General Electric Ice Maker Hoses and Tubes

Videos!

Your Price

$26.87

General Electric Ice Maker Water Tube Kit

★★★★★

8 Reviews

PartSelect Number PS11730901

Manufacturer Part Number W10823511

This is the replacement water tube kit for your refrigerator. This tubing is made of plastic, is 1/4 inch in diameter, and comes with 2 inserts. This tube may be longer than the original tube, and may need to be cut. This water tube transports water to the ice and water dispensers. If your refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace this tube. This part is sold individually and is an OEM part sourced directly from the manufacturer.

Fixes these symptoms

Ice maker not making ice
Leaking
Not dispensing water
See more...

Installation Instructions

Trent from Tacoma, WA

water dispenser started leaking

i wasn't sure it was the inlet valve unit because the leak was at the water dispenser in the freezer door. after some research it looked like the water inlet valve located in the back lower part of the refrigerator was the problem. to replace, take off the cardboard cover, about 6 screws, you have access to the water inlet valve, disconnect the hoses (i think it goes without saying that you should have turned off the water to the frig) replace the inlet valve, connect hoses, turn water back on and you'll be back in business. very easy repair. Read more...

Your Price

$47.07

General Electric Ice Maker Water Distributor Tube

★★★★★

1 Review

PartSelect Number PS11738017

Manufacturer Part Number W10863947

The water distributor tube distributes water from the reservoir to the evaporator plate.

Installation Instructions

Gerald from ELMHURST, IL

The tunes were moldy and the pump didn't work.

The repair was fairly easy. Take out screws and lift top of ice maker but do not take off. Having 2 people to do this helps. Clean all parts with calcium deposits. Replace all moldy or broken parts. Some parts are harder to replace. The back screw of the pump is difficult to install. Use a magnetic screw driver for help holding the screw. We used a little wax to keep the screw on the driver. The ice maker works better than it has in 2 years. Read more...

Your Price

$39.84

General Electric Ice Maker Filter Drier Tube

PartSelect Number PS11728084

Manufacturer Part Number W10843121

This filter dryer is for refrigerators and filters refrigerant that travels through the sealed system of the refrigerator.

Your Price

$20.89

General Electric Ice Maker Water Line - 1/4"

★★★★★

1 Review

PartSelect Number PS292409

Manufacturer Part Number WR17X1948

This water line 1/4, also known as a ice maker fill tube, is used in freezers and refrigerators. The tube directs the water into the ice maker cup during the cycle in which it fills the cup. The water line height is 0.6 inch and it weighs 0.1 lbs. As a safety precaution, unplug your appliance from the power source before installing this part. Remember to safely store food when it is removed from fridge or freezer. Refer to the installation instructions provided by the manufacturer for further guidance and accuracy.

Fixes these symptoms

Leaking
See more...

Installation Instructions

RUSSELL from BLACK HAWK, SD

water line cracked

I loosened the compression nut on the valve with my fingers and pulled the water line free from the valve. On the other end, I just pulled it from the hose clamp. Installation in reverse. Force the water line into the fitting on top, Slide the old nut over the line on the bottom. Screw the nut onto the valve. Reach inside the freezer and turn on the ice maker. Done. Before replacing the cardboard grill, you should vacuum the coils on the bottom, front and back. If practical, push it outside and blow it out with an air compressor or a leaf blower. Read more...

Your Price

$50.22

General Electric Ice Maker Reservoir Hose

PartSelect Number PS11739073

Manufacturer Part Number WP2185626

Installation Instructions

Gerald from ELMHURST, IL

The tunes were moldy and the pump didn't work.

The repair was fairly easy. Take out screws and lift top of ice maker but do not take off. Having 2 people to do this helps. Clean all parts with calcium deposits. Replace all moldy or broken parts. Some parts are harder to replace. The back screw of the pump is difficult to install. Use a magnetic screw driver for help holding the screw. We used a little wax to keep the screw on the driver. The ice maker works better than it has in 2 years. Read more...

Your Price

$56.48

General Electric Ice Maker Hose, Overflow

PartSelect Number PS11740343

Manufacturer Part Number WP2313890

Installation Instructions

Gerald from ELMHURST, IL

The tunes were moldy and the pump didn't work.

The repair was fairly easy. Take out screws and lift top of ice maker but do not take off. Having 2 people to do this helps. Clean all parts with calcium deposits. Replace all moldy or broken parts. Some parts are harder to replace. The back screw of the pump is difficult to install. Use a magnetic screw driver for help holding the screw. We used a little wax to keep the screw on the driver. The ice maker works better than it has in 2 years. Read more...