Official General Electric Range Hood Parts

Your Price

$14.40

General Electric Vent Hood Fan Switch

★★★★★

8 Reviews

PartSelect Number PS953545

Manufacturer Part Number WB24X10129

This is the replacement fan switch for your range hood. When you turn the knob to turn the range fan on, the fan switch is actuated. If your fan will not turn on when the knob is turned, you most likely have an issue with the fan switch. The fan has a main square portion with a red center that connects to the fan control knob. The main portion is approximately 1 inch in diameter. This part is sold individually. Be sure to disconnect the power source from your range before you begin this repair.

Installation Instructions

Morgan from College Station, TX

FR Burner out and range hood switches broken

pulled oven out in the open, unplugged from outlet, removed two white front side panels, removed four screws on sides, unplugged range from harness, removed top, unscrewed two metal clips that hold element in place, gently removed wires from element using a small screwdriver and needle nose pliers and attached each one to the new element as it was removed. Reinstalled as I took apart. For the range hood, I unplugged the hood, removed the covers to the switch box and used a small screw driver to open/destroy the old switch and to save the tinned wires. I then pushed in the wires into the new switch as I removed them from the old one. Should be careful to only snug up the hex nuts as the plastic switch stem will probably break easily with a little force. Read more...

Your Price

$19.82

General Electric Vent Hood Fan Blade

★★★★★

14 Reviews

PartSelect Number PS952006

Manufacturer Part Number WB02X11025

This part is the replacement fan for your range hood. It is made of white plastic and is approximately 7 inches in diameter. The fan blade helps to dissipate smoke and smells from your range. The main reason you would want to repair the fan blade is if it is damaged, and will not rotate. To remove the fan, use a pair of pliers to grab the retaining clip, and pull the fan blade off the shaft of the motor. This part is sold individually and is an OEM part sourced directly from the manufacturer.

Installation Instructions

Danny from DICKSON, TN

Exhaust fan broke

Pulled filter, pulled little clip that holds fan on to motor shaft. Placed new fan on (make sure turned right way, hard not to) put clip in place put filter back on. Done. Read more...

Your Price

$12.98

General Electric Vent Hood Light Switch

★★★★★

6 Reviews

PartSelect Number PS953546

Manufacturer Part Number WB24X10130

This is the replacement light switch for your range. It comes with the actual switch, and the hex nut that goes with it. The switch is approximately 1 ¼ inches by 1 ¼ inches, and the hex nut is approximately ½ an inch in diameter. When you press the switch, it allows you to turn the range light on and off. If the light does not come on when you hit the switch, you may need to replace it. Be sure to disconnect your microwave from the power source before you begin this repair. This part is an authentic OEM part sourced directly from the manufacturer.

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

Joseph from FLORENCE, NJ

The plastic part of the switch that screws into the hex nut broke off.

First, unplug the range hood, then remove the switch cover plate, held by two Phillips screws. Remove the switch knob and the hex nut on the front of the hood.(In my case, the hex nut had snapped off with the threaded part of the switch in it.) Then gently pull the switch away from the hood and write down which color wire (black, yellow, white) connects to which receptacle on the switch. The receptacles on the rear of the switch are marked L,1,2 and 3. 3 is left blank. Snip the wires from the switch, getting as close to the body of the switch as possible. Pulling them from the push-in receptacles doesn't work. Using a wire stripper, strip off about 1/2 inch of the wire insulation. Twist the exposed wires tightly and insert into the appropriate receptacles so that no bare wire shows. Insert the face of the switch into the hole on the hood so that the threaded portion protrudes. Using the hex nut provided, tighten snugly with an adjustable wrench. Do not over-tighten. Reattach the knob. Most of this repair went quickly and smoothly, but, despite repeated efforts, the threaded portion of the new switch did not fit through the original hole in the hood. As a result, I used a drill to enlarge the hole. The result was satisfactory but the new switch is not seated as well as the original. The knob does not line up exactly in the On, Off, Nite Light positions. Read more...

Combination Grease and Odor Filter – Part Number: WB02X10700

Your Price

$27.03

General Electric Vent Hood Combination Grease and Odor Filter

★★★★★

8 Reviews

PartSelect Number PS223976

Manufacturer Part Number WB02X10700

This is a combination grease and odor filter and it is designed for your range hood and microwave. This part removes grease and odors by filtering the air while you are cooking. The most common reason for needing to replace this part is if your older model has worn and dirtied over time. This part is roughly 9 inches long by 11 inches wide. The combination filter has a half-inch frame and the entire filter is chrome colored.

Installation Instructions

Helen J. from Landisburg, PA

Replace grease and oder filter

To replace a filter, on my range, i just pull down on the old ,and push up tp place the new one in. the were no screws ,to take out. I would like to say, that the time it took , to place my order and recive it was great. i could not be more pleased . i will be in touch, again, whenever, i need a part ! thank you. Read more...

Your Price

$34.63

General Electric Vent Hood LIGHT BULB

★★★★★

3 Reviews

PartSelect Number PS11773829

Manufacturer Part Number WB25X24863

Your Price

$21.37

General Electric Vent Hood LAMP SOCKET

★★★★★

3 Reviews

PartSelect Number PS12170321

Manufacturer Part Number WB18X27245

This lamp socket is designed for use in range hoods. It is an authentic manufacturer replacement that holds the light bulb securely and provides the electrical connection needed for the bulb to function. If the socket has a loose/faulty connection, or it is damaged or worn-out, the light bulb will either fail to turn on or it will flicker. Ensure that the range hood is disconnected from power before beginning this replacement. Pull the light bulb cover off and gently twist the light bulb off. Carefully remove the faulty socket by twisting it counterclockwise and disconnecting it from the wiring. Position the new socket on the mounting surface and reattach the wire connectors. Insert the bulb into the socket and reattach the protective cover/lens.

Installation Instructions

T from MACCLENNY, FL

Lamp socket broke.

Pulled stove out. Turned switch off to hood lights. Checked power with power indicator tool, make sure off. Remove plate. Remove socket, cut wires, place wires in new socket . Replace plate. Read more...

Your Price

$10.64

General Electric Vent Hood FAN CLIP

★★★★★

1 Review

PartSelect Number PS952007

Manufacturer Part Number WB02X11026

Installation Instructions

Gabriela from ELIZABETH, NJ

The fan wars broken and the filter gross

Was so simple just take out the filter the clip and the fan and then put the new parts thank you Read more...

HALOGEN LIGHT BULB – Part Number: WB08X34831

Your Price

$32.24

General Electric Vent Hood HALOGEN LIGHT BULB

★★★★★

5 Reviews

PartSelect Number PS16216949

Manufacturer Part Number WB08X34831

Sold individually.

Your Price

$78.23

General Electric Vent Hood GREASE FILTER

★★★★★

2 Reviews

PartSelect Number PS11726662

Manufacturer Part Number WB02X24872

This vent hood grease filter is specially designed to fit with ranges. It is made of metal and has measurements of approximately 12 inches by 12 inches. The filter is responsible for trapping grease and other cooking particles and preventing them from entering the ductwork and recirculating inside the kitchen. This helps to improve the quality of air inside your kitchen and prevents unpleasant odors from developing. It is recommended to regularly clean your grease filter to prevent the buildup of food residues and keep your range running efficiently.