Models
>
ZSC2000FWW02
ZSC2000FWW02 General Electric Microwave - Overview
Sections of the ZSC2000FWW02
[Viewing 7 of 7]Manuals & Care Guides for ZSC2000FWW02
Click to downloadKeep searches simple, eg. "belt" or "pump".
Primary Door Interlock Switch
PartSelect #: PS237015
Manufacturer #: WB24X10047
This interlock switch is located in the door latch.
$33.44
In Stock
Light Bulb
PartSelect #: PS1481517
Manufacturer #: WB36X10328
Sold individually. Appliance may take 2.
$26.65
In Stock
Turntable
PartSelect #: PS227932
Manufacturer #: WB06X10219
Also known as rotating ring assembly.
No Longer Available
Cooking Tray
PartSelect #: PS7783326
Manufacturer #: WB49X10246
NOTE: This is a manufacturer substitution. Part may differ in appearance and size but is a functional equivalent to prior part.This tray rotates in your microwave ensuring more even temperatures.
No Longer Available
Oven Cavity Temperature Cut-Out
PartSelect #: PS235672
Manufacturer #: WB21X10046
Also known as fuse.
$44.06
In Stock
Questions And Answers for ZSC2000FWW02
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the ZSC2000FWW02
[Viewing 4 of 4]Won’t turn on
Fixed by
these parts
these parts
Show All
No heat
Fixed by
these parts
these parts
Show All
Tray won’t turn
Fixed by
these parts
these parts
Show All
Doesn’t shut off
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave runs with the door open
Remove microwave outer cover. Turn on side & locate the upper & lower door switches. Better to replace in pairs even if one is ok. Remove the wire harness to each switch. Then replace switch and re connect the wire harness. Re attach outer cover
and test to see if that solved the problem. If so then well done!!
and test to see if that solved the problem. If so then well done!!
Parts Used:
-
Thomas from Andover, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
35 of 50 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave would turn on and count down, but not heating and not rotate turntable. Pressing door up would occasionally start heat.
First I disconnected the power and opened the door. Then I removed the top screws holding the top vent louvers, then removed the screw at the top of the touch pad. The touch pad removes by sliding up slightly then tilting top out. I unscrewed two screws holding the door latch assembly. Press the tab to remove and replace switch. Reco
... Read more
nnect wires, reseat latch mount by placing top bracket tab in place first, allign and secure with screws. Reseat touch pad by placing bottom tabs in first, tilt forward and press up to seat top tabs, secure with top screw. Secure vent louver screws, plug in and watch your microwave work again.
Read less
Parts Used:
-
Michael from Ridgefield, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
37 of 58 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken shaft -- turn table would not turn.
Safety TORX driver removed screw. Ceramic cover removed with ease. Shaft pulled straight up and out. Broken piece not retreivable and left in base of oven. New shaft inserted over "D" stub. Ceramic cover replaced and screw tightened.
When the ceramic cover is removed, this allows the glass cover for the UV heating unit to ... Read more be removed, cleaned, replaced. I recommend doing this.
When the ceramic cover is removed, this allows the glass cover for the UV heating unit to ... Read more be removed, cleaned, replaced. I recommend doing this.
Read less
Parts Used:
-
James from OKLAHOMA CITY, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
22 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!