Models
>
ZMC1095SF03
ZMC1095SF03 General Electric Microwave - Overview
Sections of the ZMC1095SF03
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Light Bulb - 40W 130V
PartSelect #: PS247209
Manufacturer #: WB36X10003
This light bulb is a 40 watt, 130-volt clear appliance light bulb that is manufactured to fit microwaves with small-base light bulb sockets. The light bulb illuminates the inside of the microwave whil...
$22.00
In Stock
Diode
PartSelect #: PS239740
Manufacturer #: WB27X10597
This part allows power to go one way only.
$60.79
In Stock
Magnetron Assembly
PartSelect #: PS239204
Manufacturer #: WB27X10089
This part is used to generate microwave energy/heat.
$236.54
In Stock
Capacitor
PartSelect #: PS239120
Manufacturer #: WB27X10011
The capacitor is an electric circuit element that is used to store charge temporarily.
$112.83
In Stock
Exterior Door Panel - Stainless Steel
PartSelect #: PS247326
Manufacturer #: WB36X10122
Also known as Inlay Screen Assembly.
No Longer Available
Complete Door Assembly - Stainless Steel
PartSelect #: PS754591
Manufacturer #: WB55X10550
No Longer Available
Questions And Answers for ZMC1095SF03
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mary
February 15, 2020
Our microwave turns on but not heating, where can we look at it to check the diode? How can we get to it?
For model number ZMC1095SF03
Hi Mary. Please read our guide here: https://www.partselect.com/Microwave+test-diode+repair.htm. Thank you for your question and good luck with your repair.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
Common Symptoms of the ZMC1095SF03
[Viewing 2 of 2]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bulb had broken off in base that was still screwed into socket
At first I tried to use pliers to unscrew the base,very uncomfortable working position,upside down and backwards(the microwave is installed over the range top)very limited space for your body and arms to manuver and you really cant see the base,all of this took place after the breaker was turned off ofcourse,finally figured out that you c
... Read more
an drop the entire bottom housing of the microwave by unscrewing 6 screws and the light sockets are easily accessable once you lower it,take out 1 retaining screw ,remove the entire socket and unscrewed the broken base and replaced the bulbs,I said bulbs,there is no sense in having to replace another bulb in who knows how long since only one had burned out but they were both the same age
Read less
Parts Used:
-
william from san antonio, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
92 of 104 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not working as far as heating or cooking
Replaced High Voltage Diode. Very carfully due to the extream danger of a electrical shock.
Parts Used:
-
Theodore from Medical Lake, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
151 of 358 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
microwave would not heat up
I removed the microwave unit (built-in) from the housing above the built-in oven with just two screws and unplugging it. I then removed the screws from the top and sides of the microwave access panels to allow access to the magnetron. I then removed the electrical connections from the magnetron, which is very simple and then the screws w
... Read more
hich held the magnetron in place. Replacement of the new part was just the reverse of removing the other one. Cost to do this by a technician would have been somewhere in the neighborhood of $65.00 for coming to the house, and $75.00 per hour rounded to probably 2 hours to do it. So, doing this yourself is satisfying not only in knowing you did the job, but the $200.00 plus dollars you saved as well.
Read less
Parts Used:
-
Thomas from Gilbert, AZ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
34 of 38 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!