Amana Washer Legs and Foots
Find your part
Enter your model number or a part number and click "Search"
Take a photo of your product’s model number plate and upload it to find parts fast!
Here is an example model number plate:


Popular Amana Washer Legs and Foots
Your Price
$5.51
Foot, Front - Single
PartSelect Number PS11747965
Manufacturer Part Number WPW10001130
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.
Fixes these symptoms
- Shakes and moves
- See more...
Installation Instructions
Paddy from Ferndale, WA
Bearings went out in the drum.
purchased the bearings at Napa auto parts for 16$. Over all it was a little difficult to get the bearings out and back in. Used a brass drift to drive them out and to seat them back in..
Read more...
Your Price
$11.51
Adjustable Levelling Leg
PartSelect Number PS2021026
Manufacturer Part Number 22003428
If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Your washer should be kept as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This genuine OEM replacement part is sold individually, so be sure to order the amount you need.
Fixes these symptoms
- Shakes and moves
- See more...
Installation Instructions
Rebecca from Wylie, TX
Stripped leveler screw making impossible to level my washer
Put blocks under the washer where the leveling leg was needed and screwed the part into the washer. Then it was just a matter of moving the washer into place and leveling. Pretty easy.
Read more...
Your Price
$11.00
Leveling Leg and Pad
PartSelect Number PS11740563
Manufacturer Part Number WP25001119
This leveling leg, which includes a lock nut and a pad, is used to keep washing machines still and balanced. If your washer shakes and moves excessively, then this could be an easy and quick solution to your washers problem. To install, the damaged pulley must be removed to install new pulley. The suggested tools are pliers, a socket set, and/or screwdrivers. For safety precautions, make sure to unplug washer from power source or shut off the house circuit breaker. Remember to wear gloves prior to starting this installation project. Refer to the instructional diagram provided by the manufacturer for further guidance. Customers suggested the detailed diagram as helpful.
Fixes these symptoms
- Shakes and moves
- See more...
Installation Instructions
John from Cumberland, MD
Washing Machine Beat Itself To Death During Spin Cycle
Removed front cabinet, removed 6 springs holding tub down, removed pump hose, removed drive belt from motor,lifted tub out the top and placed upside down, loosened all six hex bolts(did not loosen or remove drive pulley) backed all six bolts out and left 4 threads showing, slipped old snubber out cleaned all surfaces with alchohol and slid new snubber in. Put corn starch on base where snubber rides, lifted tub back in, hooked up all six tension springs with auto brake tool. Put belt back on. . . Done. . No more beating itself to death.
Read more...
Your Price
$11.15
Leveling Foot
PartSelect Number PS11744907
Manufacturer Part Number WP8181636
Sold Individually.
Installation Instructions
Lydia from Cincinnati, OH
Clothing ripped my bellow.
I removed the outer tub clamp using two needle-nosed pliers. Then I folded the bellow back and removed the bellow from the dispensing outlet. I then losened the bellow clamp using a screw driver. It was on there very securely. Then I had my daughter with her smaller hands finish untightening the screw enough to release the bellows from the machine. Then the bellow and clamp were taken out of the machine carefully, not scratching anything and noting orientation for new bellow. I cleaned the machine surfaces. Next, lining up the top notch on the bellow, it was worked into the groove around the entire inner basket. The bellow also had to have the hole covering placed over the dispensing outlet. This was the most time consuming. Just to make certain that it was positioned correctly took 20 minutes. I then put the bellow clamp back on and tightened it to the very tight positioned it was in prior to being removed. My daughter returned to help with the smaller bellow clamp that goes to the front of the machine. I needed help keeping one side of the clamp in placed while the other side was stretched out again to go onto the bellow. Then the machine was leveled top to back, side to side, leg nuts tightened. Works quieter than ever.
Read more...
Your Price
$13.58
Rear Leveling Foot
PartSelect Number PS334463
Manufacturer Part Number 285244
Sold Individually. Used to help stabilize the appliance on uneven surfaces.
Fixes these symptoms
- Shakes and moves
- See more...
Your Price
$10.64
Leveling Leg with Foot
PartSelect Number PS11738005
Manufacturer Part Number W10862938
Sold individually.
Fixes these symptoms
- Shakes and moves
- See more...
Your Price
$13.78
Rear Leveling Leg and Foot with Pad
PartSelect Number PS11739532
Manufacturer Part Number WP22004469
Sold individually.
Fixes these symptoms
- Shakes and moves
- See more...
Installation Instructions
James from ELMORE, OH
Washer Traveled and load would not be balanced. Washer would bang loudly.
Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.
Read more...
Your Price
$10.24
Single Motor Grommet
PartSelect Number PS11743304
Manufacturer Part Number WP62691
Sold Individually.
Fixes these symptoms
- Pumps but will not spin
- Will not agitate
- See more...
Installation Instructions
Robert from Friendswood, TX
Spider coupling between motor and transmission broken
Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy repair.
Read more...
Your Price
$5.51
Rubber Foot Pad
PartSelect Number PS11742245
Manufacturer Part Number WP40016001
This foot pad is just over an inch in diameter. It is all black in color and is made entirely of rubber. This pad is used for the levelling legs of many washing machines.
Your Price
$10.55
Related Parts
- All Amana Washer parts
- Amana Washer Agitators
- Amana Washer Belts
- Amana Washer Brackets and Flanges
- Amana Washer Caps and Lids
- Amana Washer Circuit Boards and Touch Pads
- Amana Washer Dispensers
- Amana Washer Drums and Tubs
- Amana Washer Hardware
- Amana Washer Hinges
- Amana Washer Hoses and Tubes
- Amana Washer Knobs
- Amana Washer Latches
- Amana Washer Motors
- Amana Washer Pulleys
- Amana Washer Pumps
- Amana Washer Seals and Gaskets
- Amana Washer Springs and Shock Absorbers
- Amana Washer Switches
- Amana Washer Transmissions and Clutchs
- Amana Washer Valves
- Amana Washer Wire Plugs and Connectors