Electrolux Washer Springs and Shock Absorbers

Electrolux Appliance Parts
Shop By Part Type

Popular Electrolux Washer Springs and Shock Absorbers

Your Price
$53.18
  In Stock
Shock Absorber Kit
★★★★★
★★★★★
(19)
PartSelect Number PS3508101
Manufacturer Part Number 5304485917
This shock absorber kit is an authentic OEM part that is sourced directly from the manufacturer. The kit includes two dual-stage shock absorbers, one spare shock mounting pin, and four locking nuts. These shock absorbers keep your front-load washer from shaking vigorously by absorbing and reducing vibrations from the wash and spin cycles of your appliance. This kit comes with two shock absorbers because it is recommended to replace both at the same time, as they wear at the same rate. To access your washer shock absorbers, simply remove the lower access panel after disconnecting the power to the appliance.
Fixes these symptoms
Installation Instructions
Douglas from Medical Lake, WA
Both vibration shock absorbers broken
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could say that it all went well from there but......when the shocks broke, apparently the hit the motor took was enough to cause an electronic failure of the speed cycle control chip. Now Im waiting for that part. Read more...
Your Price
$32.82
  In Stock
SPRING
PartSelect Number PS2349237
Manufacturer Part Number 134616200
Your Price
$37.64
  On Order
Snubber Ring
PartSelect Number PS473378
Manufacturer Part Number 5308002385
The snubber ring on your washing machine mounts at the base, under the support. If you notice that your washing machine is vibrating, shaking, or moving during the wash cycle, you may need to replace the snubber ring. Because the snubber ring is located under the tub of the washing machine, you will need to remove the front panel to access it. To protect your hands when removing the snubber ring, consider using a bent coat hanger or a sturdy wire with a hook to pull the old snubber ring free. Be sure to disconnect the power and water sources for the washing machine before you begin this repair.
Fixes these symptoms
Installation Instructions
Steven from Jacksonville, IL
Worn belt, faulty snubber. Washing machine was 'walking' during spin cycle.
Unplugged machine.
Turned off water supply.

Removed front panel.
Pushed in on belt tensioner, removed old belt, replaced with new belt.

Used pry bar to lift the base assembly high enough off the snubber to remove it. Partially propped it with 2x4 wood scraps.

Used bent clothes hangar to remove old snubber ring, to protect my hands.

Replaced snubber, arrow pointing up.
Carefully lowered base assembly.

Replaced front panel.
Turned water back on, plugged back in, washing machine no longer 'walks'.

Remember to check the washer against a level if you moved the machine.
Read more...
Your Price
$155.00
  On Order
Shock Absorber Kit
PartSelect Number PS8689636
Manufacturer Part Number 5304491701
Your Price
$35.18
  In Stock
Tension Spring
PartSelect Number PS446551
Manufacturer Part Number 3204425
This tension spring works in conjunction with the idler pulley. The spring is part of your top load washing machine assembly. The most likely reasons for needing to replace the tension spring is if you notice that your washer is not spinning or agitating, the drive belt has come loose, and the idler pulley is no longer secure. To access this part, you will need to remove the front of your washer. The spring is located underneath the bottom of the tub. This is a genuine OEM part that comes right from the manufacturer.
Fixes these symptoms
Installation Instructions
garland from Morganton, NC
Washer wouldn't spin.
The problem with my very old washer was that the tension spring had broken long ago and I had jerry-rigged it in place with a cable tie. It would work, but you had to give the drum a spin by hand when it hit the spin the cycle. This probelm further caused the premature wearing of the drive belt, due to slippage. I ordered both a new spring and a new belt. Upon their arrival, I removed the two screws holding the front panel and lowered it off and out of the way. The old, worn belt was very easy to remove, as there was very little tension on it. Next I attempted to remove the washer that holds the idle arm on. It is in a very awkward spot, and it appears the the washing machine is sort of built around it. I bent it gradually with locking pliers until I could force it off with the blade of a flat screwdriver. Then the idler arm was easy to lower of its axle by twisting the drum a bit and pulling it to one side. I put the new spring into the idler arm, making sure the plastic bushing was in place and replaced the arm. I then repositioned to belt and replaced the front panel. It works great now. Read more...
Your Price
$22.33
  In Stock
Vertical Spring - Short
PartSelect Number PS1990844
Manufacturer Part Number 134886600
Sold individually.
Installation Instructions
Celeste from YAKIMA, WA
Washer tub enables after end of spin cycles
Replacing all springs. Able to replace 2 short springs and front spring. Can't get to ones in back of washer tub. Unable to use strenght in arms to remove old springs. Help videos were great. Saved money by doing repairs myself. Read more...
Your Price
$58.37
  Special Order
Suspension Spring
PartSelect Number PS975777
Manufacturer Part Number 134362800
Sold individually.
Fixes these symptoms
Your Price
$16.61
  In Stock
Suspension Spring - Long
PartSelect Number PS1990843
Manufacturer Part Number 134885900
Sold individually.
Installation Instructions
Celeste from YAKIMA, WA
Washer tub enables after end of spin cycles
Replacing all springs. Able to replace 2 short springs and front spring. Can't get to ones in back of washer tub. Unable to use strenght in arms to remove old springs. Help videos were great. Saved money by doing repairs myself. Read more...
Your Price
$32.23
  In Stock
Shock Absorber - Rear
PartSelect Number PS11765900
Manufacturer Part Number 137412601
Your Price
$42.37
  Special Order
Shock Absorber - Front
PartSelect Number PS11765901
Manufacturer Part Number 137412701

Related Parts