General Electric Range Wire Plugs and Connectors

General Electric Appliance Parts
Shop By Part Type

Popular General Electric Range Wire Plugs and Connectors

Your Price
$8.97
  In Stock
Terminal Block Kit
★★★★★
★★★★★
(25)
PartSelect Number PS470125
Manufacturer Part Number 5303935058
This part connects the wire harness to the surface element and is used for ranges. The kit includes interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing, and wires. If your range/oven is having symptoms such as burner not heating, heating elements not working, burning smell, or if the oven is making a buzzing noise then this could be the solution. The tools needed to replace the kit are wire strippers, a heat gun or hair dryer, and #1 square heard screw driver. Refer to the installation/instructional video for further guidance to accurately replace the element.
Fixes these symptoms
Installation Instructions
Steven from Taylors, SC
rental property stove only had 2 working burners and bottom drawer off track
first i took out burners then i took out the screws of the termnal block bracket. i then raised the lid on the stoveand clipped the wires on all 4 of the terminal block kits.i then slipped the shrink wrap on wires and used the wire nuts to connect wires together then heated the shrink wrap. I then put screws back in terminal block brackets. I then put the burners on while looking under lid so i would know they were making good connections as this is a bad design from factory. if you pull out burners to clean them and they are not put back in right you dont have a good connection and that causes the terminal blocks to get hot and melt. thats what happened in my case.
As far as the drawer glides they just snap into place
Read more...
Your Price
$16.90
  In Stock
Surface Burner Terminal Block Kit
★★★★★
★★★★★
(23)
PartSelect Number PS783534
Manufacturer Part Number WB17T10006
This kit includes the female contact with wires, terminal block and mounting clip.
Fixes these symptoms
Installation Instructions
Americus from Pittsburgh, PA
Burned out block
Watched a repairman do it the last time for $200.00. This time I unplugged the stove, unscrewed four screw nuts holding the upper rear cover, unplugged old wires, reconnected new ones, fed them thru to the front, attached them to the new block, screwed the block into place, replaced back cover, stuck the element into place, made my little brother plug it back in and turn it on first. It worked. Cost me $20.00 to do what the repairman did the last time. I also replaced the reflector pans. No-brainer. Read more...
Your Price
$24.41
  In Stock
Surface Burner Terminal Block Kit
★★★★★
★★★★★
(15)
PartSelect Number PS242972
Manufacturer Part Number WB2X8228
Also known as receptacle.
Fixes these symptoms
Installation Instructions
Robert from Mt. Vernon, IN
The Bake-o-lite (Hard Plastic) block that holds the burners female connection in place had chipped away over time and wouldn't allow the male part of the burner to connect up correctly.
After unplugging the range I took the rear sheet metal panel at the top off with a nut driver to expose the wiring connections. The next step was to remove the single screw holding the old part in place. (under the drip pan) Once free I snipped the old part from the wires and then taped the new female ends to the old wires with black electrical tape. From rear I carfully pulled the old wires through the back until I could reach the new wiring connections. Unplugged old, plugged in new and replaced the rear metal cover. Then I put the screw that holds the new block bracket in place, replaced drip pan, and burner. The final step was to plug the range back in and check to see if the burner worked. It did and I was done. Approx. 5 minutes Read more...
Your Price
$29.98
  In Stock
Terminal Block
★★★★★
★★★★★
(15)
PartSelect Number PS11750972
Manufacturer Part Number WPW10245259
This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness. Some symptoms replacing the terminal block could be a solution for are little to no heat when baking, element will not heat and/or it will not start. This part will prevent loosening and will reduce damage caused by corrosion (by two different metals). Refer to the instructional diagram for further replacement guidance and exact placement. You must unplug the appliance before installing this part and wear gloves to protect your hands.
Fixes these symptoms
  • Element will not heat
  • Little to no heat when baking
  • Touchpad does not respond
  • See more...
Installation Instructions
Joseph from Decatur, GA
Burned terminal block and filter board
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem. Read more...
Your Price
$56.60
  In Stock
Surface Burner Terminal Block Kit
★★★★★
★★★★★
(3)
PartSelect Number PS232606
Manufacturer Part Number WB17X210
This is a surface burner terminal block kit, also known as range surface element receptacle, for an oven, range, or stove. The kit comes with the terminal block, mounting clip, and wires. This surface burner terminal block kit connects the wiring harness to the surface elements. It is important to shut off the power to the appliance before starting this repair. You will need to remove all four elements, trim rings, and drip bowls to access the terminal block on your stovetop. This is an OEM replacement part that is sourced from the genuine manufacturer.
Fixes these symptoms
Installation Instructions
Shaohui from East Lansing, MI
There was no heat on the coils.
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe. Read more...
Your Price
$39.56
  In Stock
Terminal Block Kit
★★★★★
★★★★★
(9)
PartSelect Number PS953027
Manufacturer Part Number WB17T10011
This part provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
Fixes these symptoms
Installation Instructions
jonathan from willow springs, IL
terminal block melted
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient Read more...
Your Price
$33.46
  In Stock
Terminal Block
★★★★★
★★★★★
(4)
PartSelect Number PS232646
Manufacturer Part Number WB17X5113
This kit includes one ceramic block with 6" wire leads, 2 wire nuts and 2 heat shrink with mounting bracket.
Fixes these symptoms
Installation Instructions
Richard from Apex, NC
Heating element required continuous adjustments to work.
I removed old 8" surface element and terminal block. Some of old wiring had to be cut off because of harding/cracking of old wiring. Stove was 23 years old and this burner was the most frequently used one. I soldered the new and remaining old wires together. I used the shirnk wrap that came with the terminal block to cover the solder joint. I screwed the new terminal block (one screw holds it in place - used same screw from old terminal block that was removed). I finished by inserting the new surface element. Everything works fine. In the next week or two after we use it a while, I will check wiring again to make sure there are no changes. You need to be very careful as it gets very hot under the burner. Read more...
Your Price
$6.24
  In Stock
CLIP RECEPTICAL
PartSelect Number PS1154856
Manufacturer Part Number WB02K10133
Your Price
$6.46
  In Stock
Surface Burner Terminal Block Clip
PartSelect Number PS222163
Manufacturer Part Number WB01T10014
Fixes these symptoms
Your Price
$63.75
  In Stock
Meat Probe Receptacle
PartSelect Number PS1486371
Manufacturer Part Number 8186589
This is just the receptacle. Meat probe is sold separately.

Related Parts