General Electric Microwave Brackets and Flanges

Your Price

$26.95

General Electric Microwave Mounting Plate Assembly

PartSelect Number PS16216996

Manufacturer Part Number WB56X35363

This mounting plate, also known as a bracket, is crucial for keeping your microwave mounted to the wall, when placed above the stove. This OEM part is sold separately from the screws that are needed to hold it in place. You will need a screwdriver in order to secure the mounting bracket into place. Part has been substituted. Part is no longer a U-shaped bracket, it is now a flat mounting plate and will function the same.

Installation Instructions

Roy from Lakewood, CO

I needed to acquire and install a mounting plate for an over the range microwave

I attached the mounting plate to the wall as directed in the installation instructions which I had downloaded from GE. This procedure took 45 minutes to complete. I was then able to mount the microwave. Read more...

Your Price

$47.95

General Electric Microwave Door Interlock Switch Bracket

★★★★★

5 Reviews

PartSelect Number PS3486543

Manufacturer Part Number WB14X10049

The door interlock switch bracket houses and supports the door switches.

Fixes these symptoms

Door stuck closed
See more...

Installation Instructions

Jay from WESLEY CHAPEL, FL

Door locks. Not opening.

Slide a Butter knife at left side by open push knob door will open. Then open all screws from top cover push cover top side front way then door locks Bracket have 3 microswitch pulls out switches mark them top medium and bottom. Remove 3 screws holding brackets will come out. On bottom see a Cam has 1/4” holes can holding Saft broken then install new door lock bracket install microswitch put 3screw and slide Cam on saft . I put a small screw on saft to hold cam on place. There was no screw . That’s why cam saft was broke. Put top cover tight all the screws and door lock fixed. Read more...

Your Price

$11.95

General Electric Microwave Cook Auxiliary Holder

★★★★★

4 Reviews

PartSelect Number PS3524335

Manufacturer Part Number 4930W1A069A

Your Price

$21.95

General Electric Microwave Panel-control Mounting

★★★★★

2 Reviews

PartSelect Number PS222449

Manufacturer Part Number WB01X10107

Installation Instructions

Richard from Arroyo grande, CA

Cracked glass, light always stays on

Problem 1: cracked outer glass
1. Remove the outer glass assembly using the four screws along the top and lifting out/up, be very careful it doesn't fall off and break on the floor. Hold the handle while removing the last screw, it can fall easily.
2. Remove the handle using the 2 long screws on the back side which feed through 2 small metal plates that were previously holding the door onto the main cavity.
(3) If there is broken glass, it helps to remove the metal ledge the glass was on using the screws underneath and clean out all broken glass fragments, to do this you may have to remove the vent panel below it to get screwdriver access.
4. Assembling the new glass panel is the same steps backwards, should be obvious.

Problem 2: Light always stays on
1. Remove the door switch panel on the left side of the microwave, 1 screw.
2. Remove the right access panel on the right side of the microwave, this is large and has many screws, and a couple also need to be removed on top.
** Don't touch any wires when doing all this, and make sure you are grounded and don't produce an electrostatic shock. **
3. Manually toggle the door latch catchers on either side (just the plastic, don't touch any wires), at the same time, and see if the light turns off. If it does, the door latches might not be putting enough pressure, they may be cracked or need to be replaced.
4. Sometimes the switches get dislodged, for example if someone slammed the microwave shut. Try nudging the switch, or one of the connectors, slightly towards the door side, or tapping it from behind with a screwdriver. If it was loose you might get an audible click when it goes back into place.

Note: if the microwave light always stays on, it eventually might shut off after a long time. Power cycle the microwave before doing the tests above, so the light is on when you toggle the door latch switches. Read more...

Your Price

$107.62

General Electric Microwave Damper Bracket

PartSelect Number PS8753754

Manufacturer Part Number WB06X10938

Introduce the superior quality of GE's Damper Bracket designed specifically for microwave appliances. The unique purpose of this assembly is to control the airflow through the vent duct by attaching firmly to the cabinet. Coming as part of an assembly, a detailed list of the included parts can be accessed via the appropriate parts diagram. Owing to the potential hazard of high-voltage capacitors that microwaves possess, it is strongly recommended that this piece be installed by a professional service technician. Invest in GE's Damper Bracket for an enduring solution that is sure to enhance your appliance's performance.