Dishwasher Caps and Lids
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Dishwasher Caps and Lids
Your Price
$11.95
In Stock
Dishwasher Stop Clip
PartSelect Number PS11770481
Manufacturer Part Number 5304506510
This rail end cap, or dishrack stop clip, is a genuine OEM replacement part for your dishwasher. This part keeps the rack in your dishwasher from sliding out. This is a very easy repair, to complete it you only need a flat blade screwdriver. Use the screwdriver to pry the locking tab open on the cap, located at the front of your upper dishrack. Pull off the end cap and lock the new one into place.
Installation Instructions
Bobby from Austin, TX
Broken wheels, Caps and Brackets. Couldn't hold dishes or wash right.
Just use a hexagonal driver to remove the Upper rack roller, screw the new ones in, place caps on the rail ends, and pop the new wheel on with some pliers! Simple and fun!
Read more...
Your Price
$13.95
In Stock
Dishwasher End Cap
save old rollers from old racks for future repairs Read more...
PartSelect Number PS7783360
Manufacturer Part Number WD12X10426
This is an end cap for a dishwasher rack. This part is about 2.5 inches long, is black, and is made of plastic. You may need to replaced this part if it is broken, or if your dishwasher rack continuously falls off the track or rail.
Installation Instructions
Wilson from MENIFEE, CA
upper and lower rack ASM showed sing of rust
Repair was simple, lower rack just remove and replaced with out any tools or disassemble required, for the upper rack installation, the end cap need to be removed out of the sliding tracks, slide old rack out and discard, clean the track with a suitable cloth and slide new rack in to the tracks, reinstall the old end caps, as a good preventing measure, order new end caps just in case they are need it if the old ones crack during removal. save old rollers from old racks for future repairs Read more...
Your Price
$25.95
In Stock
Dishwasher Rinse Aid Cap
PartSelect Number PS11746426
Manufacturer Part Number WP8558307
The rinse aid cap (sometimes referred to as the dispenser cap), covers the rinse aid dispenser on the dishwasher door. If your dishwasher will not dispense detergent, or it is leaking detergent, there could be an issue with the rinse aid cap. Check the cap and its gasket for any damage or melting. If the cap has melted or it is not sealing the dispenser properly, the part should be replaced right away. This rinse aid cap comes with the gasket, so you should discard the existing gasket and rinse aid cap at the same time. The repair is relatively straightforward, and requires no tools.
Fixes these symptoms
- Door latch failure
- Leaking
- Not cleaning dishes properly
- See more...
Installation Instructions
James from Mesquite, TX
Cap came off and melted
Opened door and installed cap. Not much effort. But really got good service from Parts Select. Received order much faster than I had expected.
Read more...
Your Price
$34.95
In Stock
Dishwasher Rinse Aid Cap
Thank you for stocking the parts and shipping them as promised. Read more...
PartSelect Number PS421128
Manufacturer Part Number 154388801
This is a replacement cap for the detergent/rinse aid dispenser. If the rinse aid cap is damaged or missing, you may notice too much rinse aid in the dishwasher. The cap simply screws into the dispenser, so if your cap is damaged you can simply screw it out, then screw in the new one. The rinse aid cap is approximately 2 inches in diameter and is sold individually. This is an OEM part, directly from the manufacturer.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not drying dishes properly
- See more...
Installation Instructions
Jeffrey from Mildland, MI
Striker
Removed the 4 screws that held the dishwasher in place, tilted it out, removed 2 nut screws on striker, installed new striker and put it back together. Very simple. Thank you for stocking the parts and shipping them as promised. Read more...
Your Price
$26.95
In Stock
Dishwasher Rinse Aid Cap
PartSelect Number PS11755938
Manufacturer Part Number WPW10524919
This part holds the rinse aid liquid in the dispenser until the timer activates the rinse cycle.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not drying dishes properly
- See more...
Installation Instructions
Kathryn from WINTERPORT, ME
Rinse aid cap was melted when it came out of the designated spot and melted against the heat coil.
Open the washer door, remove old rinse aid cap. Place new cap into designated spot, screw into place.
Read more...
Your Price
$25.95
In Stock
Dishwasher Rinse Aid Cap
PartSelect Number PS11748135
Manufacturer Part Number WPW10077881
This part holds the rinse aid liquid in the dispenser until the timer activates the rinse cycle.
Fixes these symptoms
- Door latch failure
- Leaking
- Not cleaning dishes properly
- See more...
Installation Instructions
James from Brandon, FL
Rinse Aid Cap was not secured and during dishwaher run the cap sat on the heating coil and melted.
This is simple, we don't know exactly how, but when we used the dishwasher the cap must not have been twisted correctly, and after the dishwasher shut down we discovered the cap was on the heating coil and melted. I know that it was easy to fix, but the reason I ordered it from PartsSelect was their price was much lower than Kitchen Aids, (the maker), Lowes (where we bought it), and other sites we searched for the part.
Read more...
Your Price
$32.95
In Stock
Dishwasher Rinse Aid Fill Cap
PartSelect Number PS2351824
Manufacturer Part Number WD12X10284
This part helps keep the rinse aid the dispenser until its needed.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not drying dishes properly
- See more...
Installation Instructions
ANNE from SWANNANOA, NC
Lost Despenser Lid, Droped It And Havent Seen It Since.
Ordered the part, by using the diagram on the ge website identified the part and ordered it right them and when it came (delivered really fast) took it out of the bag and screwed it in the jet dry despenser and is working great.
Read more...
Your Price
$18.57
In Stock
Dishwasher Lid
PartSelect Number PS8697157
Manufacturer Part Number 00166623
This OEM-sourced detergent dispenser cover, also known as a rinse aid dispenser lid, seals and protects the detergent compartment in your dishwasher. Typically located on the inner door, it covers the detergent dispenser assembly. When loading the dishwasher, you lift the cover to add rinse aid before running a cycle. If the detergent dispenser cover is broken, you may notice visible cracks, chips, or it may not stay in place properly. If left unreplaced, it can result in detergent leakage during the wash cycle. To remove the cover, first, turn off the power and water supply. Open the dishwasher door and gently insert a flathead screwdriver between the dispenser body and the cover, prying it off. When installing the replacement cover, align it at an angle with the housing and fit one side in before rotating it to snap into place.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Sue E from CARMEL, IN
Rinse aid dispenser lid would not stay closed
Use a screwdriver flat blade to pry up one edge of closed lid. Put one side of lid into hinge and snapped other side into place. Very easy.
Read more...
Your Price
$12.95
In Stock
Dishwasher Tub Cap
PartSelect Number PS11703426
Manufacturer Part Number W10795980
The plastic button covers the sharp ends of screws along the edge of the dishwasher tub. Sold individually.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
Royce from GREENSBORO, NC
Dish rack slide arms losing ball bearings
Unscrewed mounting screws, pulled dishwasher out halfway, replaced arms, 4 screws each side .....very simple 30 min tops. Parts perfect and quick delivery!
Read more...
Your Price
$6.95
On Order
Dishwasher Door Guide Cap
PartSelect Number PS12721288
Manufacturer Part Number DD67-00113B
This dishwasher door cap guide is a genuine OEM replacement designed for Samsung WaterWall dishwashers. The door cap guide serves an aesthetic purpose by hiding mounting screws or other hardware on the dishwasher cabinet. It also protects the hardware from moisture, debris, or hard impacts. It is normal for the cap to become damaged or worn down over time due to normal mechanical stress, aging, or accidents. Over time the cap may crack or break, the adhesive backing may wear down or the cover may be unable to stay securely in place. You will need to replace the door cap or the mounting hardware on the exterior panel will be exposed. Simply pull off the faulty cap and snap the new one into place.
Dishwasher Cap or Lid Brands
- Amana Dishwasher Caps and Lids
- Bosch Dishwasher Caps and Lids
- Crosley Dishwasher Caps and Lids
- Electrolux Dishwasher Caps and Lids
- Estate Dishwasher Caps and Lids
- General Electric Dishwasher Caps and Lids
- Hotpoint Dishwasher Caps and Lids
- Inglis Dishwasher Caps and Lids
- Jenn-Air Dishwasher Caps and Lids
- Kenmore Dishwasher Caps and Lids
- KitchenAid Dishwasher Caps and Lids
- Magic Chef Dishwasher Caps and Lids
- Maytag Dishwasher Caps and Lids
- Roper Dishwasher Caps and Lids
- Whirlpool Dishwasher Caps and Lids