Models
>
AD65USR0
AD65USR0 Whirlpool Dehumidifier - Overview
Sections of the AD65USR0
[Viewing 3 of 3]
Manuals & Care Guides for AD65USR0
Click to downloadKeep searches simple, eg. "belt" or "pump".
Float
PartSelect #: PS11738360
Manufacturer #: WP1172075
If the bucket is full indicator on your dehumidifier is on but the bucket is empty, you may have a problem with the float. If you notice that the float is warped or damaged, it should be replaced. Thi...
$8.04
In Stock
Hex Nut
PartSelect #: PS11742711
Manufacturer #: WP488130
This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, refrigerators, air cond...
$9.56
In Stock
Bucket and Float Kit
PartSelect #: PS1486706
Manufacturer #: 8201783
This bucket and float kit, also known as water tank assembly, is for a dehumidifier is 14.5 inches long and 8.5 inches wide. The water tank extracts, traps, and contains the moisture from the air, whi...
No Longer Available
Single Hex Head Screw
PartSelect #: PS11742731
Manufacturer #: WP489069
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
$5.42
In Stock
Fan Motor
PartSelect #: PS557949
Manufacturer #: 4389130
This fan motor controls the circulating fan in the dehumidifier.
$276.27
Special Order
Zip Tie
PartSelect #: PS11753208
Manufacturer #: WPW10339879
A zip tie, also known as a cable tie or a wire tie, is a fastening device that holds wires or tubing together. If a machine has wires or tubing that are easily shifted, you need to hold them tightly t...
$8.04
In Stock
Questions And Answers for AD65USR0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The dehumidifier did not turn off automatically when the collection bucket was full (or removed).
The microswitch that senses a full or missing collection bucket can almost be removed without taking off the cover of the dehumidifier, but the arrangement and orientation of connector contacts makes that very difficult. It took me five minutes to remove the cover (Phillips head screwdriver), 30 seconds to replace the switch, and a few m
... Read more
inutes to re-install the cover. Works like a champ.
Read less
Parts Used:
-
Michael from Madison, NC
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the dehumidifier was not shutting off when water level was full
replaced a piece of the plastic at the top of the bucket that seems to be the water gauge. this seems to be fixed. we are very happy
Parts Used:
-
Steven from Owings Mills, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bad control on 1998 Whirlpool dehumidifier
Disassemble all the housings starting with front cover, top, sheetmetal side/back piece and top styrofoam support. The top slides back 3/8" before you can lift it up off the keys. Carefully pry/pop the control board loose from the top piece and swap all the wires. Had to cut loose 2 zip-ties to re-route the tank switch wires: immediately
... Read more
replace with new zip-tie left full loose so new wires can be re-routed without wiring bundle falling all over. Get all the wires positioned and finish tightening up the zip-ties, but not all the way, just like the factory did. Cut the tails on the ties.
While all the housings were off I vacuumed off the parts and coils and washed the fan blades off with soapy water and a sponge. Looked for chafed wires and such. Trimmed the coil case up with sheet metal shears where it was rubbing on the styrofoam bottom tray and gently filed the cut smooth.
Reassembly: snap the board back into the top piece, put the styrofoam top support on, then the side/back metal, then the top, dropping it onto the keys and sliding it forward again. The front piece goes on last.
While all the housings were off I vacuumed off the parts and coils and washed the fan blades off with soapy water and a sponge. Looked for chafed wires and such. Trimmed the coil case up with sheet metal shears where it was rubbing on the styrofoam bottom tray and gently filed the cut smooth.
Reassembly: snap the board back into the top piece, put the styrofoam top support on, then the side/back metal, then the top, dropping it onto the keys and sliding it forward again. The front piece goes on last.
Read less
Parts Used:
-
Alan Van from Springfield, OR
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!