Dishwasher Circuit Boards and Touch Pads

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Original Equipment Manufacturer

Why Genuine OEM Matters
Shop By Brand

Popular Dishwasher Circuit Boards and Touch Pads

Your Price
$125.00
  In Stock
Dishwasher Main Control Board
★★★★★
★★★★★
7 Reviews
PartSelect Number PS16873737
Manufacturer Part Number WD21X32165
This main control board is a genuine OEM part that is designed for dishwashers. It is responsible for controlling the operation of the dishwasher. It monitors all the dishwasher cycles including wash, rinse, dry, and sanitization. It receives input from the control panel and sends commands to various components of the dishwasher, such as the motor, pump, heating element, and sensors, to control the different cycles and functions of the appliance. Signs of a faulty control board include an unresponsive control panel, error codes, interrupted wash cycles, or a burning smell, which indicates a short circuit.
Fixes these symptoms
Installation Instructions
Glen from WARDEN, WA
Dishwasher stopped working
This didn't work out well. At the beginning of September the control panel in the door started to work erratically, the lighted buttons did not light up as expected. I ordered a replacement board and installed it.
CONFIGURED UI SERVICE CONTROL Part #: PS16618944
This did not help, so I ordered another control board and installed it.
CONFIGURED SERVICE MACHINE CONTROL BOARD
Part #: PS16226072.
This did not help. This control board has a small orange fuse that looks like an old fashioned transistor. it was fine, as was the fuse on the previous control board.
There were two things about the Control boards that might help someone figure out what went wrong. When I took out the original control board, there was evidence of component overheating. When I installed the new control board there was a green light that was blinking.
I had hoped to complete this repair, but we have been without a dishwasher for over a month, so I bought a new one.
(I am a competent Instrumentation and Controls technician)
It could be that there is a bigger issue here; a major component failure.
If anyone has some suggestions to try, I would like to repair the machine and sell it as a used appliance. Read more...
Your Price
$211.35
  In Stock
Dishwasher Configured User Interface Control Board
★★★★★
★★★★★
36 Reviews
PartSelect Number PS17137058
Manufacturer Part Number WD21X31902C
This is the user interface control board for various dishwashers. The user interface panel is what you directly interact with on your dishwasher to start and stop it and select the specific cycle you want. If your user interface panel is not responding and you have tested your dishwasher to ensure no other part could be at fault, it will need to be replaced immediately for it to regain function. Replacing this panel will requires some disassembly of your dishwasher, and will require tools like a screwdriver, wrench, and a pair of pliers. This OEM user interface panel measures approximately 14-inches wide and is sold individually.
Fixes these symptoms
Installation Instructions
Brian from MANSFIELD, MA
Dishwasher was randomly beeping when not in use. Then eventually the display wouldn’t light up.
I first tested for 120volts to my dishwasher to verify it was getting power from my electrical panel. Then tested pins 2 and 5 on the control board to make sure there was 14 volts going to the user interface harness. After I verified that I knew it was the user interface that was bad. I watched a video I found on YouTube and followed it. This repair was fairly easy while watching the video and making sure that you use the correct pin out that comes in the box for your model. I’m not an appliance repair person and it took me about an hour start to finish. I’m going to attach the video I https://youtu.be/TI8cUjy5YOE

https://www.youtube.com/watch?v=GN5t4VFgLCY Read more...
Your Price
$70.03
  In Stock
Dishwasher Configured Ui Board
PartSelect Number PS16762507
Manufacturer Part Number WD21X31909
Fixes these symptoms
Installation Instructions
John from DANBURY, CT
UI Control panel would not light up and not work at all. Unplugging D/W failed to correct.
Unplug the dishwasher. Remove toe kick with 1/4 socket. Unplug, by pinching, door harness connector (White terminal connector) from PC board at bottom of dishwasher. Remove the door door using the Allen wrench, place it the hole on side of door hinge where pulley attaches. Unhook the pulley attachment at the door by using a vise grip to pull the plastic up and out. Don't break the plastic! Do the same for the other side. Remove Allen wrench. Pull door in and up at the same time. Take off 2 screws at bottom of door using 1/4 or 5/16 socket. Remove the vent cover (cap) using 2 flat head screwdrivers to loosen. Unscrew by hand. Slide toward the bottom, the inner door panel off from the outer door panel. You will see the door wire harness and some styrofoam insulation. Stand with outer door facing away from you. Remove UI by holding door handle, pressing it and pull the control head, up and away from you. It should come off from the top off the outer door panel. The UI will need to be removed from this housing. Unplug the UI harness connector. Remove 7 screw with a Phillips screwdriver or 1/4 socket. There are 2 clear plastic clips that need to be pressed in to release UI from the housing. Be careful, those clips are easy to snap. Place and snap new UI into the housing. Replace 7 screws. Reattach the connector pug to the new UI board. My personality was factory set. So, no jumper pins on my board. Snap the UI housing back onto the top of your door. Delicately, remove the styrofoam and unsnap the old harness to the soap and drying dispenser. Remove the rest of the old harness. Install the new door harness and use the plastic plugs on the harness to secure to the door. Install the styrofoam insulation. Attach the inner door panel to the outer door panel by sliding inner pan up toward the top. Replace the 2 screws at the bottom of the door. Attach vent cap by hand screwing it on. Position door at the dishwasher. Use Allen wrench or helper to hold at correct angle. Use a vise grip to grab the plastic pulley to attach it to the door hinge. Do the same on the other side. Plug in the harness connector to the PC board. Plug in the dishwasher and the UI should light up! Run a load and make sure no leaks are seen around the door. Replace toe kick. Read more...
Your Price
$74.05
  In Stock
Dishwasher Configured Ui Board
★★★★★
★★★★★
1 Review
PartSelect Number PS16762502
Manufacturer Part Number WD21X31904
Fixes these symptoms
Your Price
$201.79
  In Stock
Dishwasher Control Panel - Stainless
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11769758
Manufacturer Part Number W10910626
The stainless steel control panel assembly is an OEM replacement part for select Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dishwashers. It houses the buttons, LED displays, and electronic components required to operate the dishwasher. Unplug the dishwasher and shut off the water supply before installation. Use gloves for safety. Check your model’s parts diagram for included components and verify compatibility before ordering. This part may not be in stock; contact customer service or check availability online.
Fixes these symptoms
Your Price
$128.34
  In Stock
Dishwasher Configured Ui Board
★★★★★
★★★★★
7 Reviews
PartSelect Number PS16762508
Manufacturer Part Number WD21X31910
The user interface displays the dishwasher settings and lets you select the cycle.
Fixes these symptoms
Installation Instructions
DONALD from GOSHEN, IN
Most of the lights on the control panel had stopped working. There was no way to change the settings of the dishwasher.
When the part arrived, I was pretty sure it was the wrong part. The replacement part had an LED on it -- a box that stuck up about an inch above the circuit board. My dishwasher did not have an LED readout and I was pretty sure the LED would not fit in the space that was available. I was reluctant to take the dishwasher apart until I had the right part. The people at Part Select were helpful and together we looked at the schematic which did, indeed, seem to show a box sticking up from the circuit board. A YouTube video showed me how to take the door off its hinges, unscrew 4 screws and slide the inside of the door upwards. The circuit board went in fairly easily. There was space for the LED (even though it still doesn't show through the top) and now the lights work. Read more...
Your Price
$86.40
  In Stock
Dishwasher Board
★★★★★
★★★★★
3 Reviews
PartSelect Number PS12365196
Manufacturer Part Number 5304512731
This is a genuine control board, which works with dishwashers.
Fixes these symptoms
Installation Instructions
Travis from OAK PARK, IL
Dishwasher not going through the wash cycle
First disconnect the power. Open the dishwasher door. Unscrew all of the screws except the top two screws. Unscrew the top two screws last and slide the door off. Unscrew the housing for the control board. Disconnect the wires from the control board(take a picture or mental note where the wires are positioned for reinstalling). Unscrew the control board. Put the new board in and go in reverse order until the job is complete. Good luck. Read more...
Your Price
$73.10
  In Stock
Dishwasher Configured Ui Board
★★★★★
★★★★★
5 Reviews
PartSelect Number PS16762497
Manufacturer Part Number WD21X31898
Fixes these symptoms
Installation Instructions
Robert from NEW CARLISLE, OH
Dishwasher dead
Repaired with the help of You Tube videos. To repair: remove door (note! the door can be removed without pulling the dishwasher out, or disconnecting spring cables). To remove the door insert allen wrench in holes under door to hold the door in the remove/ install position. separate the inner and outer door (easily done) then remove and replace the User interface board. The hardest part was locating the holes to insert the allen wrenches (or anything similar) in to. Dishwasher worked after repair. In my case the dishwasher would come back to life for a short period if I turned the power off, and back on. I read somewhere that was a symptom of the bad UI board. I was lucky because that was the problem. Read more...
Your Price
$13.67
  In Stock
Dishwasher Control Board Fuse 4.1 Amp
PartSelect Number PS12743197
Manufacturer Part Number WD21X25696
Fixes these symptoms
Your Price
$111.91
  In Stock
Dishwasher Configured Ui Board
★★★★★
★★★★★
7 Reviews
PartSelect Number PS16762498
Manufacturer Part Number WD21X31899
Fixes these symptoms
Installation Instructions
Jason from TULARE, CA
No power to user interface. User interface was beeping for weeks before it powered down.
*Unplug the dishwasher. My drain hose was long enough so no need to disconnect.
Access the motherboard and found a solid green light. This indicates the motherboard is not communicating with the user interface.

Door removal:
- removed kick plate
-unplugged door wire assembly and wire harness clip
-Unscrewed dishwasher from cabinet and pull dishwasher out about 6 inches
-Detached pulley rope assembly from door hinge
-Open door about 4 inches and pull up and towards me.
-Lay the door down, removed vent cap and four T20 screws from the side bottom, remove two 1/4 inch bolt from each hinge(the hinges have four bolts, but only to need to be removed)
-push up on the plastic inner door from outer door and set aside.
-Unscrew four 1/4 inch bolts holding user interface and unplug wire assembly. (The two middle screws are longer than the two outer screws)
-be sure to ground yourself before touching the new user interface board
-read the instructions for the new interface board clip positions(mine was already position correctly)
-Assemble the door and be sure to connect the wire assembly and harness clip. Read more...

Dishwasher Circuit Board or Touch Pad Brands

Back to Top