Dishwasher Wheels and Rollers
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Dishwasher Wheels and Rollers
Your Price
$33.48
In Stock
Dishwasher Lower Dishrack Wheel
PartSelect Number PS3406971
Manufacturer Part Number W10195416
This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult. This can happen due to normal wear and tear, and the part should be replaced if this occurs. Check your model number and user manual to make sure this part is correct. It attaches directly to the dishrack. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel. It measures roughly 3x6 inches.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Thomas from WEST OLIVE, MI
Broken wheel unit on the bottom dish rack
All you do is pop out the old wheel unit at two (2) points on the plastic wheel housing and pop in the new one. Easy fix. Less than a 5 minute fix.
Read more...
Your Price
$46.02
In Stock
Dishwasher Lower Dishrack Wheel Assembly
PartSelect Number PS11750057
Manufacturer Part Number WPW10195417
This gray plastic lower dishrack roller is a part for your dishwasher. It attaches to the bottom of the lower dishrack, allowing it to move in and out smoothly. If the lower dishrack stops moving in and out easily or preventing you from being able to shut the dishwasher door, inspect the dishrack roller for damage. The assembly includes 2 rollers and the bracket that attaches to the dishrack (parts are not sold separately). This assembly is sold individually, so you will need 4 assemblies to replace them all in your appliance. For this easy repair, start by removing the lower dishrack from the appliance and set it on the counter. Use a screwdriver to pry off the old roller assembly from the lower tabs. Align the new part on the dishrack by snapping it in place.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Not cleaning dishes properly
- See more...
Installation Instructions
Barbara from BETHESDA, MD
One of the rollers broke of on the lower dish rack
Snapped the old one off and snapped the new one on.
Read more...
Your Price
$13.12
In Stock
Dishwasher Dishrack Roller - Grey
PartSelect Number PS8727387
Manufacturer Part Number 00611475
This dishrack roller is a genuine replacement part designed for the lower rack of select dishwashers. Made from durable gray plastic and measuring slightly over one inch in diameter, it features an integrated clip for secure attachment to the rack. The roller allows the lower dishrack to glide smoothly in and out of the dishwasher, supporting efficient loading and unloading. If a roller is broken or missing, the rack may become unstable or difficult to move. This OEM component is sold individually and installs easily by snapping it into place—no tools required. Regular replacement of worn rollers helps maintain optimal dishwasher performance.
Fixes these symptoms
- Door won’t close
- See more...
Installation Instructions
Dennis from PLEASANTVILLE, NJ
Your Price
$23.01
In Stock
Dishwasher Dishrack Adjuster And Wheel Assembly
PartSelect Number PS11756470
Manufacturer Part Number WPW10571738
This dishrack adjuster and wheel assembly is for dishwashers and lets you adjust the dishrack height and attaches the track wheels to the dishrack.
Fixes these symptoms
- Not cleaning dishes properly
- See more...
Installation Instructions
Alfred L from WESTBOROUGH, MA
The wheels on the bottom ‘basket’ are only fastened by a ‘Snap-in’ (plug) style connector that gets brittle and breaks over time
Pop off the shell assembly from the bottom basket and clip/click on a new wheel assembly.
Read more...
Your Price
$6.93
In Stock
Dishwasher Upper Wheel And Bushing Assembly (black)
1. Removed stops on front end of Upper Dishrack Slide on both sides.
2. Removed Upper Dishrack
3. Remove Roller and Axle/clip (4 each)
4. Push Roller onto Axle on all 4 kits
5. Install all 4 roller kits on Upper Dishrack
6. Remove stops from back end of Upper Dishrack Slides.
7. Remove both Slides
8. Remove 8 each Tub Wheels.
9. Using old or new Screws and Washers, install new Tub Wheels.
10. Install both Upper Dishrack Slides ensuring that small holes are toward the back.
11. Install stops on the back end of Slides.
12 Install Upper Dishrackinto slides
13. Install front stops on slide
14. Pulled out Gasket
15. Install replaced Gasket Read more...
PartSelect Number PS17219660
Manufacturer Part Number 5304535381
The upper dishrack roller and axel kit comes with two pieces, a wheel and an axle. This kit is made for your dishwasher. Both pieces measure to be roughly one square inch each, they are made entirely of plastic, and are white in color. The purpose of these parts is to allow your dishrack to roll easily on the support rails. This kit is sold individually and contains only one wheel and one axle. Please order the required quantity for your repair. If your dishrack is having trouble rolling in and out you may need replace your rollers and axles.
Installation Instructions
Terry from Pleasant View, UT
Top rack was dropping out of rollers/Slides
This was the second part of repair. Left side was constantly falling out of the slide. I replaced the same items as above minus the gasket and screw kit. Once done, the right side was sloppy so I orders part for that side plus gasket which slid right in. 1. Removed stops on front end of Upper Dishrack Slide on both sides.
2. Removed Upper Dishrack
3. Remove Roller and Axle/clip (4 each)
4. Push Roller onto Axle on all 4 kits
5. Install all 4 roller kits on Upper Dishrack
6. Remove stops from back end of Upper Dishrack Slides.
7. Remove both Slides
8. Remove 8 each Tub Wheels.
9. Using old or new Screws and Washers, install new Tub Wheels.
10. Install both Upper Dishrack Slides ensuring that small holes are toward the back.
11. Install stops on the back end of Slides.
12 Install Upper Dishrackinto slides
13. Install front stops on slide
14. Pulled out Gasket
15. Install replaced Gasket Read more...
Your Price
$12.91
In Stock
Dishwasher Lower Rack Roller
PartSelect Number PS16217024
Manufacturer Part Number WD12X26146
This lower rack roller is a genuine replacement component designed to support the smooth and stable movement of the dishwasher’s bottom rack. Measuring approximately 1.5 inches in diameter and finished in charcoal gray, it ensures consistent rack alignment and ease of use during loading and unloading. For optimal performance, it is recommended to replace all four rollers simultaneously. Installation is straightforward and requires no special tools, though wearing protective gloves is advised. Sold individually.
Installation Instructions
Dennis from CICERO, IN
Your Price
$10.92
In Stock
Dishwasher Wheel & Bushing Assembly
PartSelect Number PS16745479
Manufacturer Part Number 5304532229
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, or you notice that your dishwasher is not cleaning dishes properly, you may need to replace the rack wheel. The single rack roller kit is made of white plastic, and clips to the dishwasher rack with the included axle/clip. Many of our customers have described this repair as easy, and you will not require any tools to complete it.
Lower rack roller and bracket assembly, grey. Wheel has been updated. If wheel pictured is not like old one, you may need to replace all wheels.
Fixes these symptoms
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
CHRIS from ROANOKE, VA
Water leaking from Inlet Valve
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it leaked in the first place and messed up my subfloor and laminate flooring.
Read more...
Your Price
$34.85
In Stock
Dishwasher Rack Carrier And Roller Kit
PartSelect Number PS17873321
Manufacturer Part Number WD01X35298
- Includes: 4 brackets, 4 roller wheel brackets, and 8 wheels part # WD12X26146
Dishwasher Lower Dishrack Carrier and Roller Kit (Set of 4). This kit will replace all four one piece roller carriers with two piece roller carriers. Match each carrier and cover designated for the side being replaced and replace all four carriers
Fixes these symptoms
- Not cleaning dishes properly
- See more...
Installation Instructions
Teri from LAGUNA NIGUEL, CA
order #16343054 Complete service rack
this was ordered 4-9-21 and I have yet to receive it. Its difficult to explain the installation when you haven't received the main part. I paid for this but you have not shipped it. Very poor customer service.
Read more...
Your Price
$13.71
In Stock
Dishwasher Roller Assembly
PartSelect Number PS12075858
Manufacturer Part Number 4581DD3003C
The dishwasher roller assembly connects to the dishrack, and is located in the lower level of the dishwasher. It allows the dishrack to easily slide in and out. If the lower rack keeps falling off the track in your dishwasher, makes noises, the door will not close, or the dishes are not getting clean, then it is best to replace it for more security. A flat blade screw driver is the only tool needed for this installation. Open the lower dishwasher rack and remove retaining tabs from both ends of the rack and slide it out. Locate the older roll assembly, remove it and replace the rollers. Remember to put the tabs on each side back before sliding it back in. Make sure the dishwasher is off before starting this installation project.
Installation Instructions
Lenny from KIRTLAND, OH
Second roller in on the left side was missing don't ask my how, pulling the bottom rack out the rack would dip down i had to lift it up to pull it the rest of the way out.
Ordered the roller from Parts Select, slid the roller over the little spindle sticking out of the bottom rack and snapped it in place. Job done in less than one minute.
Read more...
Your Price
$26.87
In Stock
Dishwasher Upper Dish Rack Wheel Mount
PartSelect Number PS11745459
Manufacturer Part Number WP8268743
This upper dish rack wheel mount can be used on either side of your dish rack. It is sold individually. The part includes the wheel and support, which attaches to the dish rack and allows it to slide in and out easily.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Noisy
- See more...
Installation Instructions
Jason from Todd, NC
Worn dishrack wheel mount
This wheel mount broke from normal use and made the upper dish rack disconnect from the sliding arm that extends it outside the dishwasher body so that you can fill it. The part was delivered quickly and was easy to install using just a screwdriver to loosen the retainer clip on the end of the extension slide. Once the retainer clip was removed, the new part was slid into place and clipped onto the rack. The install was complete.
Read more...
Dishwasher Wheel or Roller Brands
- Admiral Dishwasher Wheels and Rollers
- Amana Dishwasher Wheels and Rollers
- Crosley Dishwasher Wheels and Rollers
- Frigidaire Dishwasher Wheels and Rollers
- General Electric Dishwasher Wheels and Rollers
- Gibson Dishwasher Wheels and Rollers
- Hotpoint Dishwasher Wheels and Rollers
- Jenn-Air Dishwasher Wheels and Rollers
- Kenmore Dishwasher Wheels and Rollers
- KitchenAid Dishwasher Wheels and Rollers
- LG Dishwasher Wheels and Rollers
- Magic Chef Dishwasher Wheels and Rollers
- Maytag Dishwasher Wheels and Rollers
- Roper Dishwasher Wheels and Rollers
- Tappan Dishwasher Wheels and Rollers
- Whirlpool Dishwasher Wheels and Rollers