General Electric Dryer Belts

Popular General Electric Dryer Belts

Your Price
$48.45
  In Stock
General Electric Dryer Drive Belt
★★★★★
★★★★★
187 Reviews
PartSelect Number PS16542496
Manufacturer Part Number WE03X29897
This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley, allowing all the parts to work together, spinning the drum as the motor rotates. If the drum will not turn when the dryer is turned on the belt is likely broken. It is common for belts to stretch or become brittle over time, which is what leads to the breakage. If broken, it should be replaced; the drum simply cannot spin without this belt. Refer to your model number and user manual to check if this part is right for you. Ensure you use work gloves to protect your hands from sharp internal parts during this repair. Please note: When comparing the length of your old belt to the length of the belt as stated here, remember that a small amount of stretching and contortion may occur with belts over time for a range of different reasons. Unless your belt is drastically different in length, this belt is what you are looking for despite any small inaccuracies. You will need to remove power to your appliance, remove the main panel, and access the motor drive to slip your new belt back into place.
Fixes these symptoms
  • Drum Not Spinning
  • Heat stays on after drum has stopped
  • Noisy
  • See more...
Installation Instructions
Edwin from Seattle, WA
Dryer making grinding noises
We live in a Condominium, space is tight especially in the Utility room where the washer/dryer are located. Turned dryer breaker off at the electical panel.
Removed the top cover and front assembly w/door and front drum support, right where the unit was located. Had to gain rear access to loosen drum drive belt so undid the dryer vent hose to floor connection through a front acess hole. Moved the unit out to the breakfast nook as well as disconnecting the power cable from the wall socket. Removed the rear access panel covers and unhooked the drive belt. At the front removed the top screws off the lower cross member to allow spreading of the side covers to allow the removal of the drum. Removed drum and found the bearing bushing gone, reduced to powder.
Using the supplied instuction sheet, replaced the rear bearing assembly, replaced the drum after vacumming the whole interior and started the reassembly of the unit using the new belt and moved the unit back into place. Reconnected the power cable and dryer vent then lastly replaced the lint filter and selector knob. Closed the breaker and turned on the machine, no noise!!!
Incidently I am 78 years old. Thanks PartSelect.
Read more...
Your Price
$30.99
  In Stock
General Electric Dryer Drum Belt
★★★★★
★★★★★
8 Reviews
PartSelect Number PS11705916
Manufacturer Part Number 4400EL2001F
The belt wraps the length of the dryer drum, secured by a tension pulley and then loops around the motor pulley. If you find that the drum is not turning properly or at all while your dryer is in succession, it might be due to the belt being broken.
Fixes these symptoms
Installation Instructions
Spencer from SHALIMAR, FL
Dryer would turn on but no heat to dry clothing
Unplugged dryer, pled forward to get access to back of dryer. Removed screws, enabling top, front control clip. door panel to be taken off. Lift out drum, replace heater assembly. drum belt, thermistor. Cleaned entire interior and reassembled, working good as new. All parts fit and were a exact match. Read more...
Your Price
$27.11
  In Stock
General Electric Dryer Drive Belt
★★★★★
★★★★★
27 Reviews
PartSelect Number PS2350043
Manufacturer Part Number WE12X10014
This belt has a length of 87 inches, width of 1/4”, flat, with 4 ridges.
Fixes these symptoms
Installation Instructions
Michael from Warwick, RI
the rear drum bearing was worn the dryer became very noisy
i removed the scews just above thr opened dryer door, i was then able to swing the dryer top cover back. i then removed the lower front panel screws ,the the screws securing the front of the dryer ( where the door is ) and removed it. there are just 2 wires to disconnect. after the front is removed you gain full access for drum removal, remove the belt make sure the wires are not in the way and remove the drum.i also used a vacuume to clean the inside of the dryer. the front drum slides are very easy to replace only 2 screws each.remove old parts install new parts then just put the dryer back together in the reverse order i took it apart. after re-assembly i turned the dryer on it was so quiet running my wife and dogs were very happy. ps. i just want to thank the people at partselect for having all my parts in stock and for the speed in which i received them. other than having to repair my dryer it was a very pleasant experiance. Read more...
Your Price
$27.11
  In Stock
General Electric Dryer Drive Belt
PartSelect Number PS12743316
Manufacturer Part Number WE03X29704
Your Price
$36.81
  In Stock
General Electric Dryer Drive Belt
★★★★★
★★★★★
1 Review
PartSelect Number PS16742797
Manufacturer Part Number WE03X33648
Fixes these symptoms
Your Price
$72.91
  In Stock
General Electric Dryer Drum Belt
★★★★★
★★★★★
3 Reviews
PartSelect Number PS959964
Manufacturer Part Number WE12X10009
Used to turn the drum.
Fixes these symptoms
Installation Instructions
Raul from Fountain, CO
Loud noise & clothes hanging in drum.
1. Remove power cord from wall outlet. Unlatched the top lid of the dryer by pushing a flat screwdriver under the R & L sides where a metal clip on each side holds the top down.
2. Removed the yellow clip screwed onto the top frame.
3. Removed the front frame of the dryer by unscrewing the two screws holding the front frame on – one on either side.
4. Mark w/ an (x) on same side of alignment for the 2 wiring connectors before separating them.
5. Removed the front panel by tilting it forward & lifted to unlatch it from the 2 clips at the bottom of dryer.
6. Unwound the belt encircling the drum by releasing the tension between the tensioner roller & drive pulley. (Its better to remove back access panel at this time & do this at the back since I found it necessary to do this anyway when re-installing the new belt).
7. W/ lifting motion, pulled the drum out from the plastic holder attached to the back of the dryer frame. Guided & completely removed the drum out of the dryer.
8. Unscrewed the 3 screws holding the old big bearing to the back of the drum.
8. Unscrewed the 2 screws & removed the plastic that had held the bearing at back of the frame.
8. Installed the new bearing by screwing it to the back of the drum with 3 screws. Be careful not to strip screws. Used help to hold new bearing in place & aligned w/ screws.
9. From the front, installed the plastic holder to the back of the frame by 2 screws and put the ball bearing in-between holder & the metal strip retainer coming from the back of dryer.
10. Used the grease that came with the kit on the plastic holder & the big bearing at the back of the drum.
11. Replaced w/ new belt then re-inserted the drum back into the body of the dryer frame, w/ lifting motion, re-inserted the bearing into the plastic holder.
12. Putting the belt into the drive & tension pulleys through the back access panel was easy but could be very hard to do if coming from the front.
13. Had to replace the front panel's top felt w/ glides that holds the drum at the front w/ a new one. Really important to pay attention to where the plastic glides excess portion is facing (towards front panel), otherwise the front panel might not fit when you snap it back to place.
14. Removed old felt remnants w/ blade scraper & sandpaper. Used adhesive that came w/ kit. Once tacky, put the new felt w/ glides on & used clamps to hold it in place.
15. Waited for 2 hrs. (watched a movie) then re-installed front panel. Make sure that the drum (front) lid rides on top of the plastic glides.
16. Latched bottom of front panel to the metal clips. Replace the 2 screws back into place holding the front panel.
17. Snapped the wiring connectors in place where the (x) marks align.
18. Lowered the top panel & snapped it back into place
Note: All parts came w/ fast delivery & OEM fit - very satisfied! Took my time & on every chance I cleaned & vacuumed all areas of lint & dirt since the dryer hasn't been serviced for more than 10 years...
Read more...
Your Price
$59.12
  In Stock
General Electric Dryer Belt Drive
★★★★★
★★★★★
4 Reviews
PartSelect Number PS16729246
Manufacturer Part Number WE03X32037
Fixes these symptoms
Installation Instructions
CLARENCE from ENGLEWOOD, NJ
Broken Pulley And Broken Belt
I took the dryer rear and bottom panels off after removing a total of 6 screws . I then put on a new belt and pulley after removing the dryer drum by opening the front door of the dryer unit Read more...
Your Price
$28.66
  In Stock
General Electric Dryer Belt Drive
★★★★★
★★★★★
1 Review
PartSelect Number PS8756711
Manufacturer Part Number WE12X10020
Your Price
$35.23
  In Stock
General Electric Dryer Belt Drive
PartSelect Number PS12749245
Manufacturer Part Number WE03X29259
Your Price
$86.28
  In Stock
General Electric Dryer Drive Belt
★★★★★
★★★★★
1 Review
PartSelect Number PS16659521
Manufacturer Part Number WE03X33898

Related General Electric Dryer Parts