Models
>
WTW7800XW0
WTW7800XW0 Whirlpool Washer - Overview
Sections of the WTW7800XW0
[Viewing 5 of 5]
Manuals & Care Guides for WTW7800XW0
Click to downloadInstall
Installation Instructions
(3.56MB)
Install
Installation Instructions
(6.2MB)
Install
Installation Instructions
(2.69MB)
Install
Installation Instructions
(2.72MB)
Manual
Owner's Manuals
(8.93MB)
Manual
Owner's Manuals
(9.64MB)
Specs
Product Specifications Sheet
(0.26MB)
Keep searches simple, eg. "belt" or "pump".
Drain Pump
PartSelect #: PS5136124
Manufacturer #: W10536347
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
$136.02
In Stock
Basket Hub Kit
PartSelect #: PS11723155
Manufacturer #: W10820039
This kit includes one driver hub and two driven basket hubs. The basket hub is located under the agitator. If your washer is not agitating or spinning properly, the hubs will need to be replaced.
$37.73
In Stock
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Lid Lock Assembly
PartSelect #: PS11756782
Manufacturer #: WPW10619844
This part makes sure that the lid is shut before allowing the machine to start or agitate.
NOTE: This is a manufacturer substitution. Part may differ in appearance but is a functional equivalent to prior parts including
$94.96
In Stock
Screw
PartSelect #: PS11742721
Manufacturer #: WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
$7.91
In Stock
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Screw, 8-16 x 1.000
PartSelect #: PS11746167
Manufacturer #: WP8533953
Sold individually.
$7.95
In Stock
Inlet Hose - 5 FT
PartSelect #: PS11746820
Manufacturer #: WP89503
This hose can handle hot or cold water and is five feet long.
$21.53
In Stock
Sensor
PartSelect #: PS11749664
Manufacturer #: WPW10178988
This rotary position sensor is a genuine OEM part for your washing machine. It helps to ensure the load of clothing stays balanced during the wash cycle. Customers have rated this repair as easy. To c...
$43.95
In Stock
Spray Paint - 12 oz. - White
PartSelect #: PS347819
Manufacturer #: 350930
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
$22.68
In Stock
Wire Hinge - Left Side
PartSelect #: PS11746533
Manufacturer #: WP8563965
This lid hinge is a genuine OEM replacement part for your washing machine. This hinge is for the left side of your lid, although it is a good idea to replace btoh hinges at once. The hinge holds up th...
$25.32
In Stock
Questions And Answers for WTW7800XW0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Elvin
July 6, 2021
Trying to replace a lid and hinges and what ever else comes with it.
For model number WTW7800XW0
Hello Elvin, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is Part #: PS11753409 for the White Lid, Part #: PS11753407 for Silver and Part #: PS11753406 for Black. The Wire Hinges are Part #: PS11746533 for Left and Part #: PS11746675 for the Right. The Hinge is Part #: PS11752463 for the Left and Part #: PS11752464 for the Right. The Part #: PS12741703 is the screw for the wire hinge and Part #: PS11743784 for the Hinge Screw. Please feel free to contact Customer Service at 1-888-738-4871 from 8:00 AM to 10:00 PM Eastern time, 7 days a week if you need help placing an order. We are looking forward to hearing from you!
Was this helpful?
Thank you for voting!
Related Parts:
Screw
$7.95
In Stock
SCREW
$16.27
In Stock
Wire Hinge - Right Side
$24.39
In Stock
Wire Hinge - Left Side
$25.32
In Stock
Lid - Black
$356.62
In Stock
Lid - Silver
$445.42
No Longer Available
Lid - White
$336.37
In Stock
Giovanni
January 5, 2023
Washer begin with water filling, after that it stop a wont spin, strange noise before stopping
For model number WTW7800XW0
Hello Giovanni, thank you for contacting us. The issue is most probably related to a damaged basket hub kit, part number PS11723155. It connects the spin basket to the spin shaft that spins the basket. We would also recommend checking the sensor, part number PS11749664. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
Was this helpful?
Thank you for voting!
Related Parts:
Sensor
$43.95
In Stock
Basket Hub Kit
$37.73
In Stock
Gary
January 8, 2023
What part do i need to keep the glass down in the back of the lid. It’s leafing up on the right side?
For model number WTW7800XW0
Hello Gary, Thank you for your inquiry. Researching the model number that you have provided, if the glass is separating from the frame in the lid, then we would recommend replacing the lid assembly. Good luck with your repair.
Was this helpful?
Thank you for voting!
Related Parts:
Lid - White
$336.37
In Stock
Lid - Black
$356.62
In Stock
- < Prev
- 1
- Next >
Common Symptoms of the WTW7800XW0
[Viewing 8 of 8]Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Loose change entered drain pump, cracked housing leaked all water out
Disconnect power, hot/cold supply and drain hose. Tip washer onto front side, expect some additional water to leak out. Remove the cracked drain pump, 3 screws, hose clamps, and electrical plug.
Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover ... Read more over the outer and inner tubs. Pop the center cap from inside the inner tub, exposing the bolt holding the inner tub down. Remove bolt, pull inner tub up and out.
At bottom of outer tub remove 2 screws from drain access cover, should find some change under there (or in the pump).
Re-assemble using new pump.
Note:
Before new pump arrived I was able to use some silicone sealant, epoxy, and black tape to temporarily fix the cracked pump housing after pulling it out.
Tip washer back up, use the putty knife to pop the top cover up (clips are about 6.5in in from sides). Unclip the white plastic cover ... Read more over the outer and inner tubs. Pop the center cap from inside the inner tub, exposing the bolt holding the inner tub down. Remove bolt, pull inner tub up and out.
At bottom of outer tub remove 2 screws from drain access cover, should find some change under there (or in the pump).
Re-assemble using new pump.
Note:
Before new pump arrived I was able to use some silicone sealant, epoxy, and black tape to temporarily fix the cracked pump housing after pulling it out.
Read less
Parts Used:
-
ROBERT from BARRINGTON, IL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
204 of 236 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water pump for draining
The actual install of the pump was extremely easy. I removed the back cover, (After unhooking water, drain and electricity. I laid the machine on its front ( USE CAUTION WHEN DOING THIS, THERE ARE SHARP EDGES on the FRAME) After bandaging my cut fingers, I used a nut-driver/screwdriver to remove the screws, pliers to remove the Spring cla
... Read more
mps, unhooked the wiring( its a single plug in) and reverse the procedure for installing.
I saw where a person had put the screws in the filter below the tub. I had to find the clips on the front of the machine, (about 7 in in from the sides) I removed the nut cover on the agitator, used a socket to remove the agitator, tub, and a nut driver to remove the filter. I found 3 areas where coins could get through the drain filter, and I used self tapping screws to make an obstruction that water could get through but not the coins. I reinstalled tub. Before re installing the agitator, I got some fiber glass window screening and cut a piece to go over the drain slots in the bottom of the tub but under the agitator, then reinstalled the agitator.
I noticed that the new pump had more re enforcing at the areas where the 1st pump broke. I doubt that it will break, but I am not taking any chances. I put the screen in to prevent the coins from getting to the drain filer 1st and the back up was the screws in the drain filter.
I saw where a person had put the screws in the filter below the tub. I had to find the clips on the front of the machine, (about 7 in in from the sides) I removed the nut cover on the agitator, used a socket to remove the agitator, tub, and a nut driver to remove the filter. I found 3 areas where coins could get through the drain filter, and I used self tapping screws to make an obstruction that water could get through but not the coins. I reinstalled tub. Before re installing the agitator, I got some fiber glass window screening and cut a piece to go over the drain slots in the bottom of the tub but under the agitator, then reinstalled the agitator.
I noticed that the new pump had more re enforcing at the areas where the 1st pump broke. I doubt that it will break, but I am not taking any chances. I put the screen in to prevent the coins from getting to the drain filer 1st and the back up was the screws in the drain filter.
Read less
Parts Used:
-
Kerry from Alleyton, tX, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Socket set
67 of 80 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The washer was making a horrible noise during the spin cycle
Removed a cap in the center of the tub basket which has a bolt that needs removed I believe it's a 9/16 after I removed the bolt I then removed the center of the bottom of the basket assembly which then allowed me to get to the basket hub that needed replaced it was a little dirty and I couldn't get it out so I sprayed a little penitratin
... Read more
g oil on it let it sit a little then I was able to remove the hub and install the new one then I put it all back together and the washer is working great
Read less
Parts Used:
-
Kevin from CLARK, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
47 of 57 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!