  • Ice maker not making ice
  • See more...
Installation Instructions
Bernie from Diamond Bar, CA
Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment.
Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall.
Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer.
Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit.
Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable.
A good push of the new unit towards the snap-ins along with some upward force will get it stable.
Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in.
It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient.
Dump the first couple of batches of cubes just to make sure you're free of any residue.
Read more...
Your Price
$29.28
  In Stock
Water Fill Cup and Bearing
★★★★★
★★★★★
(9)
PartSelect Number PS11743318
Manufacturer Part Number WP628356
This refrigerator ice maker fill cup dispenses the water into the ice cube mold during the fill cycle. Replacing the water fill cup is a possible solution if you notice that the ice maker is leaking, or not making/dispensing ice. If you notice the fill cup has been damaged or cracked; replace the part straight away. This water fill cup is a genuine OEM part and will fit most refrigerators, but check the list of compatible brands to make sure yours is included before purchasing.
Fixes these symptoms
  • Ice maker dispenses too much ice
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
David from Chester, CA
The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover which is snapped in place, then removing two recessed screws at the front. I removed the broken part, I then reassembled the ice maker with the new part. I replaced the two recessed screws at the front and snapped on the cover. Then I reinstalled the ice maker in the refrigator by plugging in the harness, slipping the ice maker over the loosened screws in the refrigerator and replacing the screw that was removed from the underside bracket. Tightening all the screws completed the project. Read more...
Your Price
$37.75
  In Stock
Ice Maker Shut-Off Arm
★★★★★
★★★★★
(1)
PartSelect Number PS11743571
Manufacturer Part Number WP67004028
The icemaker shut off arm, used in a refrigerator, gives the icemaker a signal to stop making ice once the bin has a reached a certain limit. This helps monitor ice production. If your icemaker is not making ice properly or consistently, replacing this part could be a solution to your problem. The tools required for this installation are a 1/4 inch nut driver, a Phillips screwdriver, and needle nose pliers. Refer to the manual guide provided by the manufacturer for further guidance and instructions. Remember to safely store food when the refrigerator power is off to keep it from deteriorating.
Fixes these symptoms
  • Ice maker dispenses too much ice
  • Ice maker not making ice
  • See more...
Installation Instructions
Thanh from Anaheim, CA
Ice Maker Making Large Block of Ice, Level Broken, Pantry Cover broken
Pantry Cover:

I just slided out the tray, and unscrewed the left pantry panel that was broken, and replaced it with the new one, then put in the new cover after sliding the trays back in.

Ice Maker:

I unplugged the power connector in the back, unscrewed the ice maker with a flat screw driver (3 screws), slide it out, and then unplugged the wiring from the old ice maker and put it into the new one, mounted the new ice maker back in, make sure the lever is working, and then closed the freezer to let it cool down so that water can start flowing to it when it becomes cold enough (took about a good hour or so before water started filling the ice maker). Once the freezer was cold enough, water started filling the ice maker, and it begin making ice again.
Read more...
Your Price
$5.67
  In Stock
Ice Maker Front Cover
★★★★★
★★★★★
(2)
PartSelect Number PS11752097
Manufacturer Part Number WPW10289690
Your Price
$84.54
  In Stock
Ice Bucket
★★★★★
★★★★★
(3)
PartSelect Number PS11743447
Manufacturer Part Number WP67001255
The ice bucket in your freezer catches and holds the ice when it is released by the icemaker. If your ice bucket is cracked or damaged, you may need to replace it to prevent a potential leak. This part is made of white plastic and is sold individually. This ice bucket is approximately 15 inches long by 12 inches wide. Many of our customers have rated this repair as very easy. To complete this repair, simply remove the old ice bucket and replace it with the new one. Be sure to remove any broken pieces of the old ice bucket before replacing it.
Installation Instructions
ROBERT from FLAGLER BEACH, FL
ice maker stopped making ice
I loosened the two top screws, removed the bottom screw, lifted up on ice maker and slid it off, unplugged the wire from refrig. I transfered the wire to the new icemaker, pluged it back in, placed it on the two screws, installed lower screw, tighten top screws. Total time spent less than 15 minutes. The ice maker cost $125.00 with freight. Sears wanted $374.00 Read more...
Your Price
$28.81
  On Order
Ice Bin Drive Ring
★★★★★
★★★★★
(1)
PartSelect Number PS11743163
Manufacturer Part Number WP61003336
This drive ring is three inches in diameter. It is all white in color and is made of plastic. This ring is used with a refrigeraor's icemaker assembly.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
Robert from Groveport, OH
The drive ring broke which kept the bin from despensing ice.
First I removed the screws from the front of the ice bin which freed up the drive mechanism. I then removed the drice ring and replaced it with the part from Parts Select and then replaced the screws on the front. A very simple procedure.
The chill department door was an easy snap in replacement..

I would like to add that I was very pleased with Parts Select. Locating the parts I needed was very easy and I received them the next day. When The door first broke I was told I would have to replace
the whole assembly which I was not willing to do
at a quoted price of about $350.00. Needless to say I was very happy to locate Parts Select and was very pleased with everything. I have since told family and friends about Parts Select.
Read more...
Your Price
$36.43
  On Order
Ice Stripper
★★★★★
★★★★★
(2)
PartSelect Number PS11739041
Manufacturer Part Number WP2182124
This is an authentic appliance part that is sourced directly from the genuine manufacturer. This ice stripper functions by stripping the ice maker mold of ice during the ejection cycle, after the water has frozen into cubes. The ice stripper rotates to push the cubes into the ice bucket and prevents the ice from falling back into the mold. You may need to replace the ice stripper if your ice maker is no longer making ice. This part is approximately 9 inches long and is sold individually.
Fixes these symptoms
  • Ice maker not making ice
  • Ice maker won’t dispense ice
  • See more...
Installation Instructions
Kenneth from New Braunfels, TX
Ice stripper broken on ice maker
I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes! Read more...
Your Price
$84.54
  In Stock
Dispenser Solenoid
PartSelect Number PS11743220
Manufacturer Part Number WP61005253
Installation Instructions
Bill from Flowery Branch, GA
Icemaker was giving crushed ice only
First I rolled the fridge out and unplugged the power cord. I then removed the ice bin. There was one screw to the left under the ice bin rack holding it in. After removing that screw, I could pull the rack out far enough to disconnect the electrical connector. You have to squeeze the wings b-4 you can pull the connector loose. I put the rack on the countertop, removed two screws and the solenoid with plunger came out. I replaced the old solenoid, put everything back together, and realized I probably just saved myself $300. My Wife thinks I'm a Hero again. It works fine now. Read more...
Your Price
$86.31
  On Order
BIN- ICE
PartSelect Number PS11743463
Manufacturer Part Number WP67001620
This part holds the ice until it's ready to be dispensed.
Your Price
$38.58
  In Stock
Ejector Arm
PartSelect Number PS11743312
Manufacturer Part Number WP627843
This is an ejector arm, and it is used in conjunction with your refrigerator. The function of this part is to act as a cube ejector inside your ice maker. The arm will rotate inside the ice maker to allow the ice cubes to fall out of the marker and into the ice bucket. This part is made entirely of plastic, is white in color, and has eight teeth. It measures just over 9 inches long, and one and a half inches wide. To make this installation the tools you will need include a quarter-inch nut driver, a flat-head screwdriver, and a Phillips screwdriver.
Fixes these symptoms
Installation Instructions
Mary L. from Millsboro,, DE
Ice maker ejector arm broke into.
Removed old ejector arm and installed new part. Read more...

Related Parts