Parts That Fix Frigidaire Refrigerator FRS6R5ESB4 Ice maker not making ice

This door bin (Bottom Door Bin, Refrigerator Door Bin, Door Shelf Bin, Refrigerator Door Bin) is a movable bin mounted on the inner door to hold food items, bottles, and jars. Over time, a cold refrigerator can cause plastic to become fragile and break down. This can lead to other issues in the refrigerator. When the door bin will not hold securely onto the inner door panel, it must be replaced. This door bin measures 5.75 inches high, 16 inches wide, by 4.25 inches deep and is made of white plastic. Sold individually.

This dispenser crusher housing may also be known as a refrigerator ice crusher housing, and is compatible with your refrigerator. The function of the dispenser crusher housing is to shield the ice crushing blades within the ice container. To make this repair you will need a Phillips screwdriver, a flat blade screwdriver, a quarter-inch nut driver, and a pair of channel lock pliers. For this installation, work gloves are recommended. Note that this piece may look different or be a different color than the original, but this part will fit and function in the same way as the original part.

The ejector drive gear is a part for your refrigerator. This icemaker drive gear is for the ejector blades. The part rotates the cube ejector arm, which cycles the icemaker and pushes the cubes out and into the ice bucket, ready for the ice to be used. The outside diameter of this piece is almost two inches by two inches. The reason for needing to replace your gear is if the current one is broken/missing a tooth, or if your icemaker is not dispensing ice and is noisy.

Bucket only. All other parts sold separately.

This drive blade is a little under five inches long. It is used for the icemaker of many refrigerators.

This part helps push the ice through the front plate to be crushed.

The ice stripper goes on the front of the ice maker and directs the ice cubes from the maker to the bin. Due to the frigid temperatures, the plastic breaks down and cracks from time to time. This may cause the ice cubes to get stuck in the ice maker and not dispense properly. You will need to open the freezer door, pull out the ice container by lifting and pulling out. Unplug the ice maker by releasing the locking tabs. Use your 1/4-inch nut driver to remove the screws holding the ice maker in place. Take the ice maker out of the freezer for easy access. The ice stripper can be removed by simply unlatching from the pin holding it in place. The new ice stripper should just click into place so the tab goes into the control head with ease.

This is a water fill tube which is used in refrigerators. It attaches to the water inlet valve and supplies water to the components in your appliance that need it, such as the icemaker and water dispenser. You will need to replace your fill tube if you notice it is leaking or damaged. This replacement tube is approximately 7 inches in length, and it is made entirely of plastic. The fill tube is sold individually. Before you begin repairing your refrigerator, make sure the water supply has been turned off and that the appliance has been unplugged.

The cube solenoid allows cube or crushed ice to be dispensed on demand. 120V 60Hz

This is the ice actuator or ice actuator arm for your refrigerator. When you depress the actuator arm with a glass or bucket, ice is normally dispensed. If your current actuator arm is broken, missing, or if the ice dispenser isn’t dispensing ice, you may need to replace it. To access the actuator, you will first need to remove the dispenser assembly, and then remove the actuator from the assembly. Be sure to shut off the water and power source from your refrigerator before you begin this repair.

This genuine replacement shutoff arm spring is for refrigerator ice makers. It applies tension to the ice maker shutoff arm to hold it in place so that the ice maker will stop making ice when the ice bucket is full. If your ice maker continues to make ice when your bucket is full, you may need to replace this shutoff arm spring. This part is less than 2 inches long, and is made entirely of metal. Be sure to disconnect the power or the water supply to your refrigerator before completing this repair.