Dryer Drums and Tubs
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Dryer Drums and Tubs
Your Price
$13.58
In Stock
Dryer Front Glide Kit
2. Removed 4 screws from inside the dryer, to take off the blower housing.
3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum.
4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they run on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings.
5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits.
6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together.
7. Replaced the felt blower seal. Glued to the blower housing.
8. Reinstalled the drum, installed new belt, which came with good instructions (luckily).
9. Reassembled front support piece and the front of the cabinet.
I also cleaned the lint from the cabinet and from the vent hose.
In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.
I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine. Read more...
PartSelect Number PS1804752
Manufacturer Part Number 306508
The front glide is located at the front of the dryer, the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and require replacing. This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. While you have the front bulkhead removed for this repair, you may want to inspect the felt that lines it. If the felt is damaged, it is recommended that you replace it at the same time. You will need a rivet tool for this installation, as well as a stubby Phillips screwdriver, a 5/16 nut driver, and a drill with a 1/8-inch bit.
Fixes these symptoms
- Drum Not Spinning
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
John from Charlottesville, VA
Belt broke on old machine.
1. Removed front of machine (2 screws at the bottom).2. Removed 4 screws from inside the dryer, to take off the blower housing.
3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum.
4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they run on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings.
5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits.
6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together.
7. Replaced the felt blower seal. Glued to the blower housing.
8. Reinstalled the drum, installed new belt, which came with good instructions (luckily).
9. Reassembled front support piece and the front of the cabinet.
I also cleaned the lint from the cabinet and from the vent hose.
In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.
I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine. Read more...
Your Price
$24.95
In Stock
Dryer Drum Glide - White
PartSelect Number PS5574052
Manufacturer Part Number 137513300
This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there are two of these in your appliance. We recommend that these be replaced at the same time, this allows for optimal performance and ensures they wear evenly. Each drum glide is approximately 33 inches in length. If the following symptoms occur, consider replacing the drum guide as a solution: dryer is noisy, will not tumble, or leaves marks on clothes. Remember to unplug the power source to the dryer before installing this part. Refer to the diagram provided by the manufacturer for further instructions and guidance.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Sergio from Cromwell, CT
Clothes were getting caught in gap, leaving burn mark.
Took the face off, and replaced the worn down drum glide and felt. Works just fine now.
Read more...
Your Price
$11.95
Special Order
Dryer Drum Glide
PartSelect Number PS11741931
Manufacturer Part Number WP37001298
If your dryer is noisy, will not tumble, or is leaving marks on your clothes, you may need to replace the drum glide. The drum glide is installed on the front bulkhead either at the top or the bottom, regardless of the brand of dryer. To gain access to the drum glide, you will have to open the cabinet on the dryer. This drum glide is sold individually but it is important to note that they should be replaced in pairs. Before beginning this repair, it is important to disconnect the dryer from the power source. The tools required for this repair are a putty knife and a 5/16 nut driver.
Fixes these symptoms
- Drum Not Spinning
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
David from Underwood, IA
Loud banging sound. Worn out roller.
Pulled off the lower panel with 5/16 socket.Pulled off the door assembly by removing the two screws at the bottom of the door assembly. I pulled down a little and then out. be carefull of the wires. Other posts said to remove. The wires were long enough I did not have to remove them. I just leaned it against the wall. I then removed the 4 screws that hold the front piece in.pulled it off replaced brackets , installed self adhesive felt(stuck good) and then glides. Mine were thin but not the problem. I then reached under the drum and released the belt from the tensioner. I then pulled the whole drum out.This is the time to vacum out good. I could get to the rear rollers very easy. The left roller was shot and the shaft half wore into(the problem). I pulled off the two screws holding the roller support. Normally You have to remove the wheel with snap ring pliers first to remove the support. In this case snap ring long gone. Replaced support shaft, installed thrust washers and roller with grease for both sides. The right support shaft was still good. Removed tensioner pulley and inspected. It was just as good as the new one. Cleaned and greased and reinstalled. Put new belt on the tub and slid it back in. Be carefull to get the belt on the proper side of the tensioner. I then installed the front supprt in place to support the tub with the 4 screws. Spun the tub(felt good) then reached under and reinstalled belt to motor and tensioner. Spun again to check for belt alignment. (Check) Reinstalled door an lower panel. Test Quiet Sounds like new. Very easy! I hope this helps someone just as the other post has helped me. Blessings to all.
Read more...
Your Price
$28.87
In Stock
Dryer Tall Baffle
PartSelect Number PS11741085
Manufacturer Part Number WP33002032
This part moves the clothes around inside your dryer and helps to direct the flow of hot air during the drying cycle.
NOTE: Screws are NOT included.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Teresa from Pace, FL
dried too many shoes and broke the baffles
removed door, removed screws to lift top panel, removed screws that held old baffles, replaced with new baffles, took off front panel and cleaned out excess lint while I was in there.
Read more...
Your Price
$36.95
In Stock
Dryer Drum Baffle
PartSelect Number PS12743402
Manufacturer Part Number WE13X29725
This dryer drum baffle is a durable internal component designed to enhance drying performance by lifting and separating laundry as the drum rotates. Its function is to promote even tumbling and improved air circulation, preventing clothes from clumping or tangling during the drying cycle. Constructed from high-quality materials to withstand high temperatures and frequent use, the baffle contributes to energy efficiency and consistent drying results. Replacing a worn or damaged baffle can restore optimal airflow, reduce drying time, and extend the life of the appliance. Installation typically involves accessing the drum interior and securing the baffle with appropriate fasteners. Compatible with select dryer models, this part ensures reliable performance and efficient operation.
Your Price
$31.86
In Stock
Dryer Short Baffle
PartSelect Number PS11741064
Manufacturer Part Number WP33001755
This part moves the clothes around inside your dryer and helps to direct the flow of hot air during the drying cycle.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Teresa from Pace, FL
dried too many shoes and broke the baffles
removed door, removed screws to lift top panel, removed screws that held old baffles, replaced with new baffles, took off front panel and cleaned out excess lint while I was in there.
Read more...
Your Price
$14.95
In Stock
Dryer Top Bearing Felt
PartSelect Number PS2355953
Manufacturer Part Number WE9M31
This felt attaches to the top bearing.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
michael from WELLINGTON, FL
The dryer was squeaking loudly
I looked on you tube and was able to determine the cause and order the parts I needed to rectify the issue. I removed the the top panel and the front panel. I replaced the bearing.
Read more...
Your Price
$44.95
On Order
Dryer Baffle
PartSelect Number PS3522961
Manufacturer Part Number 4432EL1002A
Designed exclusively for your LG dryer, the Drum Baffle - Lifter is a premium, OEM (Original Equipment Manufacturer) component guaranteed for an exact fit and superior performance. This drum baffle lifts and tumbles clothing within the drum during the drying cycle, contributing to efficient and thorough drying. Always remember to unplug your dryer before proceeding with the installation of this component. Also, always wear work gloves to provide protection for your hands while installing. Consult your model's manual to ensure this is the correct component for your dryer - as parts might visually appear the same, but might have small size and shape variations. Trust in the quality, durability, and reliability that LG provides with every component.
Your Price
$48.95
In Stock
Dryer Cylinder Glide Bracket
2) Removed door
3) Removed Front Panel - removed connectors from switch and marked connections
4) Removed Front Bulkhead
5) Glides and Felt pads were missing, and brackets were nearly worn through
6) Removed and Replaced old brackets
7) Attached self-adhesive felt pads
8) Attached Drum Glides
9) Removed old felt seal
10) Glued new felt seal in place with 5-min epoxy
11) Allowed Epoxy to set and stop stinking
12) Re-attached front bulkhead
13) Re-attached remaining parts
Dryer works great, is quiet again, and no longer eats clothes!!!!!! Read more...
PartSelect Number PS11741912
Manufacturer Part Number WP37001036
These brackets support each side of the tub. Order quantity needed.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Jeffrey from Medina, OH
Noisy - Clothes getting stuck between drum and bulkhead
1) Removed lower panel2) Removed door
3) Removed Front Panel - removed connectors from switch and marked connections
4) Removed Front Bulkhead
5) Glides and Felt pads were missing, and brackets were nearly worn through
6) Removed and Replaced old brackets
7) Attached self-adhesive felt pads
8) Attached Drum Glides
9) Removed old felt seal
10) Glued new felt seal in place with 5-min epoxy
11) Allowed Epoxy to set and stop stinking
12) Re-attached front bulkhead
13) Re-attached remaining parts
Dryer works great, is quiet again, and no longer eats clothes!!!!!! Read more...
Your Price
$355.95
On Order
Dryer Drum Wrapper Assembly
https://www.youtube.com/watch?v=9ul2BIvVEVU&t=428s
Once the new drum was installed, I followed the steps in reverse to put everything back together. Read more...
PartSelect Number PS17504197
Manufacturer Part Number DC97-23529E
Introducing an authentic Drum Wrapper Assembly Module, exclusively manufactured by Samsung. This original OEM item delivers the trusted durability and performance Samsung is known for. Ideal for repairing and upgrading your appliances, its unique design caters to a variety of models. However, be sure to cross-reference your model before proceeding with the purchase as there can be minor differences in size and shape between parts. This high-quality Drum Wrapper Assembly is crafted to perfectly fit and function with your Samsung appliances, ensuring a long and dependable operational life.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Brendan from CASPER, WY
The drum wrapper on our dryer was coming apart in the back, causing the metal drum to tear apart and causing the drum to not roll properly.
I had to take the whole thing apart to replace the drum wrapper. I followed this very helpful YouTube video for the step-by-step instructions on disassembly.https://www.youtube.com/watch?v=9ul2BIvVEVU&t=428s
Once the new drum was installed, I followed the steps in reverse to put everything back together. Read more...
Dryer Drum or Tub Brands
- Admiral Dryer Drums and Tubs
- Amana Dryer Drums and Tubs
- Crosley Dryer Drums and Tubs
- Estate Dryer Drums and Tubs
- Frigidaire Dryer Drums and Tubs
- General Electric Dryer Drums and Tubs
- Inglis Dryer Drums and Tubs
- Kenmore Dryer Drums and Tubs
- KitchenAid Dryer Drums and Tubs
- LG Dryer Drums and Tubs
- Magic Chef Dryer Drums and Tubs
- Maytag Dryer Drums and Tubs
- Roper Dryer Drums and Tubs
- Samsung Dryer Drums and Tubs
- Whirlpool Dryer Drums and Tubs