General Electric Microwave Oven Combo Elements and Burners
Popular General Electric Microwave Oven Combo Elements and Burners
Your Price
$45.68
In Stock
General Electric Microwave Oven Combo Bake Element - 240V
PartSelect Number PS249424
Manufacturer Part Number WB44X200
This is a 240 volt bake element for your oven or range. The kit comes with two installation screws and the element. The element functions by supplying heat from the bottom of the oven to bake or cook your food. You may need to replace the bake element if your oven is not heating properly. This is a black metal part (Width 13 inches, length 16.5 inches, depth 1-1/2 inches ) which can be installed onto your range with a screwdriver. Installation is rated as "medium" difficulty. This element is the part that heats to allow cooking, and if broken or missing you'll be unable to cook. This part attaches to the lower section of the range. Refer to your model number and user manual to ensure this part is right for you. Each screw gets screwed into each wire terminal with a Phillips screw driver. Hold the wires forward to make sure the wires do not fall back through the rear of the oven. Unplug your appliance or shut off your circuit breaker to the appliance before installing the new part.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
- See more...
Installation Instructions
Beth from Matthews, NC
Replacment of the bake unit
The hardest part was removing the old nuthead screws off the old bake burner. Once those were off installing the new bake element was simple. One screw in each wire terminal, two hex head screws to hold the unit in place. Works like a charm!
Read more...
Your Price
$60.63
In Stock
General Electric Microwave Oven Combo Bake Element - 220V 2300W
PartSelect Number PS249466
Manufacturer Part Number WB44X5082
This bake element goes in the bottom of your range and is 220 volts and 2300 watts. This closed hinged style element with screw-in terminals measures at 15-1/4 inches long and 18-1/4 inches wide. The bottom bake element provides heat for baking. Tools you will need for this repair include pliers, screwdrivers, and an adjustable wrench. Before you begin this installation, remember to shut off the house circuit breaker or unplug your range. For safety purposes we also recommend wearing work gloves.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
- See more...
Installation Instructions
Wilbur from Taylorville, IL
element quit working
Unhooked electrical wiring from unit and rehooked new unit to electrical wiring.
Read more...
28% OFF
Your Price
$44.58
$61.82
In Stock
General Electric Microwave Oven Combo Bake Element
PartSelect Number PS249247
Manufacturer Part Number WB44K5012
At the floor of your electric oven is the bake element. This partially open-style element comes with push-on terminals. The bake element will likely provide most of the heat for baking. Therefore, if the oven is not heating properly, or if food is burnt on top and undercooked below, your bake element may be at fault. If you can see that the element has been separated or blistered, you should replace the part immediately. If there is no visible damage, turn the oven on and check to see if the element heats evenly. If the element is not heating evenly, or if it is not heating at all, use a multi-meter to test for electrical continuity to see if the element needs replacing.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
- See more...
Installation Instructions
Timothy from Cordova, TN
Bake element cracked on its own
Flipped the breaker. Removed shelf, Find the right size nut socket, unscrew the two screws, pull the element out a little bit, disconnect the wires (on pretty tight), pull out element, clean out any mess in the oven, compare element with new one to make sure its the same size and such, connect wires to new element, replace screws, flip breaker back, turn on for a few minutes to make sure it works. Piece of cake.
Read more...
Your Price
$31.00
In Stock
General Electric Microwave Oven Combo Broil Element
PartSelect Number PS249411
Manufacturer Part Number WB44X173
The broil element is located at the top of the oven and gives off heat in order to bake evenly. If you notice that the element is not heating up or is not cooking evenly it could be because it is broken or burnt out. The depth of the screw-on terminals is 2-3/4 inches and they are 1-1/4 inches apart. Does not include mounting bracket. All you need for this simple repair is small screwdriver. To complete this repair, you will need to first turn the oven off (or shut off the house circuit breaker), remove the two screws that are holding the old element in place, remove the two wires from the old part, and then connect them to the new part and screw back into place.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
- See more...
Installation Instructions
Harry from Rancho Santa Margarita, CA
Needed to replace cracked bake & broil element
This repair is very simple and only required about 15-20 minutes per unit. After turning off the power to your oven at the main breaker box, it's just a matter of removing two 1/4" screws and pulling out the units. The tricky part is removing the power plugs to the elements and not letting them slip back into the insulation. Once you plug in the new elements and screw them back in you are good to go. Once note, while you have everything out, it is a great opportunity to give your oven a good cleaning.
Read more...
Your Price
$71.41
In Stock
General Electric Microwave Oven Combo Bake Element
second, used nut driver to remove 2 screws on old element, pulled it from the back of the oven
third, removed 2 wires from old element (spade connectors)
fourth, connected new element and pushed back into oven.
fifth, reinstalled 2 screws securing new element
this was all done by my 15 yr old son under my supervision. Read more...
PartSelect Number PS249249
Manufacturer Part Number WB44K5013
This bake element is used in ranges and located at the bottom of the oven. The bake element supplies heat for baking. If your symptoms include: your oven is not heating evenly, not starting, or the heating is not consistent, then replacing the element can be the solution. Remove two retaining screws, make sure to disconnect the two connecters at each end of the element, and replace with the new one. Before starting this replacement, make sure the range is unplugged from the power source or shut off from the house circuit breaker. The tool needed is a Phillips screwdriver.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Oven is too hot
- See more...
Installation Instructions
Carl from Wynnewood, PA
bake element shorted out, sparking like a sparkler
first, made sure circuit breaker was offsecond, used nut driver to remove 2 screws on old element, pulled it from the back of the oven
third, removed 2 wires from old element (spade connectors)
fourth, connected new element and pushed back into oven.
fifth, reinstalled 2 screws securing new element
this was all done by my 15 yr old son under my supervision. Read more...
Your Price
$61.74
In Stock
General Electric Microwave Oven Combo Surface Element - 8 Inch - 2350W
PartSelect Number PS243868
Manufacturer Part Number WB30M2
The surface element, also known as the coil surface element, transfers heat to the area on top of range. The element is 8 inches in diameter. If your surface element does not heat, over heats, or heats inconsistently, replacing this part can be the solution to your issue. To determine whether the element is defective, use a multimeter to test it. Before installing the new element, make sure the drip bowl is properly aligned with the notch of the pan. Insert the new element into the reciprocal at a 40 degree angle. Refer to the instructions provided by the manufacturer for more guidance.
Fixes these symptoms
- Element will not heat
- Little to no heat when broiling
- See more...
Installation Instructions
John from San Ramon, CA
I needed new surface elements & burner bowls
This was about the simplest fix I've ever done. Just pulled off the old surface elements & burner bowls, wiped down the range top, and put in the new parts. Perfect fit. No problems at all. $$ well spent. ParsSelect shipped quickly, and they arrived well packaged. A+ experience all around. Thanks PartSelect. JA, San Ramon, CA
Read more...
Your Price
$81.25
In Stock
General Electric Microwave Oven Combo Broil Element - 240V
So, I shorted out one of the wires. Then I turned off the power but was afraid to go any farther.
An appliance repairman was at my house that day fixing my dryer seal. He was able to pull the wires through the insulation successfully and install the broiler element. He did not charge me any extra for this little extra job. But I learned my lesson. Cut the power before you begin! He told me that I could have wound up with a much bigger repair if the short had been in the wire that is connected to the control panel of the oven. I was very lucky! Read more...
PartSelect Number PS249244
Manufacturer Part Number WB44K5009
This OEM-sourced broil element with push-on terminals is located on the roof of your oven cavity, providing heat from above to cook and heat your food. It requires a 240-volt power supply to function properly. The element measures 13 1/4 inches in width and has a length of 15 7/8 inches from the mounting bracket to the back. If you are experiencing issues like uneven broiling or lack of heat, it is likely that the broil element is faulty and needs replacement. Before starting the replacement process, ensure that you turn off the oven at the breaker panel and let it cool down. To carry out the repair, you will need a flathead screwdriver, nut driver, and pliers. Begin by removing the oven door and racks. Then, unscrew the mounting screws that hold the old element in place and disconnect its wiring. Carefully pull out the old element from the appliance. When installing the new element, slide the wire contacts onto the terminals, insert it into the designated slot, and secure it with its fasteners. The top of the element is held in place by fork-like support clips, which are sold separately from the element itself.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Little to no heat when broiling
- See more...
Installation Instructions
Dianne from Rockville, MD
The broiler element caught fire and burned out while I was broiling a steak.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches, but I had not turned off the power.So, I shorted out one of the wires. Then I turned off the power but was afraid to go any farther.
An appliance repairman was at my house that day fixing my dryer seal. He was able to pull the wires through the insulation successfully and install the broiler element. He did not charge me any extra for this little extra job. But I learned my lesson. Cut the power before you begin! He told me that I could have wound up with a much bigger repair if the short had been in the wire that is connected to the control panel of the oven. I was very lucky! Read more...
Your Price
$34.89
In Stock
General Electric Microwave Oven Combo Surface Element - 6 Inch - 240V
PartSelect Number PS243867
Manufacturer Part Number WB30M1
If you notice that your surface element will not heat properly, you may need to replace it. This surface element is 6 inches in diameter and 240V. It is a Y-frame surface burner element with five turns and a metallic center medallion. When completing this repair, if you notice any signs of corrosion or overheating on the terminal, you may want to consider replacing the terminal block as well as the surface element. Many of our customers have rated this repair as easy. To complete this repair, simply tilt the old element up and remove it, and then replace it with your new one.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
John from San Ramon, CA
I needed new surface elements & burner bowls
This was about the simplest fix I've ever done. Just pulled off the old surface elements & burner bowls, wiped down the range top, and put in the new parts. Perfect fit. No problems at all. $$ well spent. ParsSelect shipped quickly, and they arrived well packaged. A+ experience all around. Thanks PartSelect. JA, San Ramon, CA
Read more...
Your Price
$91.04
In Stock
General Electric Microwave Oven Combo Bake Element - 3400W
I removed the two screws that hold the element in place. I then pulled the element out slowly about 2 inches to expose the connectors, and then disconnected the two wires by holding the wire (female) connector by one plier and pull the element (male) connector out with another plier. Then, insert the new element connectors, and push the wire back into wall then fasten the element with 2 screws. Read more...
PartSelect Number PS249293
Manufacturer Part Number WB44T10018
This bake element is found on the bottom of the oven.
Fixes these symptoms
- Element will not heat
- Little to no heat when baking
- Oven not heating evenly
- See more...
Installation Instructions
Yungti from Tomball, TX
Broken element
First, disconnect the power from the electrical box, not just turn off that oven. specially if you have a double oven. Just turn one off is not enough.I removed the two screws that hold the element in place. I then pulled the element out slowly about 2 inches to expose the connectors, and then disconnected the two wires by holding the wire (female) connector by one plier and pull the element (male) connector out with another plier. Then, insert the new element connectors, and push the wire back into wall then fasten the element with 2 screws. Read more...
Your Price
$156.75
In Stock
General Electric Microwave Oven Combo Dual Radiant Element - 9 Inch
1. Turn off the breaker for the cooktop.
2. Remove (2) 1/4" hex screws directly under cooktop. You may need to open oven door to reveal them.
2. Prop up cooktop. I used the box the replacement element came in.
3. The element is held in place with (3) brackets held in by a #2 philips screw each. Mark the location of each of the brackets. There are numbers on the element to help you do this.
4. Write down where each of the wires connects to the element. There's only a few of them, but I tend to forget that stuff. The wires have female spade-type connectors that connect to the male ends on the element.
5. Using a needle-nose or small pliers wiggle each wire off the element. Grab the wires by the end of the female connector when you do this. I found it helpful to use a small flat screwdriver to help pry them off. Mine were on pretty tight, so expect this to take a few mins. If you have problems getting to the wires, remove the brackets (next step) first and come back to this one. I let the element hang from the wires without any problems, but I still wouldn't recommend it.
6. Remove each of the screws with a #2 philips screwdriver. Support the element with your hand and gently pull each bracket away from the element. Once they're all gone, the element should just come out. I took a look at my old element and saw that the large burner wires were melted in a couple places, so it was definitely broken.
7. If necessary, clean the underside of the cooktop surface with a clean papertowel. There was a little dust from the old element on mine.
8. Connect the new element and test to make sure it works by turning on the breaker and turning on the burner for a second or two. Note: This will make the top of the element hot for some time, so test it and go away for a few mins. If it works OK, proceed. If not, disconnect and figure out what else may be wrong.
9. Using the old element, make copies of the marks you made for the bracket locations onto the new element. You'll have to punch through the insulation when re-attaching the screws.
10. Re-wire the new element, if necessary and re-attach the brackets over the marks you made. This may be a pretty tight fit because the new element was thicker than the old on mine. I opened up the brackets a bit to make it not so hard to re-attach. Hook the brackets on and squeeze them over the element. The holes in the brackets need to line up with the holes drilled into the bottom of the element. If they don't, spin the element around (or detach and re-attach the brackets) till they do.
11. Screw in the (3) screws over the brackets pushing them through the insulation on the element.
12. Close the cooktop and reattach the hex screws under it (1/4" hex).
13. Turn on the breaker and test again.
Thats it, works great now. Good Luck Read more...
PartSelect Number PS1016539
Manufacturer Part Number WB30T10099
This is a large dual haliant element with a limiter or sensor for glass cooktops and freestanding ranges. It is a 2500-watt part. The inner diameter measures 9 inches, while the outer diameter measures 10 inches. If there is no heat generated from your element, you may need to replace this part. You may also need to check your socket or infinite switch. It is located under the glass cooktop of your appliance. Be sure to unplug or cut the circuit breaker to your appliance before starting this repair. Before replacing this part, be sure your appliance is getting enough power. If it is receiving less than the required 220 volts of alternating current, the surface element will not work.
Fixes these symptoms
- Element will not heat
- See more...
Installation Instructions
Scot from Oakland, FL
Large burner on dual element burned out
This was really easy, and pretty with no problems or issues It took me longer to write this than to do the actual installation. I used a digital camera to help me remember where things were, but a pen/paper works fine. Here's what I did:1. Turn off the breaker for the cooktop.
2. Remove (2) 1/4" hex screws directly under cooktop. You may need to open oven door to reveal them.
2. Prop up cooktop. I used the box the replacement element came in.
3. The element is held in place with (3) brackets held in by a #2 philips screw each. Mark the location of each of the brackets. There are numbers on the element to help you do this.
4. Write down where each of the wires connects to the element. There's only a few of them, but I tend to forget that stuff. The wires have female spade-type connectors that connect to the male ends on the element.
5. Using a needle-nose or small pliers wiggle each wire off the element. Grab the wires by the end of the female connector when you do this. I found it helpful to use a small flat screwdriver to help pry them off. Mine were on pretty tight, so expect this to take a few mins. If you have problems getting to the wires, remove the brackets (next step) first and come back to this one. I let the element hang from the wires without any problems, but I still wouldn't recommend it.
6. Remove each of the screws with a #2 philips screwdriver. Support the element with your hand and gently pull each bracket away from the element. Once they're all gone, the element should just come out. I took a look at my old element and saw that the large burner wires were melted in a couple places, so it was definitely broken.
7. If necessary, clean the underside of the cooktop surface with a clean papertowel. There was a little dust from the old element on mine.
8. Connect the new element and test to make sure it works by turning on the breaker and turning on the burner for a second or two. Note: This will make the top of the element hot for some time, so test it and go away for a few mins. If it works OK, proceed. If not, disconnect and figure out what else may be wrong.
9. Using the old element, make copies of the marks you made for the bracket locations onto the new element. You'll have to punch through the insulation when re-attaching the screws.
10. Re-wire the new element, if necessary and re-attach the brackets over the marks you made. This may be a pretty tight fit because the new element was thicker than the old on mine. I opened up the brackets a bit to make it not so hard to re-attach. Hook the brackets on and squeeze them over the element. The holes in the brackets need to line up with the holes drilled into the bottom of the element. If they don't, spin the element around (or detach and re-attach the brackets) till they do.
11. Screw in the (3) screws over the brackets pushing them through the insulation on the element.
12. Close the cooktop and reattach the hex screws under it (1/4" hex).
13. Turn on the breaker and test again.
Thats it, works great now. Good Luck Read more...
Related General Electric Microwave Oven Combo Parts
- All General Electric Microwave Oven Combo parts
- General Electric Microwave Oven Combo Brackets and Flanges
- General Electric Microwave Oven Combo Circuit Boards and Touch Pads
- General Electric Microwave Oven Combo Doors
- General Electric Microwave Oven Combo Drawers and Glides
- General Electric Microwave Oven Combo Glass Tray and Supports
- General Electric Microwave Oven Combo Handles
- General Electric Microwave Oven Combo Hardware
- General Electric Microwave Oven Combo Hinges
- General Electric Microwave Oven Combo Knobs
- General Electric Microwave Oven Combo Lights and Bulbs
- General Electric Microwave Oven Combo Racks
- General Electric Microwave Oven Combo Seals and Gaskets
- General Electric Microwave Oven Combo Sensors
- General Electric Microwave Oven Combo Switches
- General Electric Microwave Oven Combo Thermostats
- General Electric Microwave Oven Combo Trims