Dryer Fans and Blowers
Popular Dryer Fans and Blowers
Your Price
$22.86
In Stock
Dryer Blower Wheel with Clamp
PartSelect Number PS2200270
Manufacturer Part Number Y303836
This comes with a metallic hub clamp to hold it firmly in place. The blower wheel with clamp is part of your dryer assembly. You will find this part attached to the drive motor shaft, which disperses air through the drum and out of the exhaust vent. This part might need to be replaced if you notice your dryer is taking too long to dry clothing, it is not tumbling, or is making any unusually loud noises. The blower wheel measures about 7.5 inches in diameter by 3-3/8 wide. The blower wheel can be accessed by removing the front panel of your appliance.
Fixes these symptoms
- Noisy
- Too hot
- See more...
Installation Instructions
Stephen from Lafayette, IN
The blower fan (nylon) stripped off the motor shaft (steel)
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
Read more...
Your Price
$36.60
In Stock
Dryer Blower wheel
PartSelect Number PS11743785
Manufacturer Part Number WP694089
The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Daniel from Coatesville, PA
Bought motor, then bought blower wheel also
couldn't get blower wheel off of the motor. really tight. rounded off the wheel's square hub while trying to hold it still as I turned the motor shaft out. No, I wasn't turning it the wrong way :) I ended up going to the back of the dryer and using the multimax to quickly cut the wheel away from the hub. I love that oscillating saw! Just for fun, I put the motor in a bench vise and got the wheel hub off (in pieces). VERY tight! Ordered new wheel, and the job was smooth sailing from there on. I am guessing that experienced repair people automatically order the motor and blower wheel at the same time(?) BTW both parts were perfect matches for the originals. Not surprised; this has always been my experience with partselect.com!
Read more...
Your Price
$116.24
In Stock
Dryer Blower Housing with Blower Wheel
The top panel was easily taken off by removing 2-screws from the back edge of the panel, and sliding it back to release it from the front panel seam.
The front panel is more involved, but still relatively easy for your average "do-it-yourselfer". I removed the front door panel by first removing the control panel (4-screws; 2 on top and 2 from the back of the panel). I removed 2 cable assemblies from the control panel via connecters (different sizes so didn't need to mark) and 2-wires attached to the large control panel mode selector (I marked these 2-wires). I set aside the control panel. I removed the front door panel by taking off 6-screws (2 on top, 2 on the bottom, and the remaining 2 on the inside of the panel on either side of the drum). After removing these 6-screws, I carefully pulled the front door panel away from the front of the dryer, carefully releasing 4-alignment latches (2 on either side). The front door panel was still electrically attached to the machine so I had to disconnect a couple more wires. I carefully disconnected 2-wires from the door light assembly and 3 more wires from the door switch (I marked the 3-wires on the door switch). I set aside the front door panel.
From the back of the dryer, I removed the small motor access panel on the bottom left corner. This panel also provides access to the drum belt. I released the drum belt from the motor drive wheel by releasing spring tension at the tensioner. The belt can easily be disconnected from the motor drive wheel and tensioner assemblies.
Removal of the drum was now possible. With the front door panel removed, the front of the drum is maintained in place via a small plastic stop on the top crossmember. I removed this stop prior to removing the drum. With one hand, carefully grabbing the belt that is was loosely draped across the back of the drum, and the other hand holding the front lip of the drum, I provided a quick and forceful upward motion to the back of the drum in order to dislodge the drum shaft from the bearing housing assembly. Once this was accomplished, I simple pulled the drum out of the dryer housing via the front of the machine.
The drum bearing repair kit ordered came with the replacement ball bearing, bearing housing, drum shaft, high-temperature grease, and attaching hardware.
I replaced the drum shaft on the drum via the 4-screws accessed on the drum rear panel.
I removed the old bearing/bearing housing via the 2-screws holding it in place. I wasn't too concerned about loosing the small ball bearing as the kit provided me a new one. I generously applied some high-temperature grease to coat the interior lining of the new bearing housing. I also placed a dab on the back seat where the new ball bearing sits. This helped hold the bearing in place while reattaching it. I reinstalled the bearing housing to finish replacing the repair parts.
Reassembly of the drum is in the reverse order. I paid particular attention to making sure the new drum shaft properly seated with the new drum bearing housing.
After reinstalling the drum and while the front door panel was still off the dryer, it was easy to inspect the blower housing. I found the squirrel cage had broken loose from the molded nut that attaches it to the motor shaft. That would explain the heat problem; the heat was not being exhausted through the duct.
THE SQUIRREL CAGE IS REVERSE THREADED. I was unable to remove the nut from the motor shaft as the design encompasses a metal bushing molded into a plastic nut shaped form. The plastic would not hold up to the force I was applying trying to loosen the squirrel cage. So I ended up removing the entire motor and blower housing assembly from the base Read more...
PartSelect Number PS418726
Manufacturer Part Number 131775600
***Please Note: This part is a substituted part by the manufacturer. It may appear different, but should still work with your appliance.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Gerald from Cumming, GA
Had 2-seperate problems; 1st was a high pitch squeel, 2nd was the cover overheating
The high pitch squeel was the result of a failing drum bearing. It was particularly evident when first turning on the dryer, but became softer as the dryer heated up. In order to replace the drum bearing, I removed the top panel and front door panel.The top panel was easily taken off by removing 2-screws from the back edge of the panel, and sliding it back to release it from the front panel seam.
The front panel is more involved, but still relatively easy for your average "do-it-yourselfer". I removed the front door panel by first removing the control panel (4-screws; 2 on top and 2 from the back of the panel). I removed 2 cable assemblies from the control panel via connecters (different sizes so didn't need to mark) and 2-wires attached to the large control panel mode selector (I marked these 2-wires). I set aside the control panel. I removed the front door panel by taking off 6-screws (2 on top, 2 on the bottom, and the remaining 2 on the inside of the panel on either side of the drum). After removing these 6-screws, I carefully pulled the front door panel away from the front of the dryer, carefully releasing 4-alignment latches (2 on either side). The front door panel was still electrically attached to the machine so I had to disconnect a couple more wires. I carefully disconnected 2-wires from the door light assembly and 3 more wires from the door switch (I marked the 3-wires on the door switch). I set aside the front door panel.
From the back of the dryer, I removed the small motor access panel on the bottom left corner. This panel also provides access to the drum belt. I released the drum belt from the motor drive wheel by releasing spring tension at the tensioner. The belt can easily be disconnected from the motor drive wheel and tensioner assemblies.
Removal of the drum was now possible. With the front door panel removed, the front of the drum is maintained in place via a small plastic stop on the top crossmember. I removed this stop prior to removing the drum. With one hand, carefully grabbing the belt that is was loosely draped across the back of the drum, and the other hand holding the front lip of the drum, I provided a quick and forceful upward motion to the back of the drum in order to dislodge the drum shaft from the bearing housing assembly. Once this was accomplished, I simple pulled the drum out of the dryer housing via the front of the machine.
The drum bearing repair kit ordered came with the replacement ball bearing, bearing housing, drum shaft, high-temperature grease, and attaching hardware.
I replaced the drum shaft on the drum via the 4-screws accessed on the drum rear panel.
I removed the old bearing/bearing housing via the 2-screws holding it in place. I wasn't too concerned about loosing the small ball bearing as the kit provided me a new one. I generously applied some high-temperature grease to coat the interior lining of the new bearing housing. I also placed a dab on the back seat where the new ball bearing sits. This helped hold the bearing in place while reattaching it. I reinstalled the bearing housing to finish replacing the repair parts.
Reassembly of the drum is in the reverse order. I paid particular attention to making sure the new drum shaft properly seated with the new drum bearing housing.
After reinstalling the drum and while the front door panel was still off the dryer, it was easy to inspect the blower housing. I found the squirrel cage had broken loose from the molded nut that attaches it to the motor shaft. That would explain the heat problem; the heat was not being exhausted through the duct.
THE SQUIRREL CAGE IS REVERSE THREADED. I was unable to remove the nut from the motor shaft as the design encompasses a metal bushing molded into a plastic nut shaped form. The plastic would not hold up to the force I was applying trying to loosen the squirrel cage. So I ended up removing the entire motor and blower housing assembly from the base Read more...
Your Price
$55.40
In Stock
Dryer Blower Wheel
PartSelect Number PS11743811
Manufacturer Part Number WP697772
The blower wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. The blower wheel, which is usually plastic, may wear out over time. But if it's noisy, it may simply be clogged with lint. Clean the blower and test to see if the dryer is still noisy. If it is, you probably need to replace it.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
joe from cheswick, PA
craked blower motor
somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme
Read more...
Dryer Blower Wheel and Housing
Parts select. The hardest part was getting a spring that holds the tensioner on the drum belt. Read more...
PartSelect Number PS2349262
Manufacturer Part Number 134690800
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Harry from Republic, PA
The blower housing was cracked
I used utube on how to dismantle the dryer. In fact I use a video created by Parts select. The hardest part was getting a spring that holds the tensioner on the drum belt. Read more...
Your Price
$43.98
In Stock
Dryer Blower Wheel
PartSelect Number PS2035614
Manufacturer Part Number 33001790
This blower wheel does not come with a spring clamp, but it does have twenty fins and it is designed to fit a 3/8 of an inch motor shaft.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Terry from Caruthersville, MO
loud noise inside dryer
After changing all the rollers in the dryer (which didn't fix the problem) I decided to take apart the blower. Sure enough, that was the problem. As the dryer heated up, the damaged wheel would swell and start rubbing the housing. I replaced both and fixed the problem. The repair was pretty easy, since I had taken the dryer apart several times replacing the rollers.
Read more...
Dryer Blower Housing
PartSelect Number PS8689120
Manufacturer Part Number 137551110
This blower housing is for dryers.
Blower housing covers and protects the blower fan wheel, and helps direct the flow of air through the dryer.
Unplug the dryer before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
- Noisy
- See more...
Dryer Blower Wheel
PartSelect Number PS11753413
Manufacturer Part Number WPW10349492
The blower wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct.
Fixes these symptoms
- Noisy
- See more...
Your Price
$64.21
In Stock
Dryer Blower Wheel
PartSelect Number PS2052494
Manufacturer Part Number 56000
If your dryer is noisy, will not tumble, or is not producing enough heat, you may need to replace the blower wheel. This part is white in color, and is made of plastic. This part is approximately 8 inches in diameter. The blower wheel is located near the bottom of your dryer cabinet. To access it for this repair, you will need to remove both the front panel and the front bulkhead assembly. Before you begin this repair, be sure to disconnect the power source to the dryer. To complete this repair, you will need a 5/16 inch nut driver, a 1/4 inch nut driver, a pair of locking pliers and a 7/8 socket with a short extension and a ratchet.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Rick from Birch Run, MI
Blower fan cracked
Unplug the power cord from the unit. Remove the lower front panel; then the upper front panel including the door (unplug wire to door switch). Then remove the cover on the fan housing. Need to block the motor from turning; I used a stick to jamb the front of the motor; then unscrew the old blower fan and screw on the new one. Then replace the cover and put front panels back on.
Read more...
Dryer Blower Wheel and Housing Assembly
PartSelect Number PS8770136
Manufacturer Part Number 137552300
The blower wheel and housing assembly spins on the motor shaft to blow air through the dryer drum and out through the exhaust.