Dryer Drawers and Glides
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Dryer Drawers and Glides
Your Price
$14.65
In Stock
Dryer Front Glide Kit
2. Removed 4 screws from inside the dryer, to take off the blower housing.
3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum.
4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they run on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings.
5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits.
6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together.
7. Replaced the felt blower seal. Glued to the blower housing.
8. Reinstalled the drum, installed new belt, which came with good instructions (luckily).
9. Reassembled front support piece and the front of the cabinet.
I also cleaned the lint from the cabinet and from the vent hose.
In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.
I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine. Read more...
PartSelect Number PS1804752
Manufacturer Part Number 306508
The front glide is located at the front of the dryer, the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and require replacing. This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. While you have the front bulkhead removed for this repair, you may want to inspect the felt that lines it. If the felt is damaged, it is recommended that you replace it at the same time. You will need a rivet tool for this installation, as well as a stubby Phillips screwdriver, a 5/16 nut driver, and a drill with a 1/8-inch bit.
Fixes these symptoms
- Drum Not Spinning
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
John from Charlottesville, VA
Belt broke on old machine.
1. Removed front of machine (2 screws at the bottom).2. Removed 4 screws from inside the dryer, to take off the blower housing.
3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum.
4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they run on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings.
5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits.
6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together.
7. Replaced the felt blower seal. Glued to the blower housing.
8. Reinstalled the drum, installed new belt, which came with good instructions (luckily).
9. Reassembled front support piece and the front of the cabinet.
I also cleaned the lint from the cabinet and from the vent hose.
In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.
I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine. Read more...
Your Price
$34.77
On Order
Dryer Upper Drum Glide
What I would add to previous reviews is to pull the front off or the little acces grill in back and check to see what kind of belt you have. According to the model #, It showed the wide flat belt when in fact I had the smaller ribbed belt. Glad I checked before ordering.
A few things that will make your life easier is once you have the old upper guide/seal removed, put down the glue then use several med sized plastic spring clamps to hold the seal in place while the glue sets up, (@ 20-30 min). Their cheap and you should have some around anyway. When replacing the seals I would go ahead and replace the belt too. It's cheap and if your machine is 5+ yrs old probably is worn. Total cost of repair was about $60 (inc shipping). Took about 1 hr 20 min total time. Most of that time was scrapping the old seal material/ glue off the dryer front. Actual disassembly and repair maybe 1/2 hour. Other little tip is the clips for the lid of dryer is to use a flat screwdriver and gently push straight in until it's compressed enough to release the lid, it will pop up when pushed in far enough. That one took me a while to figure out.
Thanks to Part Select for such a helpful site. My dryer is like new again. Read more...
PartSelect Number PS470317
Manufacturer Part Number 5303937139
The upper drum glide is attached to the front panel of your dryer, you can locate it by removing the top portion of your dryer. The drum glide allows the drum to rotate with ease and little sound. The front upper felt glide pad with three nylon glides also includes adhesive, essential for mounting accurately. For this project you will need a putty knife, Phillips screwdriver, and a wire brush. This repair is meant to fix issues such as an abnormal amount of noise or the dryer not tumbling as it should. Consider replacing your belt at the same time if you have a dryer more than 5 years old, as it is likely worn.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Matthew from Portland, OR
Clothes getting scorch marks, drum noise
First and foremost, I read the repair reviews here at parts source and found that a) Other people had the same symptoms, b)following their repair tips made it super easy.What I would add to previous reviews is to pull the front off or the little acces grill in back and check to see what kind of belt you have. According to the model #, It showed the wide flat belt when in fact I had the smaller ribbed belt. Glad I checked before ordering.
A few things that will make your life easier is once you have the old upper guide/seal removed, put down the glue then use several med sized plastic spring clamps to hold the seal in place while the glue sets up, (@ 20-30 min). Their cheap and you should have some around anyway. When replacing the seals I would go ahead and replace the belt too. It's cheap and if your machine is 5+ yrs old probably is worn. Total cost of repair was about $60 (inc shipping). Took about 1 hr 20 min total time. Most of that time was scrapping the old seal material/ glue off the dryer front. Actual disassembly and repair maybe 1/2 hour. Other little tip is the clips for the lid of dryer is to use a flat screwdriver and gently push straight in until it's compressed enough to release the lid, it will pop up when pushed in far enough. That one took me a while to figure out.
Thanks to Part Select for such a helpful site. My dryer is like new again. Read more...
Your Price
$20.96
In Stock
Dryer Drum Slide
2. Using phillips head screwdriver. Removed two screws holding down top of machine.
3. Swung machine top lid back.
4. Disconnect two wires from door switch.
5. Using socket wrench removed two hex head machine screws holding front panel onto machine.
6. While reaching in through door to hold drum, Swung entire front panel down and away from machine and carefully rested drum on frame.
7. Using flat head screwdriver, pryed worn drum bearing off of front panel.
8. Removed Support Spanner (white flexible plastic piece approx 8" x 2") from old drum bearing and put on new drum bearing.
9. Put new teflon drum slides (this model takes 3) on replacement drum bearings.
10. Snapped new drum bearing in place on front panel.
11. Reverse step 1-6 above.
TIME: APPROX 20-30 MINUTES. Read more...
PartSelect Number PS267877
Manufacturer Part Number WE3X87
This slide is sold individually. Some dryers require up to three of these slides . Be sure to check to make sure you order the necessary amount for your dryer.
Fixes these symptoms
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
Henery from Ramsey, NJ
Loud scraping noise when drum rotated
1. Opened door.2. Using phillips head screwdriver. Removed two screws holding down top of machine.
3. Swung machine top lid back.
4. Disconnect two wires from door switch.
5. Using socket wrench removed two hex head machine screws holding front panel onto machine.
6. While reaching in through door to hold drum, Swung entire front panel down and away from machine and carefully rested drum on frame.
7. Using flat head screwdriver, pryed worn drum bearing off of front panel.
8. Removed Support Spanner (white flexible plastic piece approx 8" x 2") from old drum bearing and put on new drum bearing.
9. Put new teflon drum slides (this model takes 3) on replacement drum bearings.
10. Snapped new drum bearing in place on front panel.
11. Reverse step 1-6 above.
TIME: APPROX 20-30 MINUTES. Read more...
Your Price
$84.84
In Stock
Dryer Front Glide Kit
PartSelect Number PS2003584
Manufacturer Part Number 12002126
This kit includes 2 glides (left and right), 2 pads with adhesive backing and 1 support brace.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Thomas from Oneonta, NY
Dryer made a loud noise and vibrated badly
First I made sure the unit was unplugged. I popped the top of the unit with a slotted screw driver, lifted the top up and rested it against the wall behind the dryer. I removed the two screws - one on each side in front on top of the dryer cabinet. Then I tipped back the front panel of the dryer slightly with the door of the dryer closed. I unclipped the door switch with a slotted screw driver and then lifted the entire front panel including the door off of the the two floor clips on bottom. I set the front panel aside. Next I lifted the large drum slightly to dislodge the rollers in back and slid the drum back slowly while sliding the thin belt back on the drum until the drum was out of the unit and the belt was detached and loose. Then I cleaned the unit thoroughly, vacuumed all lint and dirt and wiped down the outside of the large drum with mineral spirits to make sure it was totally clean and smooth. Then I removed the two rollers and the roller shafts at the back of the unit following the directions enclosed. My slip-ring pliers came in handy to remove the retaining rings on the roller shafts. I replaced the rollers and roller shafts and the supplied washers and spacers as per the instructions. I sprayed a little WD-40 on the surface of the rollers and it stopped all squeaking and vibration of the drum. Next I replaced the front drum pads and runners as per the instructions. I then slid the drum back in place taking care to slide the new belt back around the drum in the same position as the old belt. Now came the difficult part - laying on the floor and reaching under the drum I positioned the belt around the motor shaft and tension pulley. This must be done by "feel" and must be done correctly!! Follow the instructions on the positioning of the belt very carefully and make sure it is in the correct position on the drum, motor shaft, and tension pulley! Next, get up and rock the drum up and down slightly to make sure it has engaged the two rear rollers properly. Rotate the drum manually one or two turns to make sure the belt is in the correct position. Then replace the front door panel by dropping it onto the two clips at the base of the unit and taking care to replace the door switch in reverse order of taking it out. Then replace the two screws at the top front on each side of the unit to secure the front panel. Lower the top of the unit back in place, plug in the dryer, turn it on and enjoy the lack of noise you have created.
Read more...
Your Price
$104.54
In Stock
Dryer Drawer Slider - Right Side
PartSelect Number PS3522885
Manufacturer Part Number 4276ER0001A
Installation Instructions
Marcelo from LUTZ, FL
Drawer had broken rail. Would not stay closed.
Removed drawer, unscrewed right side rail and replaced it with new rail. I used only a Phillips head screw driver. Warning: when ordering the rails, be aware, the rail labeled for the right side of the drawer actually goes on the left and vise versa. Luckily I ordered one of each and decided to replace both rails. The right one broke first and the left one broke as I removed it
Read more...
Your Price
$104.54
In Stock
Dryer Drawer Slider - Left Side
PartSelect Number PS3522886
Manufacturer Part Number 4276ER0002A
Installation Instructions
Paul from Georgetown, TX
Drawer under washer was frozen, would not move
Forced the drawer open and removed it, 4 screws. Found bearings on on one side severely corroded and locked up. Only hard part was determining which side it was. Ordered the left, my left looking at the washer. Wrong!it was the washers right looking back at me.
Read more...
Your Price
$45.27
In Stock
Dryer Drum Glide - Left Side
PartSelect Number PS11740714
Manufacturer Part Number WP31001470
This dryer drum glide is almost six inches long and is blue in color. This glide is made of plastic and is designated for the left side of some clothes dryers. This glide is also available as part of a glide kit, part number PS177273.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Greg from Salt Lake City, UT
Dryer made noises like metal on metal grinding
Unplugged the dryer then popped the top off and tilted it back, exposing the drum. Then using a flat bladed screw driver, removed the two sheet metal screws holding the front panel on. Once the front panel was removed, I pulled the drum off, exposing the motor and worn pulley. I removed the pulley arm, then removed the pulley. The bearings were totally gone, so I replaced it with a new pulley, replaced the belt and the front drum glides, since they were obviously worn. While it was apart, I cleaned out the interior with a shop vac, which greatly improved the efficiency of the dryer.
Read more...
Your Price
$58.84
In Stock
Dryer Slide
PartSelect Number PS11746770
Manufacturer Part Number WP8578394
Installation Instructions
Donald from Greenfield, WI
Bent slide on pedestal
Note that the problem was with the pedestal, not the washing machine. In the process of attaching the two units together, the drawer in the pedestal is removed. When I tipped the assembly up, the slide slid out and locked horns with an object, bending the slide. The slide is an easy replacement. Just one screw holds it in place. A slot in the slide mates with a tab to hold the back side of the slide in place.
Read more...
Your Price
$77.34
In Stock
Your Price
$57.72
Special Order
Dryer Drum Glide - Right Side
PartSelect Number PS11740713
Manufacturer Part Number WP31001469
This dryer drum glide is just under seven inches long. It is all blue in color and is made of a hard plastic. This front drum support is intended for use with the right side of clothes dryers.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Greg from Salt Lake City, UT
Dryer made noises like metal on metal grinding
Unplugged the dryer then popped the top off and tilted it back, exposing the drum. Then using a flat bladed screw driver, removed the two sheet metal screws holding the front panel on. Once the front panel was removed, I pulled the drum off, exposing the motor and worn pulley. I removed the pulley arm, then removed the pulley. The bearings were totally gone, so I replaced it with a new pulley, replaced the belt and the front drum glides, since they were obviously worn. While it was apart, I cleaned out the interior with a shop vac, which greatly improved the efficiency of the dryer.
Read more...